AMP Research BedStep 2 User manual

www.amp-research.com 1/4 IM75406 rev 01.02.12
BedStep2™ is invented, designed, engineeried and manufactured exclusively by AMP Research and may be covered by one of the following patents:
6,641,158; 6,830,257; 6,938,909; 7,055,839; 7,380,807; 7,398,985; 7,584,975. Made in USA © 2011 AMP Research
Three-year limited warranty. Professional installation is recommended.
AMP RESEARCH TECH SUPPORT 1-888-983-2204 (Press 2) Monday - Friday, 6:00 AM - 5:00 PM PST
20-03797-10
19-03783-90 19-03341-90
11-03639-90
Dodge Ram DS
1500 (2009-Current)
2500/3500 (2010-Current)
19-03563-90
10-00115-60
Torque wrench
13 mm
PART NUMBER:
75406-01A
15 mm
T25
1/4” Drill Bit
3/8” Drill Bit
15-03833-90
16-03852-90
16-03850-90
15-03839-90
19-02389-90
1
For 6.5’ & 8’ bed lengths components must be configured for Passenger or Drivers-Side as
shown.
Passenger-Side Orientation
Driver-Side Orientation
NOTE: For Dually applications
see kit 75611-01A for proper
bracket orientation.
19-03037-90
For 5.5’ bed length components must be configured for Passenger or Drivers-Side as shown.
Driver-Side Orientation Passenger-Side Orientation

www.amp-research.com 2/4 IM75406 rev 01.02.12
15mm
13mm
4
4
56
A
B
Hole set A is to be used on 6.5’ and 8’ beds
Hole set B is to be used on 5.5’ beds.
23
Use supplied drill template (See page 4) and
mark holes in front bed channel mount. Pre drill
holes using 1/4” drill bit. Next drill hole to 3/8”.
Using a 15mm Socket assemble Lateral mount onto linkage. Steel bracket is to be assembled
between linkage and lateral mount. Do not tighten bolts yet. See Step 2 for bracket orientation
based on bed length.
NOTE: DRIVER SIDE SHOWN WITH 6.5’ & 8’ BED.
MIRROR FOR PASSENGER SIDE.
Using a 13mm socket assemble frame mount
onto Lateral mount. Tor que bolts to 16 ft-lbs.
Slide threaded plate into bed channel and line up
threaded locations to pre drilled holes.

www.amp-research.com 3/4 IM75406 rev 01.02.12
5
9
8
10
11 12
13mm
7
Using a 13mm Socket with extension, align bolts
with threaded plate. Tor que to 16ft-lbs.
Set bolts into lower lateral mount. Set bracket
into place and use provided hardware to bolt
bracket to inner bed brace.
Set linkage into position, tighten bolts using
15mm Socket. To r que to 20 ft-lbs.
Tighten bracket bolt with 13mm socket and
wrench. Torque to 16 ft-lbs.
13mm
13mm
Locate the step pad in the following positions
per application. Crew Cab 1500 offset step pad
rearward. All other applications mount step pad in
center position.
Verify step pad alignement to body line of vehicle.

www.amp-research.com 4/4 IM75406 rev 01.02.12
Center Template on bed chan-
nel and align edge up to vertical
reinforcement plate on edge of
bed channel.
To deploy the step, press down using your foot on
the outside edge of the step pad.
To retract, gently kick up on the underside of the step
pad.
13 14
Template for Step 3 on page 2.
Approx 4.10”
Align this edge up to vertical reinforcement
plate on edge of bed channel.