Bircher Reglomat Swissdoor PrimeMotion B User manual

1
PrimeMotion B
Observe the national and international regulations on door safety.
Only trained, qualified personnel may mount and start up the detector.
The unit may only be opened and repaired by Bircher Reglomat.
The unit may only be operated from a safety extra-low voltage (SELV) system with safe electrical separation.
Always consider the safety functions of your application as a whole, never just in relation to one individual section of the system.
The installer is responsible for carrying out a risk assessment and installing the detector and the door system correctly.
Avoid touching any electronic components.
The door drive and transom profile must be grounded correctly.
Start-up
2Montage
Translati n f the riginal instructi ns
Recommen e start-up sequence: I. Mounting II. Connection
Mounting
I
General
Safety instructions
1
Please keep for further use!
 Hood
 Light window detector indication
 no function
 Cable bushing
 Mounting holes
 Detector electronic
 Microwave module
 LED microw.: green
PrimeMotion B
1. Remove cover hood 2. Lay and connect cable 3. Mount detector
Radarfeld
Microwave motion detector for opening
automatically controlled doors
1. Position drill template
2. Drill the holes, remove drill template
3. Lay cable and mount detector
ENGLISH
Mounting of the detector
II
Electrical connections
Connecting
3
PrimeMotion B Controller
1 white
2 brown
3 green
4 yellow
Cable
white
brown
green
yellow
Power Supply 3 m
Radar
output*
–
+
11.5 - 36 VDC
12 - 28 VAC
Microwave
1
2
3
4
4 3 2 1
+
Mechanical fine tuning
4
––
++
Manual inclinati n settings
0° ... +45° in 5° steps
Manual inclinati n settings
– 20° ... +20° in 5° steps
––
++
1m
2m
0m
0m
1m
2m
3m
4m
Wi e ra ar fiel turn 90° Narrow ra ar fiel
min. = 0.16 x 0.8, max. = 2 x 4 m (WxD)
min. = 0.5 x 0.25, max. = 4 x 2 m (WxD)
+
1m
2m
0m
0m
1m
2m
3m
4m
–
nclination angle: 35° nclination angle: 35°
2.2 m
2.2 m
–


90°







* See also D P-switch-settings (Chap. 5)
289118I
12/16
Radar field

5Configuration by han DIP-Switch an potentiometer
Ra ar functions DESCRIPTION
Field size
1 = Smallest radar field (LED flashes once),
2 ......., 3* = Medium radar field (flashes 3 times),
4 ......, 5 = Largest radar field size (flashes 5 times)
Direction recognition
1
ON
2 3 4
ON = both directions
OFF* = forward
Cross Traffic Optimisation CTO
1
ON
23 4
ON = CTO on
OFF* = off
Door filter ( nterfence for radar)
1
ON
234
ON = Door and interference filter on
(EM interference, e.g. fluorescence tube)
OFF* = filter off
Radar output
1
ON
243
ON = passive (NC)
OFF* = active (NO)
2
1
ON
2 3 4
Radar output (active/passive, NO/NC)
nterference filter (Door and EM interference)
CTO and swing filter
Direction recognition
green LED Fault Reme y
continuously
lit
Radar tripping when door is closing 1. Set angle of radar further away from the door.
2. Adjust radar field size.
Radar false tripping without
apparent external influence
1. Avoid light sources (e.g. fluorescent tubes) in the immediate vicinity of the detector.
2. No moving objects (plants, advertising posters, etc.) in the vicinity of the detector.
3. Avoid strong vibration at the radar detector
4. Possible influence from a second radar detector in the vicinity (very unlikely)
I entification of the year of manufacture
8.2
Smallest radar field Largest radar field
medium radar field
Potentiometer
DIP-Switch
The Slow Motion Detection (SMD) i a factory etting. The SMD recogni e low motion after the detecor ha been activated.
Year, month, day
Troubleshooting
6
Technical ata
7
Technology Double field module, 24.125 GHz
Mounting height 1.8 - 4 m
Electrical power supply ≤120 mA @ 11.5 – 32 VDC, 12 – 28 VAC
Power consumption < 4 watts
Making current ≤800 mA
Radar output
Solid State Relay
max. contact voltage: 48V (AC) / 48V (DC), max. contact-resistance: 30 Ohm
max. load current: 80mA, max. switching capacity: 500mW (AC) / 500mW (DC)
Protection type Suitable for use acc. to P54
Operating temperature -20° to 60° C
Dimensions 172 x 60 x 48 mm (LxWxD)
Weight 120 g
Declaration of conformity, i entification of the year of manufacture by means of the serial number
8
9Contact information
Manufacturer:
Bircher Regl mat AG
Wiesengasse 20
CH-8222 Beringen
www.bircher-regl mat.c m
Declaration of conformity
8.1
Manufacturer: Bircher Reglomat AG, Wiesengasse 20, CH-8222 Beringen
Following directives have been observed: RoHS 2011/65/EU, RED 2014/53/EU, EMC 2014/30/EU
Product variant: PrimeMotion B
* factory settings
Danish seller:
Swissdoor ApS
Stenhuggervej 2
DK-5471 Søndersø
[email protected]
www.swissdoor.dk