American Standard Amarilis 3801 SERIES User manual

SPREAD LAVATORY
FAUCETS
Installation
Instructions
43167A
3801 SERIES
3841 SERIES
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
CLIP
AERATOR
SEAL
WASHERS
COUPLING
NUT
O-RING
WRENCH
LIFT
ROD
RUBBER
WASHER
BRASS
WASHER
LOCKNUT
TEE
THUMBSCREW
HANDLE
SCREW
HANDLE
ADAPTER
CARTRIDGE
ESCUTCHEON
RUBBER
RING
RUBBER
WASHER
BRASS
WASHER
LOCKNUT
VALVE
ASSEMBLY
O-RING
SCREW
RUBBER
RING
Certified to comply with ANSI A112.18.1M
U.S. Patent No. 5,819,789
SPOUT
ESCUTCHEON
STOPPER
DRAIN
FLANGE
GASKET
WASHER
NUT
DRAIN
BODY
EXTENSION
PIVOT
ROD
TAILPIECE
RUBBER
RING
O-RING
SPOUT
ESCUTCHEON
LIFT
ROD
AERATOR
IRIS (3841)
SPOUT
JASMINE (3801)
SPOUT

Product names listed herein are trademarks of American Standard Inc.
American Standard Inc. 1999
C
Turn off hot and cold water supplies before beginning. VALVE INSTALLATION
SERVICE
1
6
2
LEDGE
RUBBER
WASHER
BRASS
WASHER
LOCKNUT
VALVE
BODY
5/16''
MIN.
ESCUTCHEON
RUBBER
RING
LOCKNUT
CARTRIDGE
SCREEN
SPRING
CLIP
STOP
WASHER
BRASS
WASHER
RUBBER
WASHER
SINK
Insert SPOUT shank through center
hole of SINK, making sure RUBBER RING
is properly positioned.
SPOUT ASSEMBLY
Assemble RUBBER WASHER, BRASS
WASHER and LOCKNUT onto threads of
SPOUT from underside of SINK.
Insert LIFT ROD through SPOUT
and slot of BRASS WASHER.
Align SPOUT and tighten LOCKNUT.
Be sure slot in BRASS WASHER is
positioned to the rear as shown.
Insert VALVE BODY through hole from
underside of SINK. Thread of VALVE
BODY should extend at least 5/16 inch
above SINK top. If necessary, adjust
LOCKNUT.
Place RUBBER RING into ESCUTCHEON
and screw ESCUTCHEON onto VALVE
BODY until snug against internal stop.
Set VALVE BODIES so that their outlets
are facing toward center of SINK.
Tighten LOCKNUT using wrench supplied
with faucet.
TEST INSTALLED FAUCET
5Remove AERATOR.
With handle in OFF position, turn on water supplies and check
all connections for leaks.
Operate both handles to flush water lines thoroughly. Check
spout mounting and hose connections for leaks.
Operate LIFT ROD and check DRAIN for leaks.
Turn handles into OFF position and replace AERATOR.
To change direction of handle rotation,
proceed as follows:
Turn valve to OFF position.
Remove INSERT and HANDLE SCREW.
Slip HANDLE with ADAPTER off.
Remove SPRING CLIP.
Lift STOP WASHER, turn 90°and replace.
Replace SPRING CLIP.
Replace ADAPTER, HANDLE, SCREW, and INSERT.
AERATOR may accumulate dirt causing distorted and reduced
water flow. Remove AERATOR and rinse clean.
If spout drips, operate handles several times from OFF to ON
position. Do not force - handles turn only 90°.
Plastic SCREEN in CARTRIDGE may accumulate
dirt causing reduced water flow. To clean, first
turn off hot and cold water supplies, then:
Remove INSERT and HANDLE SCREW.
Slip HANDLE with ADAPTER off.
Unscrew CARTRIDGE with wrench.
Thoroughly rinse plastic SCREEN at
base of CARTRIDGE.
Replace CARTRIDGE until flange is
tight against valve body.
Turn valves OFF.
Replace ADAPTER, HANDLE, SCREW,
and INSERT.
TEE
SCREW
COUPLING NUT
O-RING
Before connecting TEE make certain that O-RINGS are
properly seated on SPOUT SHANK and SCREW.
Place WASHERS inside COUPLING NUTS of HOSE and
connect HOSE to each valve outlet. Tighten COUPLING NUTS.
Connect HOT water supply to the left valve and the COLD
water to the right valve using sealant and appropriate
connectors and coupling nuts.
Push SCREW into TEE and tighten SCREW onto SHANK
to secure SPOUT connection.
SPOUT
SHANK
3TEE AND HOSE INSTALLATION
INSTALL POP-UP DRAIN STOPPER
Push TAILPIECE down into TRAP (threaded end up).
Thread LOCKNUT, WASHER and GASKET onto
DRAIN BODY.
Apply a bead of PUTTY to underside of FLANGE.
Feed DRAIN BODY up through SINK and thread
FLANGE fully onto BODY.
Tighten LOCKNUT firmly, keeping the PIVOT ROD
pointed towards the back of the SINK.
Drop STOPPER into DRAIN BODY.
Pull TAILPIECE up and thread tightly
into DRAIN BODY.
Position EXTENSION ROD onto POP-UP ROD and
tighten THUMBSCREW.
Remove one end of CLIP from PIVOT ROD by squeezing
ends together while sliding.
Insert PIVOT ROD into second or third hole in EXTENSION
and reassemble CLIP. (EXTENSION may need to be bent.)
Adjust STOPPER height by repositioning EXTENSION and
tightening THUMBSCREW.
FLANGE
SINK
GASKET
PIVOT
ROD
DRAIN
BODY
PUTTY
WASHER
LOCKNUT
TAILPIECE
TRAP
TAILPIECE CLIP
THUMBSCREW POP-UP ROD
CLIP
PIVOT
ROD
EXTENSION
ROD
4
RUBBER
RING
43167A
TRAP
EXTENSION
ROD
Refer to separate "Instruction Sheet" for
assembly of handles.
O-RING
HOTLINE FOR HELP
For toll-free information and answers to your questions, call:
1 [phone]
Weekdays 8:00 a.m. to 7:00 p.m. Eastern Time
Saturdays 8:00 a.m. to 4:00 p.m. Eastern Time
IN CANADA 1-800-387-0369 (TORONTO 1-416-536-5609)