American Standard SELECTRONIC 6065.22X User manual

Installation Instructions
Installation Instructions
(In Toronto Area only: 1-905-3061093)
Certified to comply with ASME A112.19.2M
© 2010 AS America, Inc.
NOTE TO INSTALLER: Please give this manual to the customer after installation.
SELECTRONIC™
PROXIMITY TOILET
CONCEALED FLUSH VALVE
1.28 & 1.6 GPF
Concealed Flushometer
for 1-1/2"Top or Back Spud Bowls
CLOG RESISTANT
ONE SENSOR FITS ALL
M968550 REV. 1.5
To learn more about American Standard Faucets visit our website at: www.americanstandard-us.com
or U.S. customer's e-mail us at: [email protected]
For Parts, Service, Warranty or other Assistance,
please call 1-800-442-1902 (In Canada: 1-800-387-0369)
(In Toronto Area only: 1-905-3061093)
6065.22X
6067.22X
6068.22X
MODEL NUMBERS
6065.26X
6067.26X
6068.26X
• Self-cleaning piston valve prevents clogging and reduces maintenance.
• Only 1 sensor for entire Selectronic™ line of faucets, urinals, and
ush valves.
• Range can be adjusted manually or with optional remote control.
• Sensor Features Low Battery Indicator.

All American Standard Products Are Water Tested At Our Factory.
Some Residual Water May Remain In The Valve During Shipping.
Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years.To ensure that your
installation proceeds smoothly--please read these instructions carefully before you begin.
UNPACKING
1. Remove the Flush Valve items from the carton. The illustration below shows all items after
they have been removed from the carton. Some items may be packaged partially assembled to
other items.
9
8a
1
3
2
4
7c
7a
7b
5
DO NOT REMOVE PROTECTIVE FILM FROM SENSOR
EYE UNTIL INSTALLATION IS COMPLETE.
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
CARE INSTRUCTIONS FOR CHROME PLATED ITEMS:
7c. Vacuum Breaker Flush Connection
(Top Spud)
8a. AC Power Supply [Model# 6067]
8b. DC Power Supply
8c. 10’ Extension Wire for Multi-AC
9. Installation Instructions
1. Flush Valve Assembly
2. Electrical Box
3. Cover Plate with Sensor
4. Supply Stop
5. Sweat Solder Adapter
6. Manual Override Hoses
7a. Vacuum Breaker Flush Connection
(Wall-Mount Back Spud)
7b. Vacuum Breaker Flush Connection
(Floor-Mount Back Spud)
TOP
8b 8c
1
6
Installation Instructions
Installation Instructions
(In Toronto Area only: 1-905-3061093)
Certified to comply with ASME A112.19.2M
© 2009 AS America, Inc.
NOTE TO INSTALLER: Please give this manual to the customer after installation.
SELECTRONIC™
PROXIMITY TOILET
CONCEALED FLUSH VALVE
1.28 & 1.6 GPF
Concealed Flushometer
for 1-1/2"Top or Back Spud Bowls
CLOG RESISTANT
• Self-cleaning piston valve prevents clogging and reduces maintenance.
ONE SENSOR FITS ALL
• Only 1 sensor for entire Selectronic™ line of faucets, urinals, and
ush valves.
• Range can be adjusted manually or with optional remote control.
• Sensor Features Low Batter y Indicator.
M968550 REV. 1.5
To learn more about American Standard Faucets visit our website at: www.americanstandard-us.com
or U.S. customer's e-mail us at: [email protected]
For Parts, Service,Warranty or other Assistance,
please call 1-800-442-1902 (In Canada: 1-800-387-0369)
(In Toronto Area only: 1-905-3061093)
6065.22X
6067.22X
6068.22X
MODEL NUMBERS
6065.26X
6067.26X
6068.26X
M968550 REV. 1.5

RECOMMENDED TOOLS; Fig. 2 Fig. 2
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
Teflon Tape
Flat Blade Screwdriver
Adjustable Wrench
Tape Measure
Hacksaw
Tubing Cutter
File
For Sweat Connection; Solder and Torch
2.5mm Hex Wrench
1.5mm Hex Wrench
123
4
5
6
7910
8
PRIOR TO INSTALLATION
Note: Prior to installing the Selectronic™Flush Valve
the following items must be installed.
1. Water Closet
2. Drain line
3. Water supply line
• Flush all water lines prior to operation (See Step 4). Dirt
and debris can cause flush valve to run continuously.
• With the exception of Supply Stop Inlet, DO NOT use pipe
sealant or plumbing grease on any valve component or
coupling!
• Protect the chrome or special finish on chrome plated
items.
DO NOT USE toothed tools on finished surfaces to install or
service these valves. Also see “Care and Cleaning” section
of this manual.
• This product contains mechanical and/or electrical
components that are subject to normal wear. These
components should be checked on a regular basis and
replaced as needed to maintain the valve’s performance.
IMPORTANT:
• All plumbing must be installed in accordance with
applicable codes and regulations.
• Water supply lines must be sized to provide an
adequate volume of water for each fixture.
2
Fig. 1
Roughing-in Dimensions GENERAL DESCRIPTION:
10'
Concealed Flushometer
for 1-1/2" Spud Fixtures
SELECTRONIC™
PROXIMITY TOILET
FLUSH VALVE
Exclusive, self cleaning piston-type flush
valve with proximity operation and manual
override. Operates on DC (batte r y)or
AC power. Recommended operating
pressure 25psi (flowing) to 80 psi (static).
Can install left or right-handed. Detection
Zone can also be adjusted manually, or
with optional remote control.
-C-L- 51mm (2)
+ WALL THICKNESS
51mm
(2)
152mm
(6) MIN.
71mm
(2-3/4) DIA.
483mm
(19) MAX.
25mm (1) MAX.
160mm
(6-1/4)
OVERRIDE
BUTTON
160mm
(6-1/4)
406mm
(16)
127X127mm
(5X5 CUTOUT
FOR BOX)
127mm
(5) MAX.
432mm
(17 MAX.)
19mm
(3/4.)
289 TO 403mm
(11-3/8 MIN. TO
15-7/8 MAX.)
*FOR LOCATION OF INLET
SUPPLY ON BACK INLET
FIXTURES,REFER TO FIXTURE
BEING INSTALLED
FOR CORRECT HEIGHT FROM
FINISHED FLOOR
73 TO 137mm
(2-7/8)MIN. TO
(5-3/8) MAX.
403 TO 441mm
(15-7/8) MIN. TO
(17-3/8) MAX.
FINISHED WALL
CONCEALED BACK
SPUD TOILET
EXPOSED BACK
SPUD TOILET
TOP SPUD
TOILET
TOP SPUD
TOILET
TOP OF
FIXTURE
SENSOR
SUPPLY
DN 25mm
(1) I.P.S.
115mm-134mm
(4-1/2 TO 5-1/4)
*Note: The Critical Line (-C-L-) on Vacuum
Breaker must typically be 6"(152mm) min.
above fixture. Consult Codes for details.
73 TO 111mm
(2-7/8 TO
4-3/8) 292mm
(11-1/2) MAX.
51mm
(2)
51mm
(2)
-C-L-
*
WALL THICKNESS
MAXIMUM
DETECTION ZONE
400mm-800mm
(15-3/4 TO 31-1/2)
15˚
19mm
(3/4.)
TOP OF
FIXTURE
M968550 REV. 1.5

Fig. 4
Fig. 3a
Fig. 5
3
INSTALL ELECTRICAL BOX
ASSEMBLY; Fig. 3
1. Cut a 127x127mm (5"x 5") opening in finished wall for
ELECTRICAL BOX (1) at the deminsion shown in Fig.3.
2. Rotate the 4 MOUNTING TABS (2) flat against the
electrical box. Holding the MOUNTING TABS (2) in
position install the ELECTRICAL BOX (1) into the opening.
Make sure the MOUNTING TABS (2) are behind the wall.
3. Tighten the the 4 MOUNTING SCREWS (3) until the
ELECTRICAL BOX (1) is almost secure in the wall.
Before tighting fully rest a level at the top edge of the
ELECTRICAL BOX (1) and make sure the box is level,
then tighten fully. Fig. 3a.
4. *Cut a 2" hole for supply to fixture at deminsion shown.
1
Fig.3 (TOP SPUD FIXTURE ILLUSTRATED)
1
3
2
2
1
1
1. Open SUPPLY STOP (1).
3. Turn on water supply to flush line of any debris or
sediment.
4. Close SUPPLY STOP (1) and turn off water supply line.
FLUSH OUT SUPPLY LINES; Fig. 5
3
*FOR HOLE LOCATION OF
SUPPLY ON BACK INLET
FIXTURES, REFER TO FIXTURE
BEING INSTALLED FOR CORRECT
HEIGHT FROM FINISHED FLOOR
127mm
(5)
406mm
(16 REF.)
127mm
(5)
INSTALL SWEAT SOLDER
ADAPTER; Fig. 4
CAUTION Turn water supplies off
before beginning
Note: Control stop inlet is 1" IPS. For optional sweat
connection, install Sweat Solder Adapter (1) (Supplied)
for 1" copper pipe supply line. Fig. 4.
1. Clean the end of the supply pipe. Push the threaded
ADAPTER (1) on until it is seated against the internal
stop. Sweat the ADAPTER (1) to the pipe.
2. From behind the wall install the CONTROL STOP (2)
to the water supply line with the outlet positioned as
required.
3. Support piping as required.
2
TOP
FILE
EDGES
CLEAN & SOLDER
TO ADAPTER (1)
115mm-134mm
(4-1/2 TO 5-1/4)
CONTROL STOP
DN 25mm
(1" I.P.S.)
CONTROL
STOP
OUTLET
CLOCKWISE CLOSES
CONTROL STOP
COUNTER-CLOCKWISE
OPENS CONTROL STOP
TOP
TOP
2
403 TO 441mm
(15-7/8 MIN. TO
17-3/8 MAX.)
127mm
(5 MAX.)
M968550 REV. 1.5

4
Fig. 6
Fig. 6a
Fig. 6b
Fig. 6c
3
4 INSTALL VACUUM BREAKER AND
FLUSH CONNECTIONS; Fig. 6
4
1. Place the SPUD FLANGE (1) over the spud on the
Fixture. Fig. 6.
2. Thread SPUD COUPLING NUT (2) onto Spud. Make
sure SEAL WASHER (4) and FRICTION WASHER (3)
are installed. Do not tighten fully. Fig. 6.
3. Remove the COUPLING NUTS (6, 6a) from the
CHROME ELBOW (5). Make sure you have a TAPERED
RUBBER WASHER (7), PLASTIC SUPPORT (8) and
SQUARE SEAL WASHER (9). Fig. 6a.
4. Install the SQUARE SEAL WASHER (9) onto the
PLASTIC SUPPORT (8) if not already installed. Insert
the PLASTIC SUPPORT (8) into the DOWN TUBE (10).
Slide the COUPLING NUT (6) onto the DOWN TUBE
(10).Connect the COUPLING NUT (6) to the
CHROME ELBOW (5) and tighten fully. Insert the
DOWN TUBE (10) with CHROME ELBOW (5) into the
SPUD COUPLING NUT (2) and push it down. Do not
tighten fully. Fig. 6a. Note: If center line of ELBOW
(5) cannot be adjusted to line up with hole in wall,
then cut the DOWN TUBE (10) as required.
5. Measure and cut the HORIZONTAL TUBE (11) to
length required. Important: Make sure that there is a
minimum of 1-1/4" for engagement with elbow when
making your measurement. Fig. 6b.
6. Remove the COUPLING NUT (14) from BRASS
ELBOW (12) and slide it onto the HORIZONTAL
TUBE (11). Install the SQUARE SEAL WASHER (13)
onto the PLASTIC SUPPORT (15) if not already
installed. Insert the PLASTIC SUPPORT (15) into the
HORIZONTAL TUBE (11). Connect the COUPLING
NUT (14) to the BRASS ELBOW (12) and tighten fully.
Fig. 6b.
7. From behind the wall install the ELBOW AND TUBE
ASSEMBLY (12, 11) through the hole in the wall. Install
WALL ESCUTCHEON (16) onto HORIZONTAL TUBE (11).
Assemble the COUPLING NUT (6a) and TAPERED
RUBBER WASHER (7) in the CHROME ELBOW (5) onto
the HORIZONTAL TUBE (11).Push the HORIZONTAL
TUBE (11) into the CHROME ELBOW (5). Tighten
COUPLING NUT (6a) but not fully. Fig. 6b.
8. For back spud installations: Follow steps #1 and #2
to install the spud coupling kit. Push the HORIZONTAL
TUBE (11) into the spud connection on the back of the
fixture. Do not tighten fully. If spud coupling kit is not
required install HORIZONTAL TUBE (11) into back
spud on fixture and hand tighten. Fig. 6b.
9. All installations: If required cut scored VACUUM
BREAKER PIPE (17) to fit, leave a minimum of 1-1/4"
(32mm) of pipe to ensure engagement with
compression coupling. Assemble the COUPLING NUT
(18) and TAPERED RUBBER WASHER (19) in the
BRASS ELBOW (12) onto the VACUUM BREAKER
PIPE (17). Install VACUUM BREAKER PIPE (17) into
BRASS ELBOW (12) and hand tighten COUPLING
NUT (18). Fig. 6c.
Note: If cutting VACUUM BREAKER PIPE (16) to
size, note that Critical Line (C/L) on Vacuum
Breaker must typically be 6"(152mm) above fixture.
Consult Code for details.
1
2
34
1-1/2" TOP SPUD
9
14
16
12
11
15
5
7
6a
13
6a
8
7
5
6
10
FLANGE END UP
FLANGE END
11
18
19
19
17
TOP SPUD
INSTALLATION
BACK SPUD
INSTALLATION
BACK SPUD
INSTALLATION
TOP SPUD
INSTALLATION
2
M968550 REV. 1.5
TAPERED SIDE
TAP E RED
SIDE
12
TAPERED SIDE UP
TAP E RED
SIDE UP

7
9
6
25
810
Fig. 9
Fig. 8
5
7
1. Insert the side ADJUSTABLE TAILPIECE (1) on the
FLUSH VALVE (2) into the SUPPLY STOP (3).
Lubricate the TAILPIECE O-RING (4) with water if
necessary. Lightly tighten COUPLING NUT (5). Fig. 8.
Important: Do not use lubricants (other than water)
or any type of thread sealing paste or tape.
INSTALL FLUSH VALVE; Fig. 8
5
1. Align the FLUSH VALVE (2) (Fig. 9) directly above
the VACUUM BREAKER TUBE (7) and VACUUM
COUPLING NUT (6). Make sure that GASKET (10) is
installed.
Note: There is a +13mm, -6mm (+1/2, -1/4) tolerance
for the 121mm (4-3/4) dimension. Fig. 9.
2. Pull the VACUUM BREAKER TUBE (7) up to meet
the threaded FLUSH VALVE CONNECTION (8) and
hand tighten the COUPLING NUT (6). Align all
components of the flush valve assembly. Fig. 9.
3. Lightly tighten the TAILPIECE COUPLING NUT (5)
connection first, then the VACUUM BREAKER
COUPLING NUT (6) and finally the SPUD COUPLING
NUT (9). Once alligned correctly, use a wrench to
tighten all couplings to make water tight connections.
Fig. 9.
4. Secure piping behind wall as required.
CONNECT FLUSH VALVE TO
PIPING; Fig. 9
6
3
25
1
4
121mm,+13mm, -6mm
(4-3/4)(+1/2, -1/4)
M968550 REV. 1.5

11
6
1. Remove the four COVER SCREWS (1) and COVER
from (2) ELECTRICAL BOX (4). Fig. 10.
2. Pull the CIRCUIT BOARD (3) out from ELECTRICAL
BOX (4). Fig. 10.
3. Knock out lower blank in ELECTRICAL BOX (4) with
flat blade screwdriver. Install from the back of
ELECTRICAL BOX (4) the POWER SUPPLY GROMMET
(8). Fig. 10a.
4. Attach the SAFETY CHAIN (5) from the FRONT
PANEL (6) to the MOUNTING POST (7) as shown.
Feed the Red and Black wires through the back opening
in the ELECTRICAL BOX (4). Fig. 10a.
5. From back of ELECTRICAL BOX (4) remove SPLIT
PLUG (8a) from POWER SUPPLY GROMMET (8). Insert
POWER CORD CONNECTOR (9) through POWER
SUPPLY GROMMET (8). Insert POWER CORD (10) into
SPLIT PLUG (8a). Push SPLIT PLUG (8a) into POWER
SUPPLY GROMMET (8) to seal. Fig. 10b.
6. Insert POWER SUPPLY CONNECTOR (9) into
RECEPTOR (11) on CIRCUIT BOARD (3).Install
CIRCUIT BOARD (3) into ELECTRICAL BOX (4).
Fig. 10b.
7. Install the SENSOR WIRE GROMMET (15) into the
COVER (2) as shown. Remove the SPLIT PLUG (15a)
from SENSOR WIRE GROMMET (15). Insert SENSOR
WIRE CONNECTOR (12) through SENSOR WIRE
GROMMET (15). Insert SENSOR WIRE (13) into SPLIT
PLUG (15a). Push SPLIT PLUG (15a) into SENSOR
WIRE GROMMET (15) to seal. Fig. 10c.
8. Insert SENSOR WIRE CONNECTOR (12) into
CIRCUIT BOARD RECEPTOR (14) slot. Fig. 10c.
9. Replace COVER (2). Tighten COVER SCREWS (1)
firmly.
CONNECT FRONT PANEL TO
ELECTRICAL BOX (AC POWER);
Fig. 10
7
Fig. 10
Fig. 10a
Fig. 10b
Fig. 10c
TOP
TOP
1
2
3
4
4
4
65
7
3
8
9
11
9
8
15
2
15a
1
12
13
8a
10
KNOCK OUT
BLANK
BLACK &
RED WIRES
14
TOP
8
TOP
7
M968550 REV. 1.5

TOP
1. Remove the four COVER SCREWS (1) and COVER
(2) from ELECTRICAL BOX (3). Fig. 10.
2. Install BATTERY (4) into holder on DC circuit board.
Press BATTERY (4) down (contacts facing downward) into
position until tabs lock BATTERY (4) into place.
3. Attach the SAFETY CHAIN (5) from the FRONT
PANEL (6) to the MOUNTING POST (7) as shown.
Feed the Red and Black wires through the back opening
in the ELECTRICAL BOX (3). Fig. 11a.
4. Install the SENSOR WIRE GROMMET (11) into the
COVER (2) as shown. Remove the SPLIT PLUG (11a)
from SENSOR WIRE GROMMET (11). Insert SENSOR
WIRE CONNECTOR (8) through SENSOR WIRE
GROMMET (11). Insert SENSOR WIRE (9) into SPLIT
PLUG (11a). Push SPLIT PLUG (11a) into SENSOR
WIRE GROMMET (11) to seal. Fig. 11b.
8. Insert SENSOR WIRE CONNECTOR (8) into
CIRCUIT BOARD RECEPTOR (10) slot. Fig. 11b.
9. Replace COVER (2). Tighten COVER SCREWS (1)
firmly.
7
Fig. 11a
Fig. 11b
Fig. 12
1
2
3
4
6
11
2
11a
8
9
1
CONNECT FRONT PANEL TO
ELECTRICAL BOX (DC POWER
BATTERY); Fig. 11
8
Fig. 11
1. Install the two TABS (1) on the back side of FRONT
PANEL (2) into the two SLOTS (3) located on the top
edge of the ELECTRICAL BOX (4). Fig. 12.
2. Push on the bottom edge of the FRONT PANEL (2)
until it snaps into place. If FRONT PANEL (2) will not
snap into place, then loosen the MOUNTING SCREWS
(6) on the ELECTRICAL BOX (4) slightly. Fig. 12.
3. To remove FRONT PANEL (2) insert WIRE KEY (5)
(supplied) into the two holes located at the bottom of the
FRONT PANEL (2). Push the WIRE KEY (5) up until it
releases the bottom clips. Pull the bottom edge away and
lift the FRONT PANEL (2) off. Fig. 12.
INSTALL FRONT PANEL; Fig. 12
9
PUSH TO
SNAP PANEL
INTO PLACE 5
2
TOP
5
7
BLACK &
RED WIRES
TOP
1
2
3
4
6
TOP
3
10
M968550 REV. 1.5

8
1
4
2
5
5
6
BLUE
HOSE
BLACK
HOSE
1. Push the BLACK HOSE (1) into the BOTTOM HOSE
CONNECTOR (2) and the other end into the back of the
OVERRIDE SWITCH (3).
2. Push the BLUE HOSE (4) into the TOP HOSE
CONNECTOR (5) on the valve and the other end into the
BOTTOM CONNECTOR (6) on the OVERRIDE SWITCH
(3).
CONNECT OVERRIDE HOSES,
AC & DC POWER; Fig. 13
10
1. Push the RED WIRE CONNECTOR (1) onto the
SOLENOID PIN (2) with Red Stripe. Push the BLACK
WIRE CONNECTOR (3) onto the other SOLENOID PIN
(4). Push the wire connectors all the way down.
2. Code approved Electrical Outlet provided by others,
(120V 50/60 Hz).
3. Plug AC POWER SUPPLY (5) into Outlet.
CONNECT SOLENOID WIRING
AND POWER SUPPLY; Fig. 14
11
Fig. 13
Fig. 14
3
RED
WIRE
RED
STRIPE
BLACK
WIRE
ELECTRICAL
OUTLET
13
24
M968550 REV. 1.5

FOR AC-VERSION
(MULTI HOOK-UP); Fig. 15, 15a
Unit #1
Unit #1
Unit #2 Unit #3
1.Remove the COVER SCREWS (1) and COVER (2) from
each ELECTRICAL BOX (3).
2. See AC Version Electrical Hook-up for Unit #1 of the Multi
hook-up.
3. Install SENSOR WIRE GROMMET (4) and FLUSH VALVE
SENSOR WIRE (5) into the COVER (2) of each unit. Insert
the flush valve sensor wire connector into the CENTER
CIRCUIT BOARD RECEPTOR (6) on each unit. Fig. 15a.
4. Remove the SPLIT PLUG (7a) from the SENSOR WIRE
GROMMET (7) on the left side of each ELECTRICAL BOX (3).
5. Take the 10 ft. EXTENSION WIRE (8) from Unit #2 and
insert one end of the EXTENSION WIRE CONNECTOR (9)
through the SENSOR WIRE GROMMET (7) on left side of Unit
#1. Insert EXTENSION WIRE (8) into SPLIT PLUG (7a). Push
SPLIT PLUG (7a) into SENSOR WIRE GROMMET (7) to seal.
Insert EXTENSION WIRE CONNECTOR (9) into LOWER
CIRCUIT BOARD RECEPTOR (10). Fig. 15a.
6. Insert other end of EXTENSION WIRE (8) into SENSOR
WIRE GROMMET (7) on left side of Unit #2. Insert that
EXTENSION WIRE CONNECTOR (9) into the LOWER
CIRCUIT BOARD RECEPTOR (10) of Unit #2. Fig. 15b.
7. On Unit #2 ELECTRICAL BOX (3) remove ROUND
KNOCK-OUT (11) on the bottom of the box by pressing a
flathead screwdriver into the center of the ROUND
KNOCK-OUT (11). Fig 15b.
8. Insert additional SENSOR WIRE GROMMET (12) included
with Unit #2 into the knock-out opening in the bottom of the
ELECTRICAL BOX (3). Take the 10 FT. EXTENSION WIRE
(8) from Unit #3 and insert one end into the SENSOR WIRE
GROMMET (12) in the bottom of the ELECTRICAL BOX (3) of
Unit #2. Insert EXTENSION WIRE CONNECTOR (9a) into
TOP CIRCUIT BOARD RECEPTOR (13) on Unit #2 . Fig.
15b.
9. Insert the other end of the EXTENSION WIRE (8) from Unit #3
into the SENSOR WIRE GROMMET (7) on the left side of Unit
#3. Insert EXTENSION WIRE CONNECTOR (9) into LOWER
CIRCUIT BOARD RECEPTOR (10) on Unit #3.
10. Repeat Steps 7 to 9 as necessary for additional Multi-AC
Units.
11. Once all wire connections are made. Install the COVER (2)
and COVER SCREWS (1) onto each ELECTRICAL BOX (3).
Fig. 15
Fig. 15a
Fig. 15b
12
9
TOP TOP TOP
27a
7
8
3
6
1
54
9
TOP
10
SENSOR WIRE
CONNECTOR
SENSOR
WIRE
FROM UNIT #2
Unit #2
7a
7
8
3
9a
TOP
12
7
12
8
88 8
12
11
10
9
SENSOR WIRE
CONNECTOR
FROM
UNIT #3
BACK OF BOX (3)
FROM UNIT #1
REMOVE KNOCK-OUT (11),
INSERT WIRE GROMMET (12)
1
2
SENSOR
WIRE
SENSOR
WIRE
6
10
7
6
10
13
7
6
10
13
13
M968550 REV. 1.5