American Standard COLONY SOFT 2175.503 User manual

- 1 -
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2017
Congratulations on purchasing your American Standard faucet
with Speed Connect drain, a feature found only on American
Standard faucets.
Speed Connect®Drain*
• 1/3 of the parts, installs in 1/3 of the time
• No tools needed
• Never needs adjustment
• Guaranteed to seal properly the rst time, every time.
*Your new American Standard faucet is designed to work only with the Speed Connect drain.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
RECOMMENDED TOOLS
1
M968882 Rev. 1.7 (11/17)
INSTALL FAUCET
COLONY SOFT
SINGLE CONTROL LAVATORY FAUCET
WITH SPEED CONNECT®DRAIN
INSTALLATION
INSTRUCTIONS
2175.503
Adjustable WrenchScrewdriver Channel Locks Tubing Cutter
Plumbers' Putty or Caulking
Certied to comply with ANSI A112.18.1M
CAUTION Turn off hot and cold water
supplies before begining.
CARE INSTRUCTIONS:
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
Fig. A.
Fig. B.
(HAND TIGHTEN)
3
1
2
4
3
PUTTY
• Apply a bead of putty along the edge of the underside of the FAUCET (1).
• Insert FAUCET (1) and CABLE CONNECTOR (2) through center hole
of mounting surface. Fig. A.
• From under side of mounting surface thread the two MOUNTING
NUTS (2) onto FAUCET SHANKS (4). Fig. B.
• Center FAUCET (1) and hand tighten MOUNTING NUTS (3) to
secure FAUCET (1).

- 2 -
2
M968882 Rev. 1.7 (11/17)
3INSTALL BLACK GASKET
• Remove CLEAR PLASTIC COVER (1). Remove
CARDBOARD SPACER (2) from under DRAIN
POP-UP (3). Fig. A.
• D r o p DRAIN BODY (4) through sink drain hole.
Make sure WHITE FOAM GASKET (5) is under
ange of DRAIN BODY (4). Fig. B.
Note: No plumber’s putty or caulk is required.
• T h e CABLE ATTACHMENT POINT (6) must
face towards the rear of the SINK. Fig. B.
INSTALL POP-UP DRAIN
4INSTALL GRAY LOCKNUT
• Install GRAY LOCKNUT (1) onto DRAIN BODY (2)
from below SINK. Fig. A.
Note: The at side of the GRAY LOCKNUT (1)
must face up.
• Tighten rmly by hand. No tools are required.
Check DRAIN FLANGE in SINK to ensure that
WHITE FOAM GASKET (3) is fully compressed
and not visible. Fig. B.
2
REAR OF
SINK
4
56
3
1
SINK
DRAIN
HOLE
Fig. A. Fig. B.
5POP-UP KNOB
• POP-UP KNOB (1) must be fully down.
FLAT SIDE OF GASKET
MUST FACE DOWN
1
2
Fig. A.
2
1
FLAT SIDE OF
GRAY LOCKNUT
MUST FACE UP
3WHITE FOAM
GASKET
NOT VISIBLE
DRAIN
FLANGE
Fig. B.
DOWN
1
• Install BLACK CONE GASKET (1) onto DRAIN BODY (2)
from below.
Note: The at side of the BLACK CONE GASKET (1) must
face down.

- 3 -
7
8
• Thread CABLE CONNECTOR (1) clockwise
onto DRAIN BODY CONNECTION (2) and
hand tighten. Fig. A.
Your new POP-UP DRAIN installation is
now complete. Fig. B.
Note: Tail piece on pop-up drain is
1-1/4" O.D. Fig. B.
• Operate LIFT KNOB (1) to verify that STOPPER (2) opens and
closes.
Note: If STOPPER (2) does not open and close properly then
refer to the “troubleshooting section” of these instructions.
CHECK OPERATION OF POP-UP
MAKE WATER SUPPLY AND WASTE CONNECTIONS
ATTACH CABLE CONNECTOR
6
M968882 Rev. 1.7 (11/17)
Fig. A.
2
1
1-1/4” O.D.
Fig. B.
2
1
HOT
COLD
FERRULE
COMPRESSION
NUT
COUPLING
NUT WITH
FAUCET
COUPLING
NUT ON FLEX
SUPPLIES
FLEXIBLE
SUPPLIES
1
3/8 O.D.
BULL-NOSE
RISERS
3/8 COMPRESSION
CONNECTION
2
3
4
“P” TRAP
NOTE: FLEXIBLE SUPPLIES OR BULL-NOSE RISERS NOT
INCLUDED AND MUST BE PURCHASED SEPARATELY.
• Connect water supply to INLET SHANKS (1) with 1/2" IPS
FLEXIBLE SUPPLIES (2) or 3/8" O.D. BULL-NOSE RISERS (3).
Use adjustable wrench to tighten connections. Do not over
tighten. Be careful not to kink copper supply when bending.
Use tubing cutter to cut to proper length.
• Connect HOT water supply to inlet of left SHANK and COLD
water supply to right SHANK using sealant, appropriate
connectors, and COUPLING NUTS.
• Connect 1-1/4" O.D. TAILPIECE (4) on POP-UP DRAIN
to “p” trap.

CARTRIDGE INLETS
MANIFOLD
1
2
3
4
M968882 Rev. 1.7 (11/17)
10
• With HANDLE (1) in OFF position, turn on WATER
SUPPLIES (2) and check all connections for leaks.
• Ensure that AERATOR (3) is tightened completely.
• Operate HANDLE (1) to allow water ow.
ADJUST HOT LIMIT STOP
TEST INSTALLED FITTING
9
3
2
5
2
“P” TRAP
WASTE
OUTLET
41
• Operate POP-UP KNOB (4) and ll lavatory with water.
Check that DRAIN STOPPER (5) makes a good seal
and retains water in Sink. If DRAIN STOPPER (5)
does not seal properly, please refer to Troubleshooting
section in these instructions.
• Release POP-UP KNOB (4) down and check all drain
connections and “P” trap for leaks. Tighten
if necessary.
CHECK DRAIN CONNECTIONS
HOT LIMIT SAFETY STOP ADJUSTMENT
By restricting handle rotation and limiting the amount of hot water allowed to mix with the cold, the HOT LIMIT SAFETY STOP
reduces risk of accidental scalding. To set the maximum hot water temperature of your faucets, all you need to do is adjust
the setting on the HOT LIMIT SAFETY STOP.
• Use a at blade screwdriver or your ngers to pull up and rotate red HOT LIMIT SAFETY STOP (1). Follow Step “A” or “B” to
adjust min./max. discharge temperature. “1” being the hottest to “8” the coldest temperature setting. Factory set at “1”.
- 4 -
11 SERVICE
PRY RED RING UPWARD
AND ROTATE
COUNTER-CLOCKWISE
"A"
ADJUSTMENT WHEN WATER IS TOO HOT
PRY RED RING UPWARD
AND ROTATE CLOCKWISE
"B"
ADJUSTMENT WHEN
WATER IS TOO COLD
"RED RING"- HOT LIMIT SAFETY STOP
"B"
"A"
TEMPERATURE
SETTING NUMBERS
If Faucet Drips Proceed As Follows
• Turn VALVE in OFF position.
• If faucet drips, operate handle several times from “off” to “on”.
Do not apply excessive force.
• Clogged CARTRIDGE INLETS may cause reduced ow in “full on” hot
or cold. To clean inlets, rst turn off water supply, then:
• Remove HANDLE (1), CAP (2) and CARTRIDGE (3).
• Clean CARTRIDGE INLETS and MANIFOLD.
• Reassemble CARTRIDGE (3), alternately tightening SCREWS (4).
Replace CAP (2) and HANDLE (1). Check ow.

M968882 Rev. 1.7 (11/17)
If sink does not hold water even though Stopper is in the “down” position:
• Follow CABLE ADJUSTMENT PROCEDURE.
If Stopper does not raise up fully or sink drains too slowly:
• Follow CABLE ADJUSTMENT PROCEDURE.
If you need to remove the Stopper:
• Follow STOPPER REMOVAL PROCEDURE.
If you would like the ability to remove your Stopper simply by lifting it out of the drain:
• Follow STOPPER INSTALLATION PROCEDURE for “Unlocked” mode.
Speed Connect®Drain
Troubleshooting Guide
• Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A.
• Look at the area on the Drain Body where the Cable was attached and locate the component labeled as
“Cam” in the illustration. Fig. B.
• Use a small screwdriver to rotate the Cam in the clockwise direction as far as it will go. At this point the
Stopper should be in the UP position. Fig. B, C.
• Push DOWN on the Lift-Knob to make sure it is fully down. Fig. C.
• Re-attach the Cable to the Drain Body Connection (2) by threading the Cable Connector (1) clockwise onto the
Drain Body Connection (2) and hand-tighten. Fig. A.
CABLE ADJUSTMENT PROCEDURE
1
2
CAM
CAM CAP
RE-ATTACH
DISCONNECT
Fig. A. Fig. B.
1
DOWN
STOPPER
Fig. C.
REMOVE
CAM CAP
REMOVE
CAM
Fig. D. Fig. F. Fig. E.
• Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A.
• Look at the area on the Drain Body where the Cable was attached and locate the component labeled
as “Cam” and “Cam Cap” in the illustration. Fig. B.
• Use ngers or small screwdriver under either side of the Cam Cap to pry it out from the Drain. Fig. D.
• Remove the Cam by pulling it straight out while wiggling gently to loosen the Rubber Seal. Fig. E.
• The Stopper can now be removed by lifting it out of the Drain. Fig. F.
STOPPER REMOVAL PROCEDURE
- 5 -

- 6 - M968882 Rev. 1.7 (11/17)
Unlocked Mode
Locked Mode
LOOP TOWARD
FRONT OF SINK
180˚
LOGO
DRAIN
Fig. H.
LOGO
DRAIN
Fig. G.
LOOP TOWARD
REAR OF SINK
Fig. J. Fig. K.
INSTALL
CAM CAP
CAM
INSTALL CAM
STOPPER INSTALLATION PROCEDURE
The Stopper can be installed two ways, “Locked” Mode (Stopper cannot be
removed) or “Unlock” Mode (Stopper is removable).
Locked Mode:
• Look at the Plastic Loop at the bottom of the Stopper and notice that the
Loop is on one side of the Stopper. Fig. G.
• T o install the stopper in “Locked” mode, insert the Stopper into the Drain so
that the Plastic Loop is facing toward the rear of the Sink and the American
Standard logo is facing front. Rotate Stopper slightly if necessary so that the
Stopper slides all the way down. Fig. G.
• Re-install the Cam into the Drain, rotating the Cam if necessary to make sure
it is fully inserted. Fig. J.
• Re-install the Cam Cap, making sure the guide teeth are facing outward. If
the Cam Cap does not “snap” into place, then rotate the Cam to make sure
it is fully inserted. Fig. K.
• Re-attach Cable. See “CABLE ADJUSTMENT PROCEDURE” in Troubling
Shooting Guide to complete installation. Stopper will be in “Locked” mode
and not be removable.
Unlocked Mode:
• Look at the Plastic Loop at the bottom of the Stopper and notice that the
Loop is on one side of the Stopper. Fig. H.
• T o install the stopper in “Unlocked” mode, insert the Stopper into the Drain
so that the Plastic Loop is facing toward the front of the Sink and the American
Standard logo is facing rear. Rotate Stopper slightly if necessary so that the
Stopper slides all the way down. Fig. H.
• Re-install the Cam into the Drain, rotating the Cam if necessary to make sure it
is fully inserted. Fig. J.
• Re-install the Cam Cap, making sure the guide teeth are facing outward. If the
Cam Cap does not “snap” into place, then rotate the Cam to make sure it is
fully inserted. Fig. K.
• Re-attach Cable. See “CABLE ADJUSTMENT PROCEDURE” in
“Troubleshooting Guide” to complete installation. Stopper will be in “Unlocked”
mode and removable.

- 7 - M968882 Rev. 1.7 (11/17)
COLONY SOFT
SINGLE CONTROL CENTERSET
LAVATORY FAUCET
WITH SPEED CONNECT®DRAIN
MODEL NUMBERS
2175.503
Replace the “YYY” with
appropriate finish code
POLISHED CHROME 002
BRASS 099
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 [phone]
Mon. - Fri. 8:00 a.m. to 8:00 p.m. EST
Saturday 10:00 a.m. to 4:00 p.m. EST
IN CANADA 1-800-387-0369
(TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-1200
M913208-007A
SPONGE WASHER
M962551-0070A
CAM ASSEMBLY
M962431-0070A
DRAIN MOUNTING KIT
M952430-0070A
CABLE ASSEMBLY
M952410-YYY0A
DRAIN ASSEMBLY
065800-0070A
ATTACHMENT NUT
M964463-YYY0A
AERATOR (1.2 GPM)
M922880-YYY0A
AERATOR (1.5 GPM)
M950158-0020A
LIFT ROD
M918506-0070A
CARTRIDGE SCREWS
M907301-YYY0A
CAP
M961627-YYY0A
HANDLE KIT
030746-0070A
HANDLE SCREW KIT
M962543-YYY0A
STOPPER
ASSEMBLY
M907265-0070A
PLUG BUTTON
M951471-0070A
CARTRIDGE