American Standard Selectronic 6055.105 User manual

Installation Instructions
(In Toronto Area only: 1-905-3061093)
Certified to comply with ASME A112.18.1M
© 2005 American Standard
To learn more about American Standard Faucets visit our website at: www.us.amstd.com or U.S.
customer's e-mail us at: [e-mail]
For Parts, Service, Warranty or other Assistance,
please call [phone] (In Canada: 1-800-387-0369)
NOTE TO INSTALLER: Please give this manual to the customer after installation.
(In Toronto Area only: 1-905-3061093)
Product No.'s & Options
Specifications
How to Install
Electrical Hook-up
Maintenance
FAQ,s
Replacement Parts
1
2
2-3
4-6
7-8
9-10
11
M968809R ev. 1. 7
6055.102
6055.105
6056.102
6056.105
6055.104 6056.104
6057.102
6057.105
6055.163
6055.165
6056.163
6056.165
6055.164 6056.164
6057.163
6057.165
6" GN Spout
Cast Spout
CAUTION: Use only American Standard
supplied cable sets. Using non-AS supplied
cables, or cutting, splicingor modifying any
components will void the warranty.
SELECTRONIC™
Proximity Faucets
Cast Spout and
Goose Neck Spout

5c. 10 ft. Extension Wire (for 6057 series)
6.Y-Connector
7. 4" Deck plate ( optional must be ordered separately)
8. 8" Deck plate ( optional must be ordered separately)
9. Mixing Valve ( optional must be ordered separately)
10. Key for vandal resistant aerator
11. 27" Extension Wire (for 6057 series)
1. Selectronic Spout Assembly
2. Mounting Kit
3. Electrical Enclosure
4. Supply Hose
5a. DC Battery (for 6055 series)
5b. AC Power Supply (for 6056 series)
All American Standard Faucets Are Water Tested At Our Factory.
Some Residual Water May Remain In The Faucet During Shipping.
Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years.To ensure
that your installation proceeds smoothly--please read these instructions carefully before you begin.
UNPACKING
How to order the Selectronic Product
1. Choose Power Supply 2. Choose Desired Spout • Single Hole Sink
• Single Inlet
• 1 and 3 Hole Sinks • Single Inlet
• 1 and 3 Hole Sinks • Hot and Cold Inlets
Base Product Deck Plate (optional) Mixing Valve (optional)
1. Remove the fitting and loose items from the carton. The illustration below shows the fitting and all loose items
after they have been removed from the carton. Some items may bepackaged partially assembled to other items.
1
605P400
605P800
605XTMV
6055.102
6055.104
6055.105
PRODUCT No.s PRODUCT No.s
6056.102
6056.104
6056.105
6057.102
6057.105
6055.163
6055.164
6055.165
6056.163
6056.164
6056.165
6057.163
6057.165
6
2
3
5a
5b
7
8
9
4
Deck Plate Mixing ValveBase Product
Cast Spout 6" GN Spout
M968809R ev. 1. 7
11
5c
1
10
DO NOT REMOVE PROTECTIVE
FILM FROM SENSOR EYE UNTIL
INSTALLATION IS COMPLETE.
DO NOT REMOVE PROTECTIVE
FILM FROM SENSOR EYE UNTIL
INSTALLATION IS COMPLETE.

TOOLS REQUIRED; Fig. 2 Fig. 2
1Channel Locks
2Adjustable Wrench
3Plumbers' Putty or Caulking
4Phillips Screwdriver
5Flat Blade Screwdriver
6Electric Drill & 1/4" Drill Bit
7Tape Measure
12
3
4
5
6
7
2
10'
Fig. 1
114mm
(4-1/2)
500mm
(20")
1524mm
(60)
381mm
(15)
3/8" COMP.
131mm
(5-1/8)
32mm (1-1/4)
125mm
(4-7/8)
81mm
(3-3/16)
49mm
(2)
141mm
(5-1/2)
11-1/8"
(284mm)
6-1/8"
(155mm)
MOUNTING
SURFACE
381mm
(15)
49mm
(2)
Roughing-in Dimensions
7"
(179mm)
GENERAL DESCRIPTION:
Electronic faucet with proximity operation. Vandal resistant solid brass
construction single post mounting. Operates on DC (battery) or AC
permanent power. In-line strainer for solenoid is integral. Single inlet 3/8
compression, built-in checks, and flexible stainless steel 15" reach inlet hose
for spout connection.
M968809R ev. 1. 7
CAUTION:Use only American Standard
suppliedcable sets. Using non-AS
suppliedcables, or cutting, splicing or
modifying any components will void the
warranty.
Note: All plumbing and electrical wiring must be installed in accordance with
applicable codes, regulations and standards.
INSTALL SPOUT ASSEMBLY;
Fig. 1
INSTALLATION
CAUTION Turn off hot and cold water
supplies before beginning
1
1. (Optional) Assemble DECK PLATE (1) and PUTTY
PLATE (2) to FAUCET BODY (3) with SCREW (4). Fig.1.
2. Connect the two 27" EXTENSION CABLES (5) to
the Faucet Sensor Cables. Fig. 1.
3. Insert 27" EXTENSION CABLES (5) , FLEX HOSE
(6) and SPOUT SHANK (7) through center hole of
mounting surface. Fig. 1a.
4. Assemble "C" WASHER (8) and LOCKNUT (10)
onto threads of SPOUT SHANK (7) from underside of
mounting surface. Fig. 1b.
5. Align FAUCET (3) and tighten LOCKNUT (10). If
using DECK PLATE (1) hand tighten DECK PLATE
SPIN NUTS (11) to secure FAUCET (3) to mounting
surface. Fig. 1b.
10
11
Fig. 1a Fig. 1b
5
7
7
6
8
3
1
1
2
2
Fig. 1
4
5
SENSOR
CABLES

Fig. 2
1. Determine location of ENCLOSURE (1). It must be
located with-in the 14" (356mm) by 21" (533mm)
shaded area shown in Figure 2 in order for electrical
connections from the spout assembly to be made.
NOTE: ENCLOSURE SUPPLY HOSE is 20". Distance
between wall supply and ENCLOSURE (1) must be
taken into consideration.
2. Remove 4 screws from COVER (2) and pull off
COVER (2). Hold the ENCLOSURE (1) in desired
location and mark the four mounting hole locations as
shown. Fig. 2.
NOTE: For AC installation see “AC VERSION; Fig. 2.”
Make power supply connection before mounting
ENCLOSURE (1) to wall.
3. The ENCLOSURE (1) works best if secured to a wall
stud or cross brace within the wall, using the SCREWS
(3) supplied. If the ENCLOSURE (1) is to be installed on
a tile or plaster wall the ANCHORS (4) and SCREWS
(3) should be used.
4. For installations on drywall or tiled walls; use
ANCHORS (4) and SCREWS (3) for securing
ENCLOSURE (1) to finished wall. Drill four 1/4" dia.
holes a minimum of 1-3/4" deep. Insert the four
ANCHORS (4) flush with face of the finished wall.
Align the ENCLOSURE (1) and Install the MOUNTING
SCREWS (3). Tighten to secure ENCLOSURE (1) to
mounting surface.
1524mm
(60)
14"
(356mm)
3-3/4"
(96mm)
2-3/4"
(71mm)
3"
(76mm)
21"
(mm)
2
4
3
1
1
1
20"
(500mm)
MOUNTING HOLES
SUPPLIES
WASTE
ENCLOSURE
MOUNTING
HOLES
LAVATORY RIM OR
MOUNTING SURFACE
3
NOTE: If using Mixing Valve (optional) See Sheet
#M968808 for installation instructions.
MOUNT ENCLOSURE; Fig. 2
2
1. Connect SUPPLY NUT (1) from spout assembly to
nipple on top of ENCLOSURE (2). Tighten with
adjustable wrench to make a water tight connection.
Fig. 3.
NOTE; If using the optional Mixing Valve See Sheet
#M968808 for installation instructions.
CONNECT SPOUT HOSE TO
ENCLOSURE; Fig. 3
CONNECT WATER SUPPLY TO
ENCLOSURE AND WALL SUPPLY;
Fig. 4
3
Fig. 3
4
1
2
1
3
3
Fig. 4
2
1. Insert FIBER WASHER (4) into SUPPLY NUT (1) on
ENCLOSURE (2).
2. Connect SUPPLY NUT (1) on ENCLOSURE (2) to
FLEXIBLE SUPPLY HOSE (3). Tighten to make a
water tight connection. Use two wrenches to tighten if
necessary. Fig. 4.
3. Connect FLEXIBLE SUPPLY (3) directly to wall supply.
Connection on FLEXIBLE SUPPLY (3) is 3/8"
compression. Use adjustable wrench to tighten
connection. Do not over tighten. Fig. 4a.
Note: FLEXIBLE SUPPLY (3) measures 20" from the
bottom of the ENCLOSURE (1) base. If additional
supply length is required, installer must purchase parts
separately.
Important: If FLEXIBLE SUPPLY (3) is too long, loop to
avoid kinking.
COLD WATER OR
TEMPERED
WALL SUPPLY
Fig. 4a
4
M968809 Rev.1.7

M968809 Rev.1.7
4
1. Remove ENCLOSURE COVER (1). Fig. 1.
2. Feed the EXTENSION CABLES (2) from the Faucet
through the top of ENCLOSURE (3). Fig. 1a.
3. Install BATTERY (4) if not already installed, make
sure the shape of the BATTERY (4) follows the shape of
the BATTERY HOLDER (5). Fig. 1b.
4. Insert the BATTERY CONNECTOR (5a) through
GROMMET (6) as shown. Fig. 1c.
5. Connect SOLENOID CABLE (7) and BATTERY
CONNECTOR (5a) to EXTENSION CABLES (2) from
Faucet Sensor. Fig. 1d.
6. Replace ENCLOSURE COVER (1). Tighten cover
screws firmly.
DC VERSION (BATTERY); Fig. 1
1
ELECTRICAL INSTALLATION
Fig. 1a Fig. 1b
Fig. 1
Fig. 1c
5a
7
2
Fig. 1d
2
3
1
4
5
INSTALL BATTERY
CR-P2
5a
5a
6
5
CAUTION: Use only American Standard supplied
cable sets. Using non-AS supplied cables, or
cutting, splicing or modifying any components will
void the warranty.

5M968809 Rev.1.7
AC VERSION; Fig. 2
2
CAUTION Before opening ENCLOSURE
disconnect AC power supply.
NOTE: For AC installation see Fig. 2b.
Make power supply connection before mounting
ENCLOSURE (1) to wall.
1. Remove ENCLOSURE COVER (1). Fig. 2.
2. Feed the EXTENSION CABLES (2) from the Faucet
through the top of ENCLOSURE (3). Fig. 2a.
3. Remove SPLIT PLUG (4) from POWER SUPPLY
GROMMET (5). Insert POWER CORD (7) into SPLIT
PLUG (4). Insert POWER CORD CONNECTOR (6)
through POWER SUPPLY GROMMET (5). Push SPLIT
PLUG (4) into POWER SUPPLY GROMMET (5) to seal.
Fig. 2b.
4. Insert POWER CORD CONNECTOR (6) through
GROMMET (8) as shown.
5. Connect SOLENOID CABLE (9) and POWER CORD
CONNECTOR (6) to EXTENSION CABLES (2) from
Faucet Sensor. Fig. 2d.
6. Replace ENCLOSURE COVER (1). Tighten cover
screws firmly.
Fig. 2a
Fig. 2
Fig. 2c
6
9
2
Fig. 2d
2
3
4
7
5
Fig. 2b
6
1
6
8

M968809 Rev.1.7
FOR AC-VERSION
(MULTI HOOK-UP); Fig. 3, 3a, 3b
3
NOTE: For AC installation see “AC VERSION; Fig. 2b.”
Make power supply connection before mounting
ENCLOSURE (1) to wall.
1. Remove COVERS from all ENCLOSURES (2). Fig. 3.
2. Remove SOLID BLACK INSERT (5) from left side of all
ENCLOSURES (2), except from Unit #1. Replace with
GRAY GROMMET (9). (Supplied with each Faucet). Fig. 3.
3. All Units: Connect the two 27" EXTENSION CABLES
(4) to the Faucet Sensor Cables. Feed the 27"
EXTENSION CABLE CONNECTORS (1, 1a) from the
Faucet through the top of ENCLOSURE (2). Fig. 3a.
4. Connect one 27" EXTENSION CABLE (1) to the
SOLENOID (3). Fig. 3, 3a. Connect the second 27"
EXTENSION CABLE (1a) to the top of the
Y-CONNECTOR (8).
5. Connect the 10 ft. EXTENSION CABLE (6) to the top of
the Y-CONNECTOR (8). Feed the other end through the
two GRAY GROMMETS (9) and connect to the bottom of
the next Y-CONNECTOR (8). Place Y-CONNECTOR (8)
into ENCLOSURE (2) as shown Fig. 3a, 3b.
6. Repeat Steps above for each additional Unit, for a Max.
of 15 Units on one POWER SUPPLY (7). Fig. 3.
7. Replace ENCLOSURE COVERS. Tighten cover screws
firmly.
6
Unit #1
Unit #1
Unit #2 Unit #3
Fig. 3
Fig. 3a
1a
8
6
AC POWER SUPPLY
AC POWER
SUPPLY
10 ft. EXTENSION
CABLE
10 ft. EXTENSION
CABLE
FAUCET WIRE
CONNECTORS
4
SENSOR
CABLES
3
7
2
1
5
5
6 6 6
8 8
9
5
9
FAUCET WIRE
CONNECTORS
FAUCET WIRE
CONNECTORS
6
6
8
9
Fig. 3b
*MAXIMUM OF 15 UNITS PER AC POWER SUPPLY.
10' MAXIMUM CABLE LENGTH BETWEEN UNITS.

MAINTENANCE
When the Sensor detects a user, the water
immediately starts to flow. Water flow will stop Two
seconds after user is out of sensor range. The off delay
allows the user to comfortably move his hands without
the flow cycling on to off. As a precaution, a safety
timer will turn off the water, after the sensor has been
blocked for 59 seconds. The water will stay off until the
blockage is removed from the detection zone.
Detection Zone: 2" - 10" (50mm - 250mm)
Default: Set at Factory 6" (150mm)
HANDWASH SENSOR OPERATION;
Fig. 1
1
1. Remove COVER from ENCLOSURE (1). Fig. 3.
2. Remove old BATTERY (2). Install new BATTERY (3)
making sure the terminal side is inserted first and
shape of the battery follows the shape of the
BATTERY HOLDER (4). Fig. 3.
3. Replace ENCLOSURE COVER. Tighten cover
screws firmly. Fig. 3.
HOW TO INSTALL AND CHANGE
BATTERY; Fig. 3
3
1. Setting the Detection Zone (Distance):
Remove cover from ENCLOSURE. Disconnect Power
Supply (1), then reconnect. Fig. 2.
2. While the SENSOR CONTROL LED (2) is blinking
slowly, place your hand 1 - 2 in. (30-50mm) in front of
the sensor. Fig. 2a.
3. When the LED stops blinking and stays "ON", move
your hand to the desired position and hold in place until
the LED begins to blink again. Fig. 2a.
4. Once the SENSOR CONTROL LED (2) begins to
blink again, remove your hand from the detection zone.
When the flashing stops, the detection distance is set.
5. Replace ENCLOSURE COVERS (2). Tighten cover
screws firmly.
HOW TO CHANGE SENSOR
RANGE; (Factory set at 6") Fig. 2
2
Fig 1
7
Fig.3
DETECTION
ZONE
Fig. 2
Fig. 2a
1" - 2" (30mm - 50mm
BLINKING LED
UP TO 10" (250mm)
BLINKING
LED
2
2
M968809 Rev.1.7
1
CR-P2
CR-P2
4
1
6
2
3

8
1. Remove AERATOR HOUSING (1) with KEY supplied
with faucet.
3. Remove AERATOR (2) from HOUSING (1).
2. Clean the AERATOR SCREENS (3) with a old tooth
brush to remove dirt.
4. Rinse Clean with water. Reassemble and install into
spout end. Be sure black seal washer is in place.
HOW TO CLEAN AND REMOVE
THE AERATOR; Fig. 5
5
2
3
Fig.5
1. Remove ENCLOSURE COVER.
2. Close SUPPLY STOP (1) with 4mm Hex wrench.
Note: Keep water flowing out of faucet while shutting off.
3. Unthread STRAINER (2) using a 7/16" socket.
4. Pull out the STRAINER (2) and clean with an old
toothbrush. Rinse thoroughly with water.
5. Install the STRAINER (2) back in its place and
tighten with a 7/16" socket.
Caution: do not over tighten strainer.
Note: It is recommended to clean strainer every 6
months.
6. Open SUPPLY STOP (1) with 4mm Hex wrench.
7. Replace ENCLOSURE COVER. Tighten cover
screws firmly.
HOW TO CLEAN FILTER; Fig. 4
4
Fig.4
CAUTION Before opening ENCLOSURE
disconnect AC power supply.
1
Fig.5
HOW TO CONVERT RIGID GOOSE
NECK SPOUT TO SWING SPOUT
Fig. 6
The GN SPOUT is shipped from the factory as a
rigid assembly. To convert the GN SPOUT into a
SWING SPOUT proceed as follows:
1. Remove SET SCREW (1) from back of GN SPOUT
(2) with a flat blade screwdriver. Fig. 6.
2. Install SWIVEL SET SCREW (3) into opening in the
GN SPOUT (2). SWIVEL SET SCREW (3) is found in
hardware bag within product box.
6
Fig.6
1
2
3(USE SHORT
SET SCREW
FOR SWIVEL
SPOUT)
M968809 Rev.1.7
3
1
2
7/16" SOCKET
CLEAN
SCREENS
4mm HEX WRENCH

FAQ'S
Q: How will I know if battery needs to be replaced?
A: Valve does not open and sensor blinks 2 times
interrupted by pause for up to 7 days.
Q: Why has the flow rate of the faucet reduced
significantly?
A: Check and clean aerator and strainer.
Q: There is no flow out of faucet when I'm in the
sensor range?
A: Check sensor. If sensor blinks 2 times interrupted by
pause, replace battery, or call [phone].
Q: Why does the faucet operate the opposite of
expected-Turns On when not in sensor range, but turns
off when in sensor range?
A: Sensor wires to solenoid are reversed.
Q: What is the normal operating pressure range?
A: Faucet will operate with supply pressures ranging
from 20-80 psi.
9
CAUTION
GENERAL CLEANING; Fig. 7
1. For general cleaning use a damp, soft cloth to clean
the spout and the sensor.
2. For cleaning dirt use a soft cloth with diluted dish
washing detergent. Wipe the area using a wet cloth
and dry using a soft cloth.
Do not scratch the sensor when cleaning.
Avoid using anything that may scratch the spout
surface. Never use polishing power, detergent or a
nylon scrub brush. They will damage the surface of the
spout or Sensor.
7
Fig.7
M968809 Rev.1.7