Ametek Reichert Tono-Vera User manual

QUICK START GUIDE
Tonometer
Tono-Vera
®

Flexi-Soft™
Forehead Rest
Adjustment Wheel
Getting to Know Tono-Vera ® Tonometer
Tono-Vera®
Probe Chamber
Manual
Measure
Button
Display
Canthus
Mark
Battery Pack
Release
Battery Pack
Release
Tono-Vera® Probe
Chamber Collar
Multifunction
Buttons Canthus
Mark
USB-C Charging Port
(Rechargeable Model Only)
Menu Button
Flexi-Soft
Forehead Rest

Setting Up Tono-Vera Tonometer
Rechargeable Battery Model
Slide the Tono-Vera®Li-Ion Rechargeable Battery
Pack into the device until it clicks into place.
Plug in the Tono-Vera Charging Base and
place Tono-Vera on the base to charge.
Insert the batteries into the Tono-Vera AA Battery
Pack and slide it into the device until it clicks into
place.
AA Battery Model
Ocu-Dot®Probe Storage
Open the Ocu-Dot®Tonometer
Probes - 100 Count box and fold
the flap back along the side.
Load the Ocu-Dot Probe box with the tray into
the rear of the base.
Push the Ocu-Dot Probe tray fully into the base.
Power On/O
Press any button to turn Tono-Vera on.
To turn o, press and hold the center
Multifunction Button for three seconds.

Loading the Probe Main Screen
Remove Ocu-Dot
Probe Tube Cap.
Insert Ocu-Dot
Probe Tube into
Probe Chamber.
Rotate the unit so
the Ocu-Dot Probe
slides into the Probe
Chamber.
Store Ocu-Dot Probe
Tube in Tono-Vera
Base recess.
Battery Indicator
Probe Angle Indicator
OS (Left Eye)
OD (Right Eye)
Select OD/OS
Buttons
Menu
Alignment Target
Number of
Measurements
ActiView™Positioning
System Area
Measure Mode
1 2

15°
15°
Correct Probe Angle Incorrect Probe Angle
Tono-Vera Tonometer will automatically measure when properly aligned. It is suggested to practice
measuring with the included Tono-Vera Training Aid.
It is recommended to hold the unit so the Ocu-Dot Probe and Canthus Marks are perpendicular to the
eye. The unit can measure when the probe angle is ±15º from level. The probe tip should be approximately
4-8 mm from the eye. Extend the Flexi-Soft™ Forehead Rest to assist with positioning by rotating the
Flexi-Soft Forehead Rest Adjustment Wheel.
3Positioning
Approx.
4-8 mm
Device Orientation
Tono-Vera can be rotated a full 360º around the axis of
the Ocu-Dot Probe, as long as the probe is kept parallel
to the ground, within the ±15º probe angle range.

Correct distance, centration, and probe angle must be achieved simultaneously. The on-screen
ActiView™ Positioning System guides the user to proper alignment. When the proper distance,
centration, and probe angle are achieved, measurements will be taken automatically.
Distance & Centration (Approximately 4-8 mm)
A ring will appear when an eye is detected. The ring size is determined by distance, the ring color is
determined by both distance and centering. A beep will sound and a stop sign will appear when the unit
is too close to the eye.
Probe Angle
The Probe Angle Indicators aid in obtaining the proper probe angle. Tono-Vera is able to measure
within a probe angle range of ±15º. The color and position of the Probe Angle Indicators represent
whether the unit is in or out of the probe angle tolerance. The device will not measure if the device
is outside of the ±15º probe angle range.
Small Yellow Ring:
Too Far and/or O-Center
Yellow Probe Angle Indicators:
Probe Angle Too High
Green Ring:
Proper Distance
and Centration
Green Probe Angle Indicators:
Proper Probe Angle Alignment
!
Large Red Ring:
Getting Too Close
Beep Will Sound
Large Red Stop Sign:
Too Close
Beep Will Sound
4Aligning
Yellow Probe Angle Indicators:
Probe Angle Too Low

Clearing
Action Screens
To clear all data, press the Clear Button (×).
To clear data for one eye only, press the
corresponding Select and Clear OD/OS Button.
When taking measurements, the following
screens may appear, prompting action.
See Instructions for Use for more detailed
information.
A blue circle indicates the active eye being measured.
The dots indicating the Number of Measurements will
fill in as each measurement is taken.
After completing measurements for an eye, the Final
IOP Result will be briefly displayed in the center of
the screen. The result will remain inside the OD or
OS ring until cleared. The color of the ring around
the Final IOP Result indicates the reliability of the
measurement.
14.5
Too Far
from Eye
Final IOP Result - OD
Selected Eye - OS
Select and Clear
OD/OS Buttons
Clear
Number of
Measurements
Understanding Results
14.5
OD
8.7
OD
OD
High-Confidence Result
Final IOP Result appears
in a green ring.
Low-Confidence Result
Final IOP Result appears
in a yellow ring.
Retake Measurement
No IOP Result will appear
in an orange ring.
5 6
Measuring
Clean Probe
Chamber
Load
Probe

10.210.4
OD
Last
Measurement
OS
Menu Screen
For additional information and
translations, refer to Instructions for
Use on the included USB drive or
scan here:
Manufactured by:
Reichert, Inc.
3362 Walden Avenue, Suite 100
Depew, NY 14043 USA
Toll Free: 888-849-8955
Phone: [phone]
[email protected]
reichert.com
Reichert, Reichert Technologies,
Tono-Vera, and Ocu-Dot are registered
trademarks of Reichert, Inc.
ActiView and Flexi-Soft are trademarks
of Reichert, Inc.
AMETEK is a registered trademark
of AMETEK, Inc.
All other trademarks are properties of
their respective owners.
2023-01-12
16305-105 Rev. C
Access settings, information, and more.
Use the Navigation Buttons to cycle through screens.
Press Select to change the current selection.
The highlighted option displayed is the active selection.
To exit Menu Screen, navigate to Exit and press Select,
or press the Manual Measure Button at any time.
Navigation
Buttons
Select
Selected
(White)
Not Selected
(Grayed Out)
Menu
Title