American Standard PORTSMOUTH 4285.100 User manual

1INSTALL FAUCET WITH OR WITHOUT DECK ESCUTCHEON
PUTTY
SINK OR
MOUNTING
SURFACE
SPOUT BASE
Assemble RUBBER WASHER (4), BRASS WASHER (5), and threaded LOCKNUT (6) onto SHANK (3) from underside
of sink or mounting surface. Hand tighten LOCKNUT (6).
Use a screwdriver to tighten SCREWS (8) on LOCKNUT (6). Work your way around LOCKNUT (6), tightening
the screws slightly each time until all are snug to ensure even pressure.
(A) Installation with ESCUTCHEON (1).Apply a bead of putty to bottom edge of ESCUTCHEON with PUTTY PLATE (1).
Insert SUPPLY HOSES (2), SPRAY HOSE (7) and SHANK (3) through hole of ESCUTCHEON with PUTTY PLATE (1) and
mounting surface. Follow mounting instructions below to secure faucet to mounting surface.
(B) Installation less ESCUTCHEON (1).Insert all HOSES (2) and SHANK (3) through MOUNTING RING (10) and
mounting surface. Do not use putty.
Plumbers' Putty or CaulkingAdjustable WrenchPhillips Screwdriver
RECOMMENDED TOOLS
Regular Screwdriver
Insert HOSES (2) through RUBBER WASHER (4), BRASS WASHER (5), and threaded LOCKNUT (6).
Turn off water at
main supply.
CAUTION
Make certain the SEAL (9) is properly seated in recess of spout base.
M965456 Rev. 1.2
SINGLE CONTROL
KITCHEN PULL-OUT FAUCET
Installation
Instructions
Certified to comply with ANSI A112.18.1M
4285.100
4285.100F15
PORTSMOUTH™
Thank you for selecting American-Standard...
the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--
please read these instructions carefully before you begin.
1
99
3
B
A
10
2
3
2
4
5
8
6
7
4
5
8
6
7

2MAKE WATER SUPPLY CONNECTIONS
3CONNECT SPRAY HOSE AND INSTALL WEIGHTS
With PULL-OUT SPRAY (1) seated in FAUCET (2),
install WEIGHTS (3) onto HOSE (4) using two
SCREWS (5). Locate the WEIGHTS (3) two feet (2')
from the underside of the sink deck.
Tighten SCREWS (5) firmly.
Make sure SEAL WASHER (7) is installed in COUPLING
NUT (6). Connect threaded end of HOSE (4) to SPRAY HOSE
COUPLING NUT (6) from fitting. Use wrench to tighten.
1
2
COLD
HOT
Turn off hot and cold water supplies before beginning.
Connect FLEXIBLE SUPPLIES (1, 2) directly
to wall supplies. Connection on fitting
supplies are 3/8" compression. Connect
left supply (Marked with a Red Stripe) to Hot
and right supply (Marked with Blue Stripe) to
Cold wall supply. Use adjustable wrench to
tighten connections. Do not over tighten.
Faucet supplies are 24" long from faucet base.
Note: If additional supply length is
required, installer must purchase
additional parts separately.
Important: If SUPPLY HOSES (1, 2) are
too long, loop as illustrated to avoid kinking.
2
CHECK CONNECTIONS FOR LEAKS.
Move HANDLE (1) down into "off" position.
Turn on water supplies and check connections
for leaks.
CHECK CONNECTIONS
FOR LEAKS
4
1
M965456 Rev. 1.2
1
4
6
7
24"
(610mm)
53

5TEST INSTALLED FAUCET
SPRAY OPERATION
With FAUCET on, press TOGGLE BUTTON (6) on
SPRAY (3) to switch from stream to spray.
STREAM (AERATOR)
SPRAY
36
4
Move HANDLE (1) down into "off" position.
With HANDLE (1) down in "off" position, pull HAND SPRAY (2) from SPOUT (3). SPRAY (HOSE (4) should pull
approximately 2 feet and direct open SPRAY END (5) into sink.
Operate handle up and down, in COLD and HOT positions,
to flush water lines thoroughly.
Check HAND SPRAY (2) operation:
6
M965456 Rev. 1.2
1
5
3
2
ADJUST HOT LIMIT STOP
By restricting handle rotation and limiting the amount of hot water allowed to mix with the cold, the HOT LIMIT SAFETY STOP
reduces risk of accidental scalding. To set the maximum hot water temperature of your faucets, all you need to do is adjust
the setting on the HOT LIMIT SAFETY STOP.
Use a flat blade screwdriver or your fingers to pull up and rotate red HOT LIMIT SAFETY STOP (1). Follow Step "A" or "B" to
adjust min./max. discharge temperature. "1" being the hottest to "8" the coldest temperature setting. Factory set at "1".
HOT LIMIT SAFETY STOP ADJUSTMENT
PRY RED RING UPWARD
AND ROTATE
COUNTER-CLOCKWISE
"A"
ADJUSTMENT WHEN WATER IS TOO HOT
PRY RED RING UPWARD
AND ROTATE CLOCKWISE
"B"
ADJUSTMENT WHEN
WATER IS TOO COLD
"RED RING"- HOT LIMIT SAFETY STOP
"B"
"A" TEMPERATURE
SETTING NUMBERS

8CARE:
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
SERVICE
7
Clogged CARTRIDGE outlets or inlets may cause reduced flow.
To clean, first turn off water supply then:
1
2
3
4
If Faucet Drips Proceed As Follows:
Turn VALVE in OFF position.
If faucet drips, operate HANDLE several times from OFF to ON position.
Do not apply excessive force.
FLOW CONTROL DEVICE may accumulate dirt. To remove the FLOW
CONTROL DEVICE, unthread SPRAY AND HOSE ASSEMBLY and
rinse clean FLOW CONTROL DEVICE.
Remove INDEX BUTTON (1), loosen HANDLE SCREW (2) and remove HANDLE (3).
Unthread ESCUTCHEON CAP (4). Unthread three MOUNTING SCREWS (5).
Lift CARTRIDGE (6) off MANIFOLD (7) and remove CARTRIDGE SEALS (8).
Place SEALS (8) into CARTRIDGE PORTS (6a).
Replace ESCUTCHEON CAP (4), HANDLE (3), tighten HANDLE
SCREW (1) and install INDEX BUTTON (2).
Test fitting.
Clean MANIFOLD (7), CARTRIDGE (6) ports and SEALS (8).
Place CARTRIDGE (6) onto MANIFOLD (7) and tighten MOUNTING
SCREWS (5) alternately.
5
6
8
7
6a
M965456 Rev. 1.2
Flow Control
Device
Spray and Hose
Assembly

SINGLE CONTROL KITCHEN
PULL-OUT FAUCET
PORTSMOUTH™
MODEL NUMBERS
A911897-0070A
SEAL
M964065-YYY0A
ESCUTCHEON AND
PUTTY PLATE
M962146-0070A
MOUNTING KIT
CHROME
STAINLESS STEEL
OIL RUBBED BRONZE
002
075
224
Replace the YYY with
Appropriate finish code
M918506-0070A
CARTRIDGE SCREWS
M964398-YYY0A
HANDLE KIT
M951471-0070A
CARTRIDGE
M907302-YYY0A
ESCUTCHEON CAP
M962994-0070A
BUTTON AND
SCREW KIT
M965456 Rev. 1.2
For toll-free information and answers to your questions, call:
1-800-442-1902
Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-1200
Product names listed herein are trademarks of American Standard Inc.
© AS America, Inc. 2013
HOT LINE FOR HELP
M907989-YYYOA
MOUNTING RING KIT
M953666-YYY220A
(2.2 GPM)
SPRAY WITH HOSE
M953666-YYY150A
(1.5 GPM)
SPRAY WITH HOSE
M964395-0070A
WEIGHT
4285.100
4285.100F15