LEGRAND 0 489 59 User manual

1/7
CONTENTS
PIR presence detector for high bay
applications - ON/OFF
Technical data sheet: S000105276EN-1 Updated: 01/02/2019 Created: 27/11/2018
Cat. No(s): 0 489 59
128, av. du Maréchal-de-Lattre-de-Tassigny - 87045 LIMOGES Cedex
Tel: [phone] Fax: [phone]
www.legrand.com
CONTENTS Page
1. Use ......................................1
2. Technical characteristics .................1
3. Dimensions..............................2
4. Connection ..............................2
5. Installation ..............................2
6. Operation ...............................4
7. Settings .................................5
8. Performance.............................7
9. Care .....................................7
10. Standards ...............................7
1. USE
This PIR (passive infrared) presence detector provides automatic control
of lighting loads with optional manual control.
It is a high sensitivity PIR detector suitable for high bay applications,
such as warehouses and factories, and where high detection sensitivity
is needed.
The unit detects movement using a PIR sensor and turns the load on.
When an area is no longer occupied, the load will switch off after an
adjustable timeout period.
The output channel includes a mains voltage switching relay for ON/OFF
control of lighting.
The unit can turn lights on when a room is occupied and off when
the room is empty. Optional settings allow lights to be turned off in
response to ambient daylight.
These units come complete with accessories that allow changes to the
detection area and surface mounting
All functionality is fully programmable using an infrared configurator.
2. TECHNICAL CHARACTERISTICS
PIR sensor
Detects movement within the unit’s detection range, allowing load
control in response to changes in occupancy.
IR receiver
Receives control and programming commands from the infrared
configurator.
Light level sensor
Measures the overall Lux level in the detection area.
LED status
The LED flashes red to indicate the following:
Walk test LED active When movement is detected
Valid setting received
2. TECHNICAL CHARACTERISTICS CONTINUED
Dimensions See dimensions section
Weight 0.2 kg (complete unit)
Power supply 230 VAC +/-10%
Frequency 50 Hz
Maximum load
6 A resistive and incandescent lighting
6 A fluorescent lighting
6 A compact fluorescent lighting
6 A low-energy lighting
6 A low-voltage lighting (switches
transformer primary)
6 A fans and ventilation equipment
Power consumption ON 822 mW, OFF 847 mW
Terminal capacity 2.5 mm2
Operating temperature -30°C to +35°C
Operating humidity 5 to 95% non-condensing
Material Flame-retardant ABS and PC/ABS
Type Class 2
Protection class IP40 without gasket and IP65 with
gasket

2/7
CONTENTS
PIR presence detector for high bay
applications - ON/OFF
Technical data sheet: S000105276EN-1 Updated: 01/02/2019 Created: 27/11/2018
Cat. No(s): 0 489 59
3. DIMENSIONS
Detector
Surface mounting accessory
4. CONNECTION
Wire the products as shown in the diagram.
The auxiliary switch is optional. It can be used to switch the lighting on
and off.
N
L
L/Out
Absence detection mode
To use absence detection, a push-button must be connected between
the 2 terminals on the diagram (mains voltage switching).
The unit ships with presence detection as default. To change to absence
detection, press and release the push-button 5 times within a minute
of power-up. The LED lights up for 30 seconds to indicate that absence
detection mode has been selected.
To change back to presence detection, repeat the above procedure: the
LED flashes for 30 seconds to indicate that presence mode has been
selected.
Note: The above adjustments can also be made using the infrared
configurator.
5. INSTALLATION
The product is designed to be mounted on the ceiling (surface or flush
mounting), using the accessory provided.
Use the supplied gasket to ensure IP65 rating (not compatible with
surface mounting).
For optimum operation of the lux sensor, the lens must be shielded as
much as possible from the light source.
Avoid direct sunlight being aimed at the sensor.
Do not site within 1 m of forced air heating or ventilation.
Do not fix to a vibrating surface.
Flush mounting
ø 64 mm
ø 30 mm hole max
Pull out spring tab and rotate
spring arm as shown
Take care not to
bend the springs
when tting the unit
50 mm or 60 mm xing
centres
ø 64 mm
ø 30 mm hole max
Pull out spring tab and rotate
spring arm as shown
Take care not to
bend the springs
when tting the unit
50 mm or 60 mm xing
centres

3/7
CONTENTS
PIR presence detector for high bay
applications - ON/OFF
Technical data sheet: S000105276EN-1 Updated: 01/02/2019 Created: 27/11/2018
Cat. No(s): 0 489 59
5. INSTALLATION CONTINUED
Surface mounting
ø 64 mm
ø 30 mm hole max
Pull out spring tab and rotate
spring arm as shown
Take care not to
bend the springs
when tting the unit
50 mm or 60 mm xing
centres
ø 64 mm
ø 30 mm hole max
Pull out spring tab and rotate
spring arm as shown
Take care not to
bend the springs
when tting the unit
50 mm or 60 mm xing
centres
ø 64 mm
ø 30 mm hole max
Pull out spring tab and rotate
spring arm as shown
Take care not to
bend the springs
when tting the unit
50 mm or 60 mm xing
centres
Power-up test procedure
When power is applied to the unit, the load will turn on immediately.
Set the timeout to 10 seconds, vacate the room or remain very still and
wait for the load to switch off.
Check that the load switches on when movement is detected.
The unit is now ready for programming.
5. INSTALLATION CONTINUED
Troubleshooting
If the load does not turn ON:
− Check that the live supply to the circuit is correct.
− Check that the load is functioning by bypassing the sensor
(link terminals L and L/Out).
− If the detection range is smaller than expected, see the
Performance section. Rotating the sensor slightly may
improve the detection range.
If the load does not turn OFF:
− Ensure that the area is left unoccupied for longer than the
timeout period.
− Ensure that the detector is not affected by circulating air,
heaters or lamps.
In the event of “false tripping”, reduce the sensitivity settings.
Alignment marks
The sensor head has 4 alignment marks. These correspond to the
4 passive infrared sensors under the lens.
Use these marks to align with aisles and corridors to ensure the best
detection characteristics.
Masking
The unit also ships with two clip-on masking shields to allow for precise
masking of the detection shape.
The masks can be easily shaped to produce detection patterns suitable
for applications such as aisles and corners and for narrowing the
detection diameter.
Important notes:
• Ensure all infra-red (IR) programming is completed
before affixing the masking shields to the detector.
• The masking shields may impair the light sensor and
IR sensors by covering them. Ensure correct operation
before completing commissioning. Ensure correct
operation before completing commissioning.

4/7
CONTENTS
PIR presence detector for high bay
applications - ON/OFF
Technical data sheet: S000105276EN-1 Updated: 01/02/2019 Created: 27/11/2018
Cat. No(s): 0 489 59
5. INSTALLATION CONTINUED
Masking shields trimmed for aisle-shaped detection
6. OPERATION
Detection mode
Presence: When movement is detected the load will automatically
turn on. When an area is no longer occupied, the load will switch off
automatically after an adjustable time period.
Absence: The load is manually switched on. When an area is no longer
occupied, the load will switch off automatically after the adjustable time
period has elapsed.
Manual control: short press to turn on, short press to turn off, press and
hold for dimming cycle.
In either case, sensitivity to movement of the PIR sensor can be adjusted
using the Sensitivity parameter.
HINT: To assist in setting the sensitivity, turn on the Walk test LED which
will flash red when movement is detected.
Switching according to Lux level
Occupancy detection can be made dependent on the ambient light level
using the Lux On Level and Lux Off Level parameters.
Switch on Switch o
Occupation
détectée
Brighter
Darker
Lux O level
Lux On level
Lighting level
Lux time
**
*
Occupancy
detected
Marker
No.
Masking shield %
coverage
1 45%
2 32%
3 22%
4 11%
Marker No. 1 2 3 4 4 3 2 1
Align trimmed shields with the sensor head alignment mark and aisle.
Example:
Fixing height = 6 m
Slot number = 2
Aisle detection width (walk across) = 16 m x 32% = 5.1 m
Aisle detection width (walk towards) = 12 m x 32% = 3.8 m
Masking shields trimmed for a narrow beam of detection
Example:
Fixing height = 15 m
Diameter number = 3
Aisle detection width (walk across) = 40 m x 45% = 18 m
Aisle detection width (walk towards) = 30 m x 45% = 13.5 m
Diameter No: 1 2 3 4 5 5 4 3 2 1
Diameter
No.
Masking shield
% coverage
1 89%
2 63%
3 45%
4 32%
5 22%

5/7
CONTENTS
PIR presence detector for high bay
applications - ON/OFF
Technical data sheet: S000105276EN-1 Updated: 01/02/2019 Created: 27/11/2018
Cat. No(s): 0 489 59
7. SETTINGS
The detector functions are controlled by a number of parameters which can be changed or programmed by an infrared configurator.
In combination with configuration tool 0 882 40, the Legrand Close Up smartphone app can be used to view and modify all the detector parameters with
online help.
Point the infrared configuration tool at the detector and send the necessary programming commands to the unit as indicated in the table below.
Valid commands will be indicated by a red flashing LED.
Parameter Default
value Range/option Description
Detection parameters
LED operation test Off On or Off When this option is activated, a red LED on the sensor flashes when it detects
movement. Use this function to check that the sensitivity levels are suitable.
Timeout 20 minutes 0 to 99 minutes Once the detector is turned on, this value sets how long the lights will stay on once
movement has ceased. Select 0 for a 10-second period (for commissioning only).
Manual timeout period 10 minutes 0 to 99 minutes
When a manual operation occurs, either via the switch input or the infrared, it invokes
the timeout period.
Example 1: a detector in presence mode has a detector timeout of 15 minutes and
a manual timeout of 3 minutes. When the user leaves the room, they press the off
button. The sensor will revert to automatic mode after 3 minutes. Walking back into
the room will turn the lights on.
Example 2: using the settings above, the user turns the lights off (say for a
presentation) but stays in the room. Every time a movement is detected, the manual
timeout period is re-triggered, but if it doesn’t pick up over a short period, the
detector will revert to automatic mode. This means that the lights may come on
inadvertently during the presentation, even if the occupants are still present during
the manual timeout period, so adjust the timing carefully.
Sensitivity On 91 (min) to 9 (max) Sensitivity level for detecting movement when the detector is already on.
Sensitivity Off 91 (min) to 9 (max) Sensitivity level for detecting movement when the detector is off.
Lux time 00 (disabled)
1 to 99 minutes
If the detector measures the Lux level and decides that the output needs switching
on or off as a consequence, the Lux time must elapse first. If at any time during the
timed delay the Lux change reverses, the process is cancelled. Lux time enables
absence detection to be implemented with a Lux Off level set. When the button
is pressed, the lights will go on, regardless of ambient light level. However, if there
is sufficient ambient light, they will turn off again after the Lux time. Note that
whenever an external switch is pressed, whether in absence or presence mode, if the
lights were out because of the Lux level, they will be immediately turned on again
for at least the Lux time.

6/7
CONTENTS
PIR presence detector for high bay
applications - ON/OFF
Technical data sheet: S000105276EN-1 Updated: 01/02/2019 Created: 27/11/2018
Cat. No(s): 0 489 59
7. SETTINGS CONTINUED
Parameter Default
value Range/option Description
Power-up state On On or Off Select Off for a 30-second delay on start-up. If On is selected, there will be no delay
on start-up and the detector will always power up detection.
Inhibit 4 seconds 1 to 999 seconds
When the detector turns off, a delay is instigated to prevent retriggering. In certain
circumstances this delay may not be enough. This parameter allows the delay to
be changed.
Verify No No or Yes Requires two or more PIR detectors to detect simultaneously to turn on the lights.
Factory default - - Restores the factory default settings.
User Modes
Override On - - If the lights are off, sending the IR command will turn them on immediately and
revert to automatic operation after the manual timeout period.
Override Off - - If the lights are on, sending the IR command will turn them off immediately and
revert to automatic operation after the manual timeout period.
Cancel - - Cancels the on or off override, returning the detector to normal operation.
Channel 1 - Switching
Lux On level
9
1 to 9
For a higher
resolution a range of
101-199 is available
Sets a minimum light level below which the PIR sensor is enabled, allowing the
lights to be turned on by movement.
Note: The "Lux Off level" value must always be greater than the "Lux On level”value.
Lux Off level Sets a maximum light level above which the PIR sensor is disabled, preventing the
lights from being turned on by movement.

7/7
CONTENTS
PIR presence detector for high bay
applications - ON/OFF
Technical data sheet: S000105276EN-1 Updated: 01/02/2019 Created: 27/11/2018
Cat. No(s): 0 489 59
8. PERFORMANCE
Detection area
Walk across
Walk towards
9. CARE
Keep the lens clean, use a cloth to clean the surface.
Do not use acetone, tar-removing cleaning agents or trichloroethylene.
10. STANDARDS
Directive: CE
Installation standards: NFC 15-100
Product standards: NF EN 60730-1
Environmental standards:
− European Directive 2012/19/EU: WEEE (Waste Electrical and
Electronic Equipment)
− European Directive 2011/65/EU: RoHS (Restriction of
Hazardous Substances)
− Decrees and/or regulations: Public buildings, workplace
buildings, high-rise buildings
Conformity
− EMC-2014/30/EU
− LVD-2014/35/EU
CAUTION: Always test before using other special cleaning
products.
Height Diameter
15 m 40 m
10 m 26 m
6 m 16 m
3 m 9 m
Height Diameter
15 m 30 m
10 m 20 m
6 m 12 m
3 m 8 m
40 m
15 m (20 m max)