AMG AMG6781 User manual

AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page 1 of 8 AMG6781 Instruction Sheet D16272-
03.doc
AMG6781 Instruction
Manual
8 Channel Video Transmit Unit for a Singlemode Optical
Fibre Link
The AMG6781 is a standalone eight channel video transmit unit designed to transmit 8 video signals
over one Singlemode fibre.
The AMG6781 is designed to be powered using an AMG2003 standalone power supply.
The AMG6781 is designed to operate with AMG6782 or rackmount equivalent AMG6782R eight
channel video receive unit in a point to point configuration.

AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page 2 of 8 AMG6781 Instruction Sheet D16272-
03.doc
Contents
Introduction 3
Unit Functional Schematic..............................................................................................................3
Optical Connection.........................................................................................................................3
Connections 4
Video Input Connections................................................................................................................4
Optical Connections.......................................................................................................................4
Power Connection..........................................................................................................................4
Front Panel Indicators 5
Power LED ....................................................................................................................................5
Video Input LED’s..........................................................................................................................5
Fibre Optic LED’s...........................................................................................................................5
Physical Information 6
Dimensions....................................................................................................................................6
Mounting Details............................................................................................................................6
Removal / replacement from / to the Case......................................................................................6
Safety 6
Maintenance and Repair 6

AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page 3 of 8 AMG6781 Instruction Sheet D16272-
03.doc
Introduction
Unit Functional Schematic
The AMG6781 transmits up to 8 video
signals to the AMG6782.
Optical Connection
The AMG6781 is connected as illustrated below when used with an AMG6782R 8-channel receive
unit acting as a point to point system.

AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page 4 of 8 AMG6781 Instruction Sheet D16272-
03.doc
Connections
Video Input Connections
No. of channels.................................. 8
Connector.......................................... 75 ohm BNC Socket.
Input Impedance................................ 75 ohm terminated.
Input Level......................................... 1 volt p-p nominal
Frequency Response......................... 10Hz to 7MHz.
Optical Connections
PRIMARY OPTO OUT
Connector.......................................... LC/PC
Optical Fibre...................................... One fibre - Singlemode
Primary Optical Launch Power........... -5dBm
Wavelength........................................ 1310nm
Power Connection
Connector Type................................. 2.1mm screw lock long power jack –centre positive
Connector Partno............................... Switchcraft S761K, AMG G16125-00
Supply Voltage................................... 13.5 to 18.0 Volts DC.
Maximum Power ............................... 10 Watts

AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page 5 of 8 AMG6781 Instruction Sheet D16272-
03.doc
Front Panel Indicators
Power LED
Power................................................Green - unit powered
Off - no power applied to unit
Video Input LED’s
Video Present CH1-8.........................Green - video signal present on input BNC
R/G - channel present but no video on I/P BNC
Fibre Optic LED’s
Primary Opto Sync TX ....................... Green - optical channel transmitting
Off - optical channel not transmitting
Primary Opto Sync RX.......................Not used

AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page 6 of 8 AMG6781 Instruction Sheet D16272-
03.doc
Physical Information
Dimensions
Height................................................ 112mm
Width................................................. 170mm (excluding connectors)
Depth................................................. 70mm
Weight............................................... 1000grams
Mounting Details
The AMG unit is supplied with a clip-on mounting bracket which should be attached to a panel or wall
using 2 off 4.0mm screws, see diagram on page 1 for dimensions. The unit is clipped into the
mounting bracket, and is then held firmly in position.
Removal / replacement from / to the Case
Note: - The AMG unit PCB's are static sensitive. Handle with proper care and use normal electrostatic
discharge (ESD) procedures. Use properly grounded protection (for example, wrist straps) when
handling the PCB.
To remove units from the case to access the data expansion boards and the daughter boards, remove
the 2 or 4 fixing screws on the rear panel and slide the PCB's out of the case.
Ensure that the fibres do not snag or get trapped.
To replace the PCB's into the case, slide the PCB's gently into the case aligning the boards with the
appropriate slots. Ensure that the fibre do not snag or get trapped.
Safety
AMG Optical Fibre Products use Class 1 laser systems in accordance with EN 60825-2:2000.
It is always advisable to follow good practice when working with optical fibre systems. This includes:
§Do not stare with unprotected eyes or with any unapproved collimating device at fibre
ends or connector faces, or point them at other people.
§Use only approved filtered or attenuating viewing aids
For other safety issues and advice on good practice associated with optical fibre systems, please see
EN 60825-2:2000 or your local safety officer.
Maintenance and Repair
There are no user serviceable parts within AMG products. See unit data sheet for full specification.
In case of problem or failure, please call your local support centre or contact: AMG Systems Ltd. at
3 The Omega Centre, Stratton Business Park, Biggleswade, Beds., SG18 8QB, UK.
Phone [phone]
Technical Support [phone]
Email [e-mail]

AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page 7 of 8 AMG6781 Instruction Sheet D16272-
03.doc
This page is intentionally blank.

AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page 8 of 8 AMG6781 Instruction Sheet D16272-
03.doc
This page is intentionally blank.