Ameriphone SR200 User manual

©AMERIPHONE products are manufactured by Walker,
A Division of Plantronics, Inc.
12082 Western Avenue, Garden Grove, CA 92841
[phone] VOICE • [phone] TTY/TDD
[phone] FAX
email: [email protected]
website: www.ameriphone.com
®

E
N
G
L
I
S
H
E
S
P
A
Ñ
O
L
F
R
A
N
Ç
A
I
S
SR200 M52002 A4/03
SUPER PHONE RINGER
MODEL SR-200 & SR-95
®
Users’Guide
∆

Operation . . . . . . . . . . . . . .3
Safety Information . . . . . . . . .4
Installation . . . . . . . . . . . . .15
Warranty . . . . . . . . . . . . . .18
Your Satisfaction . . . . . . . . .19
Regulatory Compliance . . . .20
Table Of Contents

Operation
1. Select the ring pattern.
2. Adjust ringing tone.
3. Adjust the volume.
(When it is turned to OFF,
light will still flash when
phone rings.)
E
N
G
L
I
S
H
xxx3

Important Safety Instructions
When using your SR-200 Super Phone Ringer,
basic safety precautions should always be
followed to reduce the risk of fire, electric shock
and persons including the following:
1. Read and understand all instructions.
2. Follow all warnings and instruction
marked on the SR-200 Super Phone Ringer.
3. Do not use this SR-200 Super Phone
Ringer near a bathtub, wash basin,
kitchen sink or laundry tub, in a wet
basement, near a swimming pool or
anywhere else there is water.
4. Avoid using a telephone (other than a
cordless type) during a storm. There
may be a remote risk of electrical
shock from lightning.
5. Do not use the telephone to report a
gas leak in the vicinity of the leak.
6. Unplug the SR-200 Super Phone Ringer
from the wall outlets before cleaning. Do
4xxx

not use liquid cleaners or aerosol
cleaners on the product. Use a damp
cloth for cleaning.
7. Place this ringer on a stable surface.
Serious damage and/or injury may
result if the telephone falls.
8. Do not cover the slots and openings
on this product. It should never be
placed near or over a radiator or heat
register. It should not be placed in a
built-in installation unless proper
ventilation is provided.
9. Operate this product using the
electrical voltage as stated on the base
unit or the owner’s manual. If you are
not sure of the voltage in your home,
consult your dealer or local power
company.
10. Do not place anything on the power
cord. Install the product where no
one will step or trip on the cord.
11. Do not overload wall outlets or extension
cords as this can increase the risk of fire
E
N
G
L
I
S
H
xxx5

or electrical shock.
12. Never push any objects through the
slots in the product. They can touch
dangerous voltage points or short out
parts that could result in a risk of fire
or electrical shock. Never spill liquid of
any kind on the product.
13. To reduce the risk of electrical shock, do
not take this product apart. Opening or
removing covers may expose you to
dangerous voltages or other risks.
Incorrect reassembly can cause electric
shock when the product is subsequently
used.
14. Unplug this product from the wall outlets
and refer servicing to the manufacturer
under the following conditions:
A.When the power supply cord or plug
is frayed or damaged.
B. If liquid has been spilled into the
product.
C.If the product has been exposed to
6xxx

rain or water.
D.If the product does not operate
normally by following the operating
instructions. Adjust only those controls
that are covered by the operating
instructions. Improper adjustment may
require extensive work by a qualified
technician to restore the product to
normal operation.
E. If the ringer has been dropped or
the case has been damaged.
F. If the product exhibits a distinct
change in performance.
15. Never install telephone wiring during
a lightning storm.
16. Never install telephone jacks in wet
locations unless the jack is specifically
designed for wet locations.
17. Never touch uninsulated telephone
wires or terminals unless the telephone
line has been disconnected at the
network interface.
E
N
G
L
I
S
H
xxx7

18. Use caution when installing or
modifying telephone lines.
19. Use only the power cord and batteries
indicated in this manual. Do not
dispose of batteries in a fire. They
may explode. Check with local codes
for possible special disposal instructions.
ADDITIONAL SAFETY NOTES FOR
CANADIAN USERS
The following items are included as part of the
CS-03 Requirements. The standard connecting
arrangement for the equipment is CA11A. This
product meets the applicable Industry Canada
technical specifications.
NOTICE: The Canadian Department of
Communications label identifies certified
equipment. This certification means that the
equipment meets certain telecommunications
network protective operational and safety
8xxx

requirements. The Department does not
guarantee that the equipment will operate to
the user’s satisfaction. Before installing this
equipment, users should ensure that it is
permissible to be connected to the facilities of
the local telecommunications company. The
equipment must also be installed using an
acceptable method of connection. In some
cases, the company’s inside wiring associated
with a single line individual service may be
extended by means of a certified connector
assembly (telephone extension cord). The
customer should be aware that compliance with
the above conditions may not prevent
degradation of service in some situations.
Repairs to certified equipment should be made
by an authorized Canadian maintenance
facility designated by the supplier. Any repairs
or alterations made by the user to this
equipment, or equipment malfunctions, may
give the telecommunications company cause to
request the user disconnect the equipment.
E
N
G
L
I
S
H
xxx9

Users should ensure for their own protection
that the electrical ground connections of the
power utility, telephone lines and internal
metallic water pipe system, if present, are
connected together. This precaution may be
particularly important in rural areas.
CAUTION: Users should not attempt to make
such connections themselves, but should contact
the appropriate electric inspection authority, or
electrician, as appropriate. The Ringer Equivalent
Number is an indication of the maximum
number of terminals allowed to be connected to
a telephone interface. The termination on an
interface may consist of any combination of
devices subject only to the requirement that the
sum of the Ringer Equivalent Number of all the
devices not exceed five.
SAVE THESE INSTRUCTIONS
10xxx

E
N
G
L
I
S
H
Installation
xxx11
43
12
Battery Installation (If AC adapter
is used, use rechargeable NICad
batteries* as optional power
back-up)
Phone cord retainer
*Do not burn or puncture the batteries.
Like other batteries of this type, if they are
burned or punctured, they could release
toxic material which could cause injury.
Do not dispose of them in household
garbage. For information about recycling
or proper disposal, consult your local solid
waste (garbage) collection or disposal
organization.
Ni-Cd

123
456
789
0#
*
AC adapter (9 VDC,
300 mA, if provided.
If AC adapter is used,
use rechargeable NiCad
batteries as optional
power back-up).
Phone
Phone
outlet
to SR-200
to phone
for U.K. only
12xxx
Installation

E
N
G
L
I
S
H
Connecting the
Phone Ringer:
For wall mounting, use two
screws, three inches apart,
or use double-sided tape.
xxx13
Ringing tone adjustment
Ring pattern selection
Volume control

Warranty
Ameriphone will repair or
replace your Super Phone
Ringer for one year from the
date of purchase if the unit is
defective in workmanship or
materials. Proof of purchase is
required. After the one-year
warranty period, Ameriphone
will repair your unit at a
minimal charge. For further
information on either
in-warranty or out-of-warranty
repairs, contact customer
service @ 800.874.3005
14xxx

Your Satisfaction
Your satisfaction with our
products is very important to
us. We would like to know
what you like or dislike about
this product and what we can
do to make this product even
more beneficial to you. Please
give us your comments by
calling our Customer Service
Department at (800) 874-
3005. We value your
comments and thank you
again.
E
N
G
L
I
S
H
15

Regulatory Compliance
Part 68 of FCC Rules Information
This equipment complies with Part 68 of the
FCC rules and the requirements adopted by
the ACTA. On the bottom of this equipment
is a label that contains, among other
information, a product identifier in the format
US:AAAEQ##TXXXX. If requested, this
number must be provided to the telephone
company.
A plug and jack used to connect this
SR-200 / SR95 Ringer to the premises
wiring and telephone network must comply
with the applicable FCC Part 68 rules and
requirements adopted by the ACTA. A
compliant telephone cord and modular plug,
RJ11 USOC, is provided with this product. It
is designed to be connected to a compatible
modular jack that is also compliant. See
16xxx

installation instructions for details.
The REN is used to determine the number of
devices that may be connected to a
telephone line. Excessive RENs on a
telephone line may result in the devices not
ringing in response to an incoming call. In
most but not all areas, the sum of RENs
should not exceed five (5.0). To be certain of
the number of devices that may be connected
to a line, as determined by the total RENs,
contact the local telephone company. For
products approved after July 23, 2001, the
REN for this product is part of the product
identifier that has the format US:AAAEQ##TXXXX.
The digits represented by ## are the REN
without a decimal point (e.g., 03 is a REN
of 0.3). For earlier products, the REN is
separately shown on the label. If this
telephone equipment, the SR200 / SR95
super phone ringer causes harm to the
telephone network, the telephone company
E
N
G
L
I
S
H
xxx17

will notify you in advance that temporary
discontinuance of service may be required.
But if advance notice isn’t practical, the
telephone company will notify the customer
as soon as possible. Also, you will be
advised of your right to file a complaint with
the FCC if you believe it is necessary. The
telephone company may make changes in its
facilities, equipment, operations or procedures
that could affect the operation of the
equipment. If this happens the telephone
company will provide advance notice in
order for you to make necessary modifications
to maintain uninterrupted service.If trouble is
experienced with this telephone equipment,
for repair or warranty information, please
contact Walker / Ameriphone, 1-800-874-
3005. If the equipment is causing harm to
the telephone network, the telephone
company may request that you disconnect
18xxx

the equipment until the problem is resolved.
DO NOT DISASSEMBLE THIS EQUIPMENT.
This telephone equipment is not intended to
be repaired and it contains no repairable
parts. Opening the equipment or any
attempt to perform repairs will void the
warranty. For service or repairs, call 1-800-
874-3005.Connection to party line service is
subject to state tariffs. Contact the state
public utility commission, public service
commission or corporation commission for
information.
If your home has specially wired alarm
equipment connected to the telephone line,
ensure the installation of this telephone
equipment does not disable your alarm
equipment. If you have questions about what
E
N
G
L
I
S
H
xxx19