American Standard Cadet RIght Height 16-1/2" Height Pressure-Assisted EL Toilet... Operating and safety instructions

M45
© 2008 AS America Inc. Revised 2/08
To Be Specied:
❏ Color: ❏ White ❏ Bone ❏ Linen
❏ Silver ❏ Fawn Beige ❏ Black
❏ Seat: American Standard #5324.019 “Rise and
Shine” (with easy to clean lift-off hinge system)
solid plastic closed front seat with cover.
❏ Seat: American Standard #5311.012 “Laurel”
molded closed front seat with cover.
❏ Alternate Seat:
❏ Supply with Stop:
* Flushmate III tank system by Flushmate® Div. of Sloan Valve Co
CADET™ RIGHT HEIGHT 16-1/2" HEIGHT
PRESSURE-ASSISTED EL TOILET
VITREOUS CHINA
CADET™ RIGHT HEIGHT 16-1/2"
PRESSURE-ASSISTED ELONGATED TOILET
❏ 2377.100
• Vitreous china
• Low-consumption (1.6 gpf/6.0 Lpf)
• Bowl rim at 16-1/2"
• Elongated bowl
• Pressure-assisted siphon jet ush action
• Fully-glazed 2" ballpass trapway
• 10" x 12" water surface area
• Close-coupled Flushometer tank*
• Side-mounted chrome trip lever
• Speed Connect® tank/bowl coupling system
• Sanitary dam on bowl
• Two bolt caps
• 100% factory ush tested
❏ 3109.016 Bowl with two bolt caps
❏ 4098.100 Tank complete with
coupling components
Nominal Dimensions:
806 x 495 x 800mm
(31-3/4" x 19-1/2" x 31-1/2")
Fixture only, seat and supply by others
Recommended working pressure range
20 psi - 80 psi
Alternate Congurations Available:
❏ 3109.456 Elongated bowl only with slotted
rim for bedpan holding
❏ 4098.700 Tank and tank cover only with tank
cover locking device
❏ 4098.800 Tank and tank cover only with right
hand trip lever
❏ 4098.900 Tank complete with right hand trip
lever and tank cover locking device
Compliance Certications -
Meets or Exceeds the Following Specications:
• ASME A112.19.2 for Vitreous China Fixtures
NOTES:
THIS TOILET IS DESIGNED TO ROUGH-IN AT A MINIMUM DIMENSION
OF 305mm (12") FROM FINISHED WALL TO C/L OF OUTLET.
SUPPLY NOT INCLUDED WITH FIXTURE AND MUST BE ORDERED
SEPARATELY.
* DIMENSION SHOWN FOR LOCATION OF SUPPLY IS SUGGESTED.
IMPORTANT: Dimensions of xtures are nominal and may vary within
the range of tolerances established by ANSI Standard A112.19.2. These
measurements are subject to change or cancellation. No responsibility is
assumed for use of superseded or voided pages.
12
(305mm)
31-3/4
(806mm)
C/L OF OUTLET
3-1/4
(83mm)
FINISHED WALL
8-7/8
(225mm)
3/4 ±1/4
(19mm ±6mm)
16-1/2
(419mm)
18-1/2
(470mm)
C/L OF SEAT POST HOLES
5-1/2 (140mm CENTERS)
13-3/8
(340mm)
5-3/4
(146mm)
5/8
(16mm) FINISHED
FLOOR
31-1/2
(800mm)
10
(254mm)
6
(152mm)
19-1/2
(495mm)
10
(254mm)
SUPPLY
AS
REQ'D
15
(381mm)
*
*
MEETS THE AMERICANS WITH DISABILITIES ACT GUIDELINES
AND ANSI A117.1 REQUIREMENTS FOR ACCESSIBLE AND USABLE
BUILDING FACILITIES - CHECK LOCAL CODES.
When installed so top of seat is 432 to 483mm (17" to 19") from the
finished floor.
BARRIER FREE