Ametek Sorensen XTR Series User manual

Part Number M370046-04 Rev E January 2009 © 2007-2009 AMETEK Programmable Power, Inc. All rights reserved. www.programmablepower.com
QUICK REFERENCE GUIDE: XTR 850 Watt Series Programmable DC Power Supply (firmware v1.09 and below)
The XTR is equipped with a rotary Adjust/Enter control to provide a streamlined front panel for faster setup. Set voltage and current quickly and
easily using the rotary Adjust/Enter control and the 9-position Mode control. The information provided in this Quick Reference Guide is for basic
usage of the front panel and for understanding the menu system. See the other side of this Quick Reference Guide for a map of the front panel
menu system. For complete information on the XTR, please refer to the XTR 850 Watt Series Programmable DC Power Supply Operating
Manual (Part number: M370046-01).
1. Rotary Adjust/Enter Control
2. Constant Voltage Mode LED
3. Model Identification Label
4. Output Voltage Display
5. Constant Current Mode LED
6. Output Current Display
7. Alarm Indicator LED
8. Output On/Off Button
9. AUX On/Off Button
10. 9-position Mode Control
VOLTS: Voltage Programming
AMPS: Current Programming
FLD: Foldback
PRT: Protection
SAV: Save User Setting Memory Locations
RCL: Recall User Setting Memory Locations
CAP: Current Analog Programming
VAP: Voltage Analog Programming
PGM: Programming
XTR Front Panel Controls, Displays, and Indicators XTR Rotary Adjust/Enter Control
General Procedures for Setting Up Features
• To select a mode, rotate the 9-position Mode control to the desired mode.
• To select the feature or setting, turn the rotary Adjust/Enter control to scroll through the different available settings of that mode.
• The settings appear on the output display.
• Press the rotary Adjust/Enter control to select the feature or setting.
• Set each value using the rotary Adjust/Enter control. When the value has been selected, press the Adjust/Enter control to commit the
updated value.
Setting the Output Voltage and Current Limit Using Tracking Mode
To access the tracking mode where new values take effect as the rotary Adjust/Enter control is turned:
1. Select VOLTS or AMPS on the 9-position Mode control. The set point will blink and the unit will be in coarse tracking mode.
• When VOLTS mode is selected, the voltage set point will blink in the output voltage display.
• When AMPS mode is selected, the current set point will blink in the output current display.
2. Use the rotary Adjust/Enter control to adjust the set point.
3. Press the Adjust/Enter control to use fine adjust tracking mode. The set point blinks faster when the unit is in fine tracking mode.
4. Use the rotary Adjust/Enter control to fine tune the set point.
5. Once the set point has been selected, press the Adjust/Enter control to exit tracking.

Front Panel Menu System (firmware v1.09 and below) Front Panel Display Messages
Legend:
Press rotaryAdjust/Enter control
when no modification of the
tracking value has been made.
Mode Control State
Setting/Value
Press rotaryAdjust/Enter control
Rotate rotaryAdjust/Enter control
VOL
CUR
FLD
PRT
SAV
RCL
CAP
VAP
PGM
Coarse Volt Pre-SetCoarse Volt Tracking
Fold Delay
Select Preset
Select Preset
OVP
UVP
Overheat Protection
Shutdown Logic
UVP Coarse Adjust UVP Fine Adjust
On/Off
1/0
USB
LAN
GPIB
RS-232
RS-485
Local Lock
Address (1-30)
Address (1-30)
On/Off
Data Rate
Data Rate
Off
Voltage Isolated
Voltage Non-Isolated
Resistive Isolated
Resistive Non-Isolated
Off
Voltage Isolated
Voltage Non-Isolated
Resistive Isolated
Resistive Non-Isolated
Current APG Level
Voltage APG Level
Address (1-30)
Address (1-30)
Address (1-30)
Voltage APG Level
Voltage APG Level
Voltage APG Level
Current APG Level
Current APG Level
Current APG Level
OVP Coarse Adjust OVP Fine Adjust
Fine Volt Pre-SetFine Volt Tracking
CV
CC
None
Fold Delay
Coarse Current Pre-Set Coarse CurrentTracking Fine Current Pre-SetFine Current Tracking
Slave Address (1-30)
0 Ne
g
ative Polarit
y
1 Positive Polarit
y
AnPR Analo
g
Pro
g
rammin
g
AS Power On Autostart
AvAS Auxiliar
y
Autostart
CAPr Current Analo
g
Pro
g
rammin
g
CLr Clea
r
CC Constant Current
CU Constant Volta
g
e
CRPC Coarse Current Pre-set Mode
CrPU Coarse Volta
g
e Pre-set Mode
CShr Current Share
(
same as CUrrShAr
)
Curr Current
CUrrShAr Current Share
(
same as CShr
)
deLa Fold Dela
y
FOLD Foldback
p
rotection tri
gg
ered
FLA Flash
FNPC Fine Current Pre-set Mode
FNPU Fine Volta
g
e Pre-set Mode
FLd Settin
g
u
p
Foldback tri
gg
e
r
gpib GPIB Interface
HbPS Data rate
(
Kb
p
s
)
In Interlock
LE C Current APG Level
LE U Volta
g
e APG Level
Loc Lock
LOCL Local
OCP Over Current Protection
O7P Over Tem
p
erature Protection
OUP Over Volta
g
e Protection
OvPF Over Volta
g
e Protection fine ad
j
ustment
OUPC OVP Calibration
OU7P Out
p
ut Protection
POL Polarit
y
PRO Protection mode
PSU Power Su
pp
l
y
Unit
r IS Isolated Resistive Analo
g
Pro
g
rammin
g
rCL Recall User Settin
g
Memor
y
Locations
RE Remote Pro
g
rammin
g
/Interface
rnIs Non-Isolated Resistive Analo
g
Sd Shutdown
sLa Slave Remote Interface
U Is Isolated Analo
g
Volta
g
e Pro
g
rammin
g
UN Is Non-Isolated Analo
g
Volta
g
e
UUP Under Volta
g
e Protection Coarse
UUPF Under Volta
g
e Protection Fine Ad
j
ustment
UAPr Volta
g
e Analo
g
Pro
g
rammin
g
UOL Volta
g
e
Part Number M370046-04 Rev E January 2009 © 2007-2009 AMETEK Programmable Power, Inc. All rights reserved. www.programmablepower.com