American Standard VORMAX PLUS Maintenance manual

17302351-100 Rev. A 8/17
SAVE FOR FUTURE USE
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2017
INSTALLATION INSTRUCTIONS
CARE AND MAINTENANCE
TANK
BOWL
Bolt Caps (2)
Bowl-To-Floor
Knobs (2)
T-Bolts with
Retainer (2)
EZ-INSTALL KIT
INCLUDED WITH BOWL
EZ-INSTALL INLET VALVE
COUPLING KIT
EZ-INSTALL KIT
INCLUDED WITH TANK
VORMAX PLUS TOILET SEAT AND FRESHINFUSER PACKAGE
Attachment Handle Nuts (3)
Before You Start:
Before installing your toilet, please see your product spec page to verify the dimensions and water supply
connections. Visit our website where you can search by Model number for the product spec page at:
http://www.americanstandard-us.com/
For Assistance Call Customer Care at: [phone]
Wax Ring
Water Supply Line
SOLD SEPARATELY
Nuts (2)
Washers (4)
Base Plate
Base Plate
Housing
VorMax Plus
FreshInfuser™
2 Packs
Rubber Grommets (2)
Toilet Seat
Long Bolts (2)
NOTE: These instructions are specically for installing the VorMax Plus seat and FreshInfuser package only.
Refer to the appropriate VorMax toilet installation manual packed inside the tank for the toilet installation.
VorMax Toilet Installation Instructions:
See separate installation document located in tank package.
IMPORTANT: Do not connect the water supply line until you have completed
the VorMax Plus seat and FreshInfuser Installation procedure.
VORMAX PLUS TOILET SEAT AND
FRESHINFUSER PACKAGE

2
7302351-100 Rev. A 8/17
2
1
Assembly of Housing Base Plate
Read carefully then remove CAUTION sticker (1)
next to spud (2) from rear of bowl.
3
2
1
Insert rubber grommets
(3) (narrow end rst) up
underneath the bowl
and into each seat
mounting hole. Ensure
grommets stay in place
in bowl.
Check that rubber gasket is rmly
attached to the underside of the base
plate (1) and place plate over Spud (2)
and rear of bowl while aligning the two
mounting holes through the bowl.
123
456
From above, install mounting screws and
washers (1) through each hole, then place
rubber washer (2) and plastic nut (3) from
underneath onto each bolt. Snug down but
do not fully tighten.
1
2
!
CAUTION :IF A VORMAX PLUS FRESHINFUSER IS NOT SECURELY INSERTED INTO THE SPUD OPENING , DO
NOT FLUSH THE TOILET AS THIS MAY RESULT IN WATER LEAKING FROM THE TOILET. TOILET MUST HAVE A
VORMAX PLUS FRESHINFUSER INSERTED IN THE SPUD OPENING AT ALL TIMES WHEN FLUSHING THE TOILET.
For further assistance please call Customer Care at: [phone]
Place seat onto the protruding Base Plate Posts
and press in to “click” into place, close seat and
cover and align seat with bowl. Once aligned,
further tighten seat nuts under bowl to securely
hold seat in position.
Remove seat by pressing both inside buttons
to release seat and cover:
Seat Alignment
Open the seat and cover. Push both inside
buttons to release seat and cover. Pull the seat
and cover upwards to take it off the hinges.
Install VorMax Plus Housing (1) onto
VorMax Plus Base Plate (2), snap in
to secure.
Open Base Plate Housing Door (1). Observe the
marked notch on the VorMax Plus FreshInfuser
(2). Observe the same marked notch located on
the Base Plate Housing.
Before installing, line up the marked notches on
the Base Plate Housing and the VorMax Plus
FreshInfuser.
Insert the VorMax Plus FreshInfuser into the spud
opening aligning the marked notch on the VorMax
Plus FreshInfuser and the Base Plate Housing.
Marked Notch
on VorMax Plus
FreshInfuser
Notch on Base
Plate Housing
Door
UNLOCKED
Marked Notch
on VorMax Plus
FreshInfuser
Notch on Base
Plate Housing
Door
2
2
1

37302351-100 Rev. A 8/17
!
CAUTION :IF A VORMAX PLUS FRESHINFUSER IS NOT SECURELY INSERTED INTO THE SPUD OPENING , DO
NOT FLUSH THE TOILET AS THIS MAY RESULT IN WATER LEAKING FROM THE TOILET. TOILET MUST HAVE A
VORMAX PLUS FRESHINFUSER INSERTED IN THE SPUD OPENING AT ALL TIMES WHEN FLUSHING THE TOILET.
For further assistance please call Customer Care at: [phone]
Turn on water supply.
A
Connect water supply
line. (Sold separately)
Hand tighten nut.
B
Place seat back onto the
back plate posts and press
to “click” into place.
CAUTION : IF A VORMAX PLUS FRESHINFUSER IS NOT
SECURELY INSERTED INTO THE SPUD OPENING, DO
NOT FLUSH THE TOILET AS THIS MAY RESULT IN
WATER LEAKING FROM THE SPUD OPENING.
TOILET MUST HAVE A VORMAX PLUS FRESHINFUSER
INSERTED IN THE SPUD OPENING AT ALL TIMES
WHEN FLUSHING THE TOILET.
!
!
!
9
WARNING: Overtightening of water supply line nuts could result in breakage and potential flooding. If the
connection leaks after hand tightening, replace the supply line. If the connection continues to leak with
the new supply line, replace the fill valve. Do not use any type of sealant on the water supply connection.
Use of plumber’s putty, pipe dope, or any other type of sealant will void the warranty.
Clockwise
Direction
Clockwise
Direction
Locked Position
LOCKED
TURNING TO LOCK
Locked
Position
1
Turn VorMax Plus FreshInfuser (1) in a clockwise direction
(following arrow direction) until it stops at the “Lock” symbol
approximately 1/4 turn.
1
WARNING: Ensure that the VorMax Plus FreshInfuser is
correctly aligned when inserted. If it is not correctly aligned
water could leak from the opening.
!
8
7

4
7302351-100 Rev. A 8/17
VorMax®Plus technology infuses Lysol®cleaner into the water with each
ush, freshening the bowl day after day. Its powerful VorMax®jetted scrub
allows Lysol®cleaner to scrub the entire bowl, including under the
CleanCurve™Rim. The VorMax Plus FreshInfuser™is hidden in a
compartment and easy to access. Unlike competitive products, there’s
nothing unsightly hanging inside of the bowl. Each VorMax Plus
FreshInfuser™lasts 30 days and exudes an ocean fresh scent. Daily use of
the VorMax®Plus toilet offers continuous freshness, ush after ush.
• Two VorMax Plus FreshInfuser™included with the purchase of your toilet
• Each VorMax Plus FreshInfuser™pack freshens up to 30 days (about 360 ushes).
• Ocean Fresh Scent
• VorMax Plus FreshInfuser™packs for purchase available online at:
https://www.americanstandard.com/VorMaxPlus
or at participating supply houses and retailers.
HOW IT WORKS
VorMax Plus FreshInfuser™
Problem Possible Cause Corrective Action
Water leaks around
VorMax Plus
FreshInfuser
a. VorMax Plus FreshInfuser not inserted into Spud correctly
b. Rubber gasket around VorMax Plus FreshInfuser is
damaged or missing
c. No FreshInfuser inserted in spud
a. Remove VorMax Plus FreshInfuser and reinsert.
Reference steps 6 and 7
b. Replace VorMax Plus FreshInfuser
c. Insert VorMax Plus FreshInfuser
Bowl not as clean
as it should be
a. VorMax Plus FreshInfuser cleaner pack is empty a. Replace VorMax Plus FreshInfuser
Troubleshooting Guide for VorMax Plus FreshInfuser
™
Care and Cleaning
When cleaning your toilet seat wash it with a mild, soapy water: rinse the seat thoroughly with clear water and dry with a soft cloth.
Avoid detergents, disinfectants, or cleaning products in aerosol cans. Never use abrasive scouring powders on your seat. Some
bathroom chemicals and cosmetics may damage the seat’s finish. After installation, check the tightness of the bolts from time to
time to ensure a tight fit.
In the United States:
American Standard Brands
1 Centennial Ave
Piscataway, New Jersey 08854
Attention: Director of Customer Care
For residents of the United States, warranty
information may also be obtained by calling
the following toll free number: [phone]
www.americanstandard.com
In Canada:
AS Canada, ULC
5900 Avebury Rd.
Mississauga, Ontario
Canada L5R 3M3
Toll Free: [phone]
www.americanstandard.ca
In Mexico:
American Standard B&K Mexico
S. de R.L. de C.V.
Via Morelos #330
Col. Santa Clara
Ecatepec 55540 Edo. Mexico
Toll Free: 01-800-839-1200
www.americanstandard.com.mx
LYSOL® is used under license to American Standard. © 2017