Ameriphone SR100 User manual

©AMERIPHONE products are manufactured by Walker,
A Division of Plantronics, Inc.
12082 Western Avenue, Garden Grove, CA 92841
[phone] VOICE • [phone] TTY/TDD
[phone] FAX
email: [email protected]
website: www.ameriphone.com
®

E
N
G
L
I
S
H
SR200 M52002 A4/03
SUPER PHONE RINGER
MODEL SR-100
®
Users’ Guide
∆

Operation . . . . . . . . . . . . . .3
Safety Information . . . . . . . . .4
Installation . . . . . . . . . . . . .11
Warranty . . . . . . . . . . . . . .14
Your Satisfaction . . . . . . . . .15
Regulatory Compliance . . . .16
Table Of Contents

Operation
1. Select the ring pattern.
2. Adjust ringing tone.
3. Adjust the volume.
(When it is turned to OFF,
light will still flash when
phone rings.)
E
N
G
L
I
S
H
xxx3

Important Safety Instructions
When using your SR-100 Super Phone Ringer,
basic safety precautions should always be
followed to reduce the risk of fire, electric shock
and persons including the following:
1. Read and understand all instructions.
2. Follow all warnings and instruction
marked on the SR-100 Super Phone Ringer.
3. Do not use this SR-100 Super Phone
Ringer near a bathtub, wash basin,
kitchen sink or laundry tub, in a wet
basement, near a swimming pool or
anywhere else there is water.
4. Avoid using a telephone (other than a
cordless type) during a storm. There
may be a remote risk of electrical
shock from lightning.
5. Do not use the telephone to report a
gas leak in the vicinity of the leak.
6. Unplug the SR-100 Super Phone Ringer
from the wall outlets before cleaning. Do
4xxx

not use liquid cleaners or aerosol
cleaners on the product. Use a damp
cloth for cleaning.
7. Place this ringer on a stable surface.
Serious damage and/or injury may
result if the telephone falls.
8. Do not cover the slots and openings
on this product. It should never be
placed near or over a radiator or heat
register. It should not be placed in a
built-in installation unless proper
ventilation is provided.
9. Operate this product using the
electrical voltage as stated on the base
unit or the owner’s manual. If you are
not sure of the voltage in your home,
consult your dealer or local power
company.
10. Do not place anything on the power
cord. Install the product where no
one will step or trip on the cord.
11. Do not overload wall outlets or extension
cords as this can increase the risk of fire
E
N
G
L
I
S
H
xxx5

or electrical shock.
12. Never push any objects through the
slots in the product. They can touch
dangerous voltage points or short out
parts that could result in a risk of fire
or electrical shock. Never spill liquid of
any kind on the product.
13. To reduce the risk of electrical shock, do
not take this product apart. Opening or
removing covers may expose you to
dangerous voltages or other risks.
Incorrect reassembly can cause electric
shock when the product is subsequently
used.
14. Unplug this product from the wall outlets
and refer servicing to the manufacturer
under the following conditions:
A.When the power supply cord or plug
is frayed or damaged.
B. If liquid has been spilled into the
product.
C.If the product has been exposed to
6xxx

rain or water.
D.If the product does not operate
normally by following the operating
instructions. Adjust only those controls
that are covered by the operating
instructions. Improper adjustment may
require extensive work by a qualified
technician to restore the product to
normal operation.
E. If the ringer has been dropped or
the case has been damaged.
F. If the product exhibits a distinct
change in performance.
15. Never install telephone wiring during
a lightning storm.
16. Never install telephone jacks in wet
locations unless the jack is specifically
designed for wet locations.
17. Never touch uninsulated telephone
wires or terminals unless the telephone
line has been disconnected at the
network interface.
E
N
G
L
I
S
H
xxx7

18. Use caution when installing or
modifying telephone lines.
19. Use only the power cord and batteries
indicated in this manual. Do not
dispose of batteries in a fire. They
may explode. Check with local codes
for possible special disposal instructions.
ADDITIONAL SAFETY NOTES FOR
CANADIAN USERS
The following items are included as part of the
CS-03 Requirements. The standard connecting
arrangement for the equipment is CA11A. This
product meets the applicable Industry Canada
technical specifications.
NOTICE: The Canadian Department of
Communications label identifies certified
equipment. This certification means that the
equipment meets certain telecommunications
network protective operational and safety
8xxx

requirements. The Department does not
guarantee that the equipment will operate to
the user’s satisfaction. Before installing this
equipment, users should ensure that it is
permissible to be connected to the facilities of
the local telecommunications company. The
equipment must also be installed using an
acceptable method of connection. In some
cases, the company’s inside wiring associated
with a single line individual service may be
extended by means of a certified connector
assembly (telephone extension cord). The
customer should be aware that compliance with
the above conditions may not prevent
degradation of service in some situations.
Repairs to certified equipment should be made
by an authorized Canadian maintenance
facility designated by the supplier. Any repairs
or alterations made by the user to this
equipment, or equipment malfunctions, may
give the telecommunications company cause to
request the user disconnect the equipment.
E
N
G
L
I
S
H
xxx9