Ametek AMEVision 3050 Series User manual

AMEVision, Zone 1
For 3050 Moisture Analyzer Series
3050-OLV, 3050-SLR, 3050-DO, 3050-TE
ESSENTIAL HEALTH and SAFETY
PN 305983902_Rev A
9000-182-VE Rev A

To obtain a PDF of this manual, visit our Products page at www.ametekpi.com.
Copyright Notice © 2021 AMETEK Process Instruments. All rights reserved.
The information and descriptions in this document are the sole property of AMETEK Process Instruments and may not be copied, reproduced, disseminated, or
distributed without explicit written permission from AMETEK Process Instruments.
The statements, congurations, technical data, and recommendations in this document are believed to be accurate and reliable at the time of this publication,
but AMETEK Process Instruments assumes no responsibility or liability for any errors or inaccuracies that may appear in this document.
AMETEK Process Instruments is not responsible for any infringement of patents or other rights of third parties that may result from the use of this document. The
content of this document is furnished for informational purposes only, is subject to change without notice, and does not represent a commitment or guaranty by
AMETEK Process Instruments.
AMETEK Process Instruments makes no warranty, express or implied, with respect to the content of this document. AMETEK Process Instruments shall not be
liable for any loss or damage, including consequential or special damages, resulting from any use of this information, even if loss or damage is caused by AMETEK
Process Instruments as a result of negligence or any other fault.

Contents
OVERVIEW....... .........................................................................................................................1
About This Document...............................................................................................................................1
Important Safety Information................................................................................................................2
Warnings, Cautions, Notes...............................................................................................................2
Warning Labels....................................................................................................................................2
Special Conditions for Safe Use.....................................................................................................3
HAZARDOUS LOCATION LIMITATIONS..................................................................................3
Electrical Safety ...................................................................................................................................4
Grounding.............................................................................................................................................4
Environmental Information (WEEE) .....................................................................................................5
SPECIFICATIONS.......................................................................................................................7
AMEVision Display User Interface.........................................................................................................7
APPROVALS AND CERTIFICATIONS ........................................................................................9
System Compliance ...................................................................................................................................9
AMEVision Display User Interface Rating Label...............................................................................9
INSTALLING THE AMEVISION DISPLAY USER INTERFACE ..................................................11
Pre-Installation Requirements ............................................................................................................11
Personnel Technical Level Required for Installation............................................................12
AMEVision Display Site Location................................................................................................ 13
Unpacking and Inspecting the Equipment............................................................................ 13
Mechanical Installation.......................................................................................................................... 14
AMEVision Display User Interface Overview..........................................................................14
AMEVision Software Display and Keypad..........................................................................15
Basic Elements of the AMEVision Display Unit..................................................................15
Accessing the Keypad on the Explosion-Proof Unit .........................................................16
Installing the AMEVision Display Unit......................................................................................17
AC Power and Communication Connections................................................................................ 18
General Wiring and Conduit Requirements...........................................................................18
Interface Connectivity – Setting the Analyzer Address ..................................................... 18
AMEVision D1/Z1 Mains Supply Connections.......................................................................19
EMC Grounding, Shielding, and Noise Protection............................................................19
EMC Grounding Method ........................................................................................................20
Transient and RFI Interference..............................................................................................20
Contents | i
PN 305983902, Rev A

This page intentionally left blank.
ii | AMEVision Zone 1, for 3050-Series Analyzers PN 305983902, Rev A

PN 305983902, Rev A
Overview
About This Document
This document describes the Essential Health and Safety requirements (EH&S)
for the AMEVision Display User Interface intended for use in explosive atmo-
sphere locations (Zone 1).
The procedures and information discussed in this document include only ab-
breviated steps to install, operate, and perform maintenance on the
AMEVision User Interface Display. They do, however, include all relevant safety
warnings and cautions to ensure the safety of personnel, the analyzer, and the
AMEVision Display User Interface in explosive atmosphere locations.
AMETEK takes great eort to ensure that its translations of docu-
ments into foreign languages are accurate and complete. However,
in the case of any discrepancies between the English version and the
translated version, the original English version shall take precedence.
AMETEK will not assume liability for any such discrepancies, or issues
arising from them.
Essential Health and Safety |1

PN 305983902, Rev A
Important Safety Information
Warnings, Cautions, Notes
WARNINGS, CAUTIONS, and NOTES contained in this manual emphasize critical
instructions as follows:
An operating procedure which, if not strictly observed, may result in
personal injury or environmental contamination.
An operating procedure which, if not strictly observed, may result in
damage to the equipment.
Important information that should not be overlooked.
Burn hazard. Hot surface. Do not touch, allow to cool before servicing.
Warning Labels
These symbols may appear on the instrument to alert you of existing condi-
tions.
Protective Conductor Terminal
(BORNIER DE L’ECRAN DE PROTECTION)
Schutzerde
Caution – Risk of electric shock
(ATTENTION – RISQUE DE DÉCHARGE ÉLECTRIQUE)
Achtung – Hochspannung Lebensgefahr
Caution – Refer to accompanying documents
(ATTENTION – SE RÉFERER AUX DOCUMENTS JOINTS)
Achtung – Beachten Sie beiliegende Dokumente
CAUTION – Hot Surface
(ATTENTION – SURFACE CHAUDE)
Achtung – Heiße Oberäche
2 | AMEVision Zone 1, for 3050-Series Analyzers

PN 305983902, Rev A
Special Conditions for Safe Use
The AMEVision Display User Interface is designed to be used in Category 2
hazardous locations where explosive gases may be present. Protection against
explosion is provided by a ameproof enclosure.
Do not open the enclosure when an explosive atmosphere is present
until the power is removed and the area is demonstrated to be non-
hazardous.
Verify ground continuity of all equipment before applying power. For
electrical shock protection, the AMEVision Display must be operated
from a grounded power source that has a securely connected protec-
tive ground contact.
Entry to the equipment must be made using suitably certied
Ex d IIB+ H2Gb entry devices.
Unused entry holes must be tted with suitably certied
Ex d IIB+ H2Gb blanking elements.
HAZARDOUS LOCATION LIMITATIONS
The AMEVision is a Category 2 analyzer specically designed and certied for
use in ATEX II 2 G hazardous locations. It can be safely operated in a location in
which:
• No gases are present with a higher probability of ignition than hydrogen
(e.g., acetylene).
• The ambient temperature does not exceed 60 °C.
• Voltages are 104–127 VAC or 230 VAC, 40 VA. The unit has been tested to
230 VAC ± 10 %.
Make sure the location in which the AMEVision Display is installed
meets all of the Hazardous Location Limitation criteria for a
Category2 analyzer described above.
Essential Health and Safety |3

PN 305983902, Rev A
Electrical Safety
Always shut down power source(s) before performing maintenance or trouble-
shooting. Only a qualied electrician should make electrical connections and
ground checks.
Any use of the equipment in a manner not specied by the manufacturer may
impair the safety protection originally provided by the equipment.
Grounding
Instrument grounding is mandatory. Performance specications and safety
protection are void if instrument is operated from an improperly grounded
power source.
Verify ground continuity of all equipment before applying power.
External Grounding Lug.
External Grounding Lug
Unit must be grounded.
4 | AMEVision Zone 1, for 3050-Series Analyzers

PN 305983902, Rev A
Environmental Information (WEEE)
This AMETEK product contains materials that can be reclaimed and recycled. In
some cases the product may contain materials known to be hazardous to the
environment or human health. In order to prevent the release of harmful sub-
stances into the environment and to conserve our natural resources, AMETEK
recommends that you arrange to recycle this product when it reaches its
“end of life”.
Waste Electrical and Electronic Equipment (WEEE) should never be disposed
of in a municipal waste system (residential trash). The Wheelie Bin marking
on this product is a reminder to dispose of the product properly after it has
completed its useful life and been removed from service. Metals, plastics, and
other components are recyclable and you can do your part by doing one of the
following steps:
• When the equipment is ready to be disposed of, take it to
your local or regional waste collection administration for
recycling.
• In some cases, your“end of life” product may be traded
in for credit towards the purchase of new AMETEK instru-
ments. Contact your dealer to see if this program is avail-
able in your area.
• If you need further assistance in recycling your AMETEK
product, contact us through our Customer Support page
at https://www.ametekpi.com/customersupport/request-
support.
Essential Health and Safety |5

PN 305983902, Rev A
This page intentionally left blank.
6 | AMEVision Zone 1, for 3050-Series Analyzers

PN 305983902, Rev A
Specications
AMEVision Display User Interface
Environment Ambient Temperature: -4 °F to 140 °F (-20 °C to +60 °C)
Relative Humidity: 5 % to 95 %, non-condensing
Maximum Altitude: 5000 meters
Power Requirements 15 VAC, ±10 %, 47–63 Hz, 40 VA max.
115 or 230 VAC, ±10 %, 47–63 Hz, 40 VA max.
Enclosure Flameproof Aluminum
Essential Health and Safety |7

PN 305983902, Rev A
This page intentionally left blank.
8 | AMEVision Zone 1, for 3050-Series Analyzers

PN 305983902, Rev A
Approvals and Certications
System Compliance
EMC Directive 2014/30/EU
Safety Directive 2014/35/EU
Figure 1.
AMEVision Display User
Interface label.
AMEVision Display User Interface Rating Label
II 2 G
AmeVision DISPLAY USER INTERFACE
Class B
FOR HAZARDOUS LOCATION
UNIT. REFER SERVICING TO QUALIFIED PERSONNEL.
NO USER SERVICEABLE COMPONENTS INSIDE
47-63 Hz. 40 VA max.
115-230 VAC +/- 10%
EMC
!
Group 1
OPERATING VOLTAGE
USE MIN. 90°C COPPER CONDUCTORS.
WARNING
-20°C ≤ Ta ≤ 60°C
Ex db IIB+H2 T6 Gb
DISCONNECT POWER OR ENSURE AREA
IS NON-HAZARDOUS BEFORE OPENING.
WARNING: BATTERY MUST BE REPLACED WITH
AMETEK PART NUMBER 1000-652-JE
ITS16ATEX101089X
RU C-US.ГƂ05.B.00824
~
2460
IECEx ETL 16.0030X
S
KTL 19-KA4BO-0157X
Essential Health and Safety |9

PN 305983902, Rev A
This page intentionally left blank.
10 | AMEVision Zone 1, for 3050-Series Analyzers

PN 305983902, Rev A
Installing the AMEVision Display User Interface
Pre-Installation Requirements
Before installing, operating, or servicing the 3050-Series Analyzer or
AMEVision Display User Interface, and before opening either device at any
time after they have been in operation, read and follow all Warnings, Cau-
tions, and Notes in this document and in this document and the analyzer User
Manual. This information contains important safety and general information
about the AMEVision Display unit and the analyzer.
The Zone 1 version of the AMEVision Display unit is designed to comply with
requirements for use of electrical equipment in Zone 1 classied hazardous
areas.
Read this entire section before beginning installation of the AMEVision
Display unit. Failure to do so, and/or use in a manner not specied in
this manual, may impair the protection against re, electrical shock
and personal injury originally provided by this equipment.
The installation of the analyzer and AMEVision Display unit must be
in accordance with all of the customer (end user) and local regulatory
standards and procedures. There are no operator-serviceable compo-
nents inside the display unit. Refer service requirements to qualied
personnel.
Any electrical connections, adjustments, or servicing of the analyzer
should be performed only by personnel properly trained and qualied
in that type of protection.
All electrical connections, materials, and methods (plus all safety stan-
dards and procedures) must be made in compliance with local wiring
regulations and electrical code for the hazardous area, as specied by
the owner company, local electrical inspection authority, and Nation-
al/EU regulations.
Essential Health and Safety |11

PN 305983902, Rev A
For electrical shock protection, the analyzer must be operated from
a grounded power source that has a securely connected protective
ground contact.
For AC electrical supply cable and conduit requirements refer to, and
comply with, local wiring regulations and electrical codes for the
hazardous area.
Never service the AMEVision Display User Interface or open its enclo-
sure when an explosive atmosphere is present until power has been
removed from both analyzer and AMEVision Display unit and the area
is demonstrated to be non-hazardous. Also, always use gloves when
working on the analyzer.
Installation drawings found in this section are for typical installations.
Customer drawings supplied with the system supersede the drawings
included here.
Personnel Technical Level Required for Installation
Installation must be performed by trained and qualied persons in ac-
cordance with local codes and NEC and CEC codes, where applicable.
Prior to installation, consult the local codes to understand what is
acceptable. To the extent this information is not consistent with local
codes, the local codes should be followed. AMETEK recommends
that only trained personnel perform these installation steps.
12 | AMEVision Zone 1, for 3050-Series Analyzers

PN 305983902, Rev A
AMEVision Display Site Location
Consider the following guidelines when selecting the location to install the
AMEVision Display User Interface:
• Select a readily accessible location for the analyzer and AMEVision Display
unit to allow for routine maintenance.
• Consider comfort levels for maintenance personnel when selecting place-
ment of the AMEVision Display unit.
Unpacking and Inspecting the Equipment
Remove any packing material from the AMEVision Display User Interface.
Check for damage and check contents against packing list. If equipment is
damaged, notify the carrier and contact AMETEK Service
(https://www.ametekpi.com/customersupport/requestsupport) immediately
if parts are missing or damage is found, and to verify if damaged parts will
require replacement prior to safely installing and operating the analyzer and
AMEVision Display unit.
Essential Health and Safety |13

PN 305983902, Rev A
Mechanical Installation
AMEVision Display User Interface Overview
The AMEVision Display User Interface used with 3050-Series Analyzers in
Zone1 Hazardous Locations. The AMEVision Display unit is housed in a ame-
proof enclosure that allows access to the controller keypad once the area is
determined to be clear of hazardous or explosive gases.
User Interface
Keypad
Display Hazloc Label
Wiring Label
Serial
Number
Label
Entries
Figure 2.
Explosion-Proof AMEVision
Display front and bottom
views.
14 | AMEVision Zone 1, for 3050-Series Analyzers

PN 305983902, Rev A
AMEVision Software Display and Keypad
The 3050-Series Analyzers are congured, calibrated, and monitored via the
MODBUS RTU interface. AMETEK provides two options for communicating
with the 3050-Series Analyzers:
• 3050 Congurator Software (via a PC, provided with each unit).
• AMEVision Display User Interface.
The AMEVision Display User Interface is an optional means of controlling the
3050-Series Analyzers and includes:
• 4.2" color, 1/4 VGA display.
• 19-key keypad.
• Web interface (TCP/IP) and modbus (RTU).
• Trend Data Logging/charting screen.
• USB port inside for rmware downloads and data uploads.
Basic Elements of the AMEVision Display Unit
• AMEVision Display Screen
The menu display is a three dimensional graphical user interface accessed
using the navigation Arrows and the ENTER/MENU key. These keys allow
you to cycle through the icons and to select the required menu option.
• Controller and Keypad
The control unit is operated by pressing the arrows and buttons on the
keypad. ENTER/MENU selects the selected option and Cancel exits the
option. The numeric keypad is used to enter information in the elds. Navi-
gation arrows are used to move throughout the display.
Essential Health and Safety |15

PN 305983902, Rev A
Accessing the Keypad on the Explosion-Proof Unit
To access the user keypad and controller:
• Ensure that the atmosphere is clear of any explosive gases and is safe.
• Unscrew the glass face on the front of the AMEVision Display unit.
Figure 3.
AMEVision User Interface
Display as seen inside
explosion-proof enclosure.
Keypad
Assembly
LCD Display
LCD
Capture Plate
Host Interface
Connector PCB
16 | AMEVision Zone 1, for 3050-Series Analyzers