AMS TCS3720 User manual

Published by ams-OSRAM AG
Tobelbader Strasse 30, 8141 Premstaetten, Austria
Phone [phone]
ams-osram.com
© All rights reserved
TCS3720 EVM
Quick Start Guide
ALS/Color and proximity sensor for behind OLED applications

TCS3720 EVM
Table of contents
Eval Kit Quick Start Guide •PUBLIC •Document Feedback
QG001011 •v2-00 •2023-Dec-12
2 /9
/
Table of contents
1Out of the box................................................................. 3
2Software installation....................................................... 4
3Connect hardware........................................................... 6
4Start the application........................................................ 6
5Uninstall application ....................................................... 7
6Revision information....................................................... 8
7Legal information............................................................ 9

TCS3720 EVM
Out of the box
Eval Kit Quick Start Guide •PUBLIC •Document Feedback
QG001011 •v2-00 •2023-Dec-12
3 /9
/
1 Out of the box
For a detailed description of the TCS3720 EVM, please refer to User Guide:
•UG001018
Each TCS3720 Evaluation Kit comes with the following components:
Figure 1: Evaluation kit contents
No.
Item
Description
1
TCS3720 daughter card
PCB with TCS3720 sensor installed
2
EVM controller board
Used to communicate USB to I2C
3
USB cable (A to Micro-B)
Connects EVM controller to PC
4
Flash drive
Includes application installer and documents
2
3
4
1

TCS3720 EVM
Software installation
Eval Kit Quick Start Guide •PUBLIC •Document Feedback
QG001011 •v2-00 •2023-Dec-12
4 /9
/
2 Software installation
1. Plug the flash drive into an unused USB port
2. Double-click the Setup.exe file on the flash drive, or click Start > Run and type E:setup.exe
and press Enter. IMPORTANT: Use the appropriate drive letter in the above command to
install the software. Flash Drive will commonly be assigned the next available drive letter
for example C: hard drive, D: CD-ROM, E: flash drive
3. The Setup Wizard will open and guide you through the installation of the TCS3720 host
software, (Figure 2 through Figure 8 )
4. The EVM Controller board requires the installation of FTDI CDM drivers. If these drivers
are not installed on your machine, this setup will automatically launch the installer for the
FTDI drivers.
5. At the end of the installation, click Finish to exit the setup.
Figure 2: Welcome screen
Figure 3: Liability disclaimer

TCS3720 EVM
Software installation
Eval Kit Quick Start Guide •PUBLIC •Document Feedback
QG001011 •v2-00 •2023-Dec-12
5 /9
/
Figure 4: Select installation location
Figure 5: Select start menu folder
Figure 6: Installation in progress
Figure 7: Information screen

TCS3720 EVM
Connect hardware
Eval Kit Quick Start Guide •PUBLIC •Document Feedback
QG001011 •v2-00 •2023-Dec-12
6 /9
/
Figure 8: Installation completed successfully
3 Connect hardware
Plug the TCS3720 Daughterboard into the Controller board (Figure 1). Always use ESD
procedures when handling the EVM.
Using the enclosed USB cable, plug the micro-B connector into the EVM module. Using the
other end of the cable, plug the USB A-connector into a USB port on the computer.
When the USB cable is connected, the green LED should light on power up to indicate that
power is being received via the USB interface, and the controller board processor is running. If
the green LED does not light, check the USB cable connections; unplug the USB cable and try
again. If the green LED still does not light, check the PC for USB error messages. When the
software application is run, it will turn off the LED.
4 Start the application
To start the application select ams-OSRAM > TCS3720 EVM > TCS3720 EVM on the All
Programs menu. The default installation directory depending on the device and the operating
system you are using is:
C:\Program Files\ams-OSRAM\TCS3720_EVM (Windows 32-bit operating systems)
C:\Program Files (x86)\ams-OSRAM\TCS3720_EVM (Windows 64-bit operating systems)

TCS3720 EVM
Uninstall application
Eval Kit Quick Start Guide •PUBLIC •Document Feedback
QG001011 •v2-00 •2023-Dec-12
7 /9
/
A different install path may be selected by the user during the install (Figure 4). When started,
the TCS3720 window will open on the PC and automatically connect to the hardware.
5 Uninstall application
To remove the software from your computer (Figure 9), select
ams-OSRAM > TCS3720 EVM > Uninstall TCS3720 EVM or use the Windows control panel.
Figure 9: Remove installation

TCS3720 EVM
Revision information
Eval Kit Quick Start Guide •PUBLIC •Document Feedback
QG001011 •v2-00 •2023-Dec-12
8 /9
/
6 Revision information
Definitions
Draft / Preliminary:
The draft / preliminary status of a document indicates that the content is still under internal review and subject to change without notice. ams-OSRAM
AG does not give any warranties as to the accuracy or completeness of information included in a draft / preliminary version of a document and shall
have no liability for the consequences of use of such information.
Changes from previous released version to current revision v2-00
Page
Document contents were transferred to latest ams OSRAM design
●Page and figure numbers for the previous version may differ from page and figure numbers in the current revision.
●Correction of typographical errors is not explicitly mentioned.

TCS3720 EVM
Legal information
Eval Kit Quick Start Guide •PUBLIC •Document Feedback
QG001011 •v2-00 •2023-Dec-12
9 /9
/
7 Legal information
Copyright & disclaimer
Copyright ams-OSRAM AG, Tobelbader Strasse 30, 8141 Premstaetten, Austria-Europe. Trademarks Registered. All rights reserved. The material
herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner.
Demo Kits, Evaluation Kits and Reference Designs are provided to recipient on an “as is” basis for demonstration and evaluation purposes only and
are not considered to be finished end-products intended and fit for general consumer use, commercial applications and applications with special
requirements such as but not limited to medical equipment or automotive applications. Demo Kits, Evaluation Kits and Reference Designs have not
been tested for compliance with electromagnetic compatibility (EMC) standards and directives, unless otherwise specified. Demo Kits, Evaluation
Kits and Reference Designs shall be used by qualified personnel only.
ams-OSRAM AG reserves the right to change functionality and price of Demo Kits, Evaluation Kits and Reference Designs at any time and without
notice.
Any express or implied warranties, including, but not limited to the implied warranties of merchantability and fitness for a particular purpose are
disclaimed. Any claims and demands and any direct, indirect, incidental, special, exemplary or consequential damages arising from the inadequacy
of the provided Demo Kits, Evaluation Kits and Reference Designs or incurred losses of any kind (e.g. loss of use, data or profits or business
interruption however caused) as a consequence of their use are excluded.
ams-OSRAM AG shall not be liable to recipient or any third party for any damages, including but not limited to personal injury, property damage, loss
of profits, loss of use, interruption of business or indirect, special, incidental or consequential damages, of any kind, in connection with or arising out
of the furnishing, performance or use of the technical data herein. No obligation or liability to recipient or any third party shall arise or flow out of ams-
OSRAM AG rendering of technical or other services.
ams OSRAM semiconductor RoHS compliance statement
RoHS compliant: The term RoHS compliant means that ams-OSRAM AG semiconductor products fully comply with current RoHS directives. Our
semiconductor products do not contain any chemicals for all 6 substance categories plus additional 4 substance categories (per amendment EU
2015/863), including the requirement that lead not exceed 0.1% by weight in homogeneous materials.
Important information: The information provided in this statement represents ams-OSRAM AG knowledge and belief as of the date that it is
provided. ams-OSRAM AG bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to
the accuracy of such information. Efforts are underway to better integrate information from third parties. ams-OSRAM AG has taken and continues to
take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. ams-OSRAM AG and ams-OSRAM AG suppliers consider certain information to be proprietary, and thus CAS
numbers and other limited information may not be available for release.
Headquarters
ams-OSRAM AG
Tobelbader Strasse 30
8141 Premstaetten
Austria, Europe
Tel: [phone]
Please visit our website at ams-osram.com
For information about our products go to Products
For technical support use our Technical Support Form
For feedback about this document use Document Feedback
For sales offices and branches go to Sales Offices / Branches
For distributors and sales representatives go to Channel Partners