American Standard Townsquare 2555.801 User manual

Plumbers' Putty or Caulking
Adjustable Wrench Phillips Screwdriver
Channel Locks
TOOLS REQUIRED
SPREAD LAVATORY FAUCETS
Installation
Instructions
.3&7
Certified to comply with ANSI A112.18.1M
SPOUT ASSEMBLY
VALVE INSTALLATION

Insert VALVE BODY (1) through hole from underside
of SINK (2). Threads of VALVE BODY (1) should extend
at least 5/16 inch above SINK (2) top. If necessary,
adjust LOCKNUT (3). Make sure RUBBER WASHER (6)
is installed.
Place RUBBER RING (4) into DECK ADAPTER (5) and
screw DECK ADAPTER (5) onto VALVE BODY (1) until
snug against internal stop.
Set VALVE BODIES (1,1A) so that their outlets are
facing toward center of sink and then tighten LOCKNUT
(3) using WRENCH (7) supplied with faucet.
TOWNSQUARE 2555.801
Insert SPOUT SHANK (1) through center hole of SINK (2).
Make sure RING WASHER (3) is properly positioned into
SPOUT BASE.
Assemble RUBBER WASHER (4), BRASS WASHER (5)
and LOCKNUT (6) onto threads of SPOUT SHANK (1)
from underside of SINK (2).
Insert LIFT ROD (7) through SPOUT (8)
and slot of BRASS WASHER (5).
Align SPOUT (8) and tighten LOCKNUT (6).
Be sure slot in BRASS WASHER (5) is
positioned to the rear as shown.
Turn off hot and cold water
supplies before beginning.
CAUTION
4
2
6
1
3
5/16'' MIN.
7
5
7
8
1
3
SLOT
24
6
5
Congratulations on purchasing your American Standard faucet
with EverClean nish found only on American Standard faucets.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
with EverClean™ Finish
EverClean Finish
• One wipe eortlessly removes spots
• Eliminates the need for cleaners and scrubbing
• Permanent surface protectant remains beautiful
for the life of the faucet
• EverClean™ available on: Polished Chrome, Satin Nickel,
Stainless Steel, Polished Brass (or any combination of these nishes)

.3&7
TEE AND HOSE INSTALLATION 
3
MAKE WATER SUPPLY CONNECTIONS
Connect water supply to FAUCET (1) with 1/2" IPS
FLEXIBLE SUPPLIES (3) or 3/8" O.D.
BULL-NOSE RISERS (4). Use
adjustable wrench to tighten
connections.
Do not over tighten.
Be careful not to kink
copper supply when
bending. Use tubing
cutter to cut to
proper length.
14
FERRULE
NOTE: FLEXIBLE SUPPLIES OR BULL-NOSE RISERS MUST BE
PURCHASED SEPARATELY.
COUPLING
NUT
Connect TEE (1) to SPOUT SHANK (2). Tighten COUPLING
NUT (3).
Connect COUPLING NUTS (4) of HOSE to each valve outlet and
tighten securely.
1
3
2
4
VALVE
OUTLET
HOSE
INSTALL HANDLES
1
2
3
4
5
6
7
10
Figure B
Figure A
Figure D
Figure C
4
5
6
10
5
10
8
Turn VALVE to OFF position.
Figure A: Install STEM ADAPTERS (7) onto VALVE STEMS (8).
Figure B: With colored side up, place FRICTION RING (6) over DECK ADAPTER (10). Loosely screw FRICTION NUT (5)
onto DECK ADAPTER (10). Do not tighten. Align flats on FRICTION NUT (5) with RIBS (9) in HANDLE BASE (4).
Figure C: Screw HANDLE BASE (4) with FRICTION NUT (5) onto DECK ADAPTER (10) until snug against mounting
surface and aligned properly.
Figure D: Install LEVER HANDLE (3) onto HANDLE ADAPTER (7) and align. Check alignment, if not satisfactory remove
and align. Insert HANDLE SCREW (2) and tighten. Press in INDEX BUTTON (1).
9
4
FLATS
ALIGNED

.3&7
INSTALL POP-UP DRAIN

1
2
A
3
4
5
10
11
12
8
G
D
E
6
7
F
C
9
Push Tail piece (11) down into Trap (C) (threaded end up).
Assemble Pivot Rod (9) as shown in Figure-4B. Notice the
position of the Concave Washer (G).
Insert Pivot Rod (9) into Drain Body (10) and tighten Pivot
Nut (F).
Thread Locknut (5), Washer (4) and Gasket (3) (Bevel side
up) onto Drain Body (10).
Apply a bead of Putty (D) to underside of Flange (2).
Remove one end of Clip (8) from Pivot Rod (9) by squeezing
ends together while sliding.
Insert Pivot Rod (9) into second or third hole in Extension
Rod (7) and reassemble Clip (8).
Adjust stopper height by repositioning Extension Rod (7) and
tightening Thumbscrew (6).
Feed Drain Body (10) up through Sink (A) and thread the
Flange (2) fully onto Drain Body (10).
Tighten Locknut (5) firmly, keeping the pivot rod hole pointed
towards the back of the sink.
Drop Stopper (1) into Drain Body (10).
Position Extension Rod (7) onto Pop-Up Rod (E) and tighten
Thumbscrew (6).

'*(63&#
Push TAILPIECE INSERT (12) into TAILPIECE (11) and push
TAILPIECE up and thread tightly into DRAIN BODY (10).
F
TEST INSTALLED FITTING
With HANDLES (1) in OFF position, turn on WATER SUPPLIES (2)
and check all connections for leaks.
Remove AERATOR (3).
Operate both HANDLES to flush water lines thoroughly.
Replace AERATOR (3).
1
2
3
03*/(

.3&7
SERVICE
CHECK DRAIN CONNECTIONS
1
2
3
Operate Lift Rod and fill lavatory with water. Check that
DRAIN STOPPER (1) makes a good seal and retains water
in lavatory. Adjust stopper height by repositioning Lift
Rod (2) and tightening Thumbscrew (3).
Release DRAIN STOPPER (1) and check all drain
connections and "P" trap for leaks. Tighten if necessary.
To change direction of handle rotation,
proceed as follows:
Turn valve to OFF position.
Pull out INDEX CAP (1) and remove
HANDLE SCREW (2).
Pull off HANDLE (3) and unscrew
ESCUTCHEON BASE (4).
Remove SPRING CLIP (6).
Lift STOP WASHER (5), turn 90pand replace.
Replace SPRING CLIP (6).
Reinstall ESCUTCHEON (4) and HANDLE
ASSEMBLY.
If spout drips, operate handles several times
from OFF to ON position. Do not force - handles
turn only 90p.
90p
5
6
4
3
2
1
American Standard’s EverClean finish will wipe clean with a soft, dry cloth. A soft cloth with clean
water may also be used, if desired. No additional cleaning products are required.
DO NOT USE: Soaps, acid, polish, abrasives, harsh cleaners, or a cloth with a coarse surface.
EverClean™ Finish Care Instructions


.3&7
A911903-0070A
SEAL
SPREAD LAVATORY
FAUCETS
024220-0070A
SUPPLY NUT
072574-0070A
EXTENSION ROD
M961732-YYY0A
LIFT ROD 2555.801
066116-YYY0A
DRAIN STOPPER
GASKET
WASHER
LOCKNUT
M961711-0070A
TAILPIECE INSERT
900864-0070A
DRAIN BODY
FLANGE
070847-0070A
CLIP
066118-0070A
PIVOT ROD
953450-YYY0A
COMPLETE
DRAIN ASSEMBLY
070532-0040A
TAILPIECE
066117-YYY0A
FLANGE KIT
TOWNSQUARE
M953006-0070A
TEE & HOSE KIT
CHROME 002
POLISHED BRASS 099
SATIN NICKEL 295
Replace the "YYY" with
appropriate finish code
A922869-YYY0A
AERATOR
M961729-0070A
FRICTION NUT
AND RING
M916807-YYY0A
LEVER HANDLE
M962104-YYY0A
HANDLE BASE KIT
994053-0070A
CARTRIDGE
M961634-0070A
VALVE MOUNTING KIT
M918305-0070A
HANDLE SCREW
M918025-0070A
HANDLE ADAPTER
M961730-0070A
DECK ADAPTER KIT
M961731-YYY0A
SPOUT KIT
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 [phone]
Weekdays 8:00 a.m. to 8:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
Product names listed herein are trademarks of American Standard Inc.
© American Standard Inc. 2002
M907024-YYY0A
INDEX BUTTON
(HOT & COLD)
M961733-0070A
SPOUT
MOUNTING KIT
IN MEXICO 01-800-839-12-00