AMTC HY-GENIE ASD-600 User manual

™
ASD-600 HY-GENIE™
AUTOMATIC LIQUID SANITIZER DISPENSER
INSTALLATION & OPERATION MANUAL
Page 1 of 4
READ BEFORE INSTALLATION:
During the initial installation you may
need to prime the sanitizer 4-5 times to get
the liquid to pump through the spout.
In some cases there may be some
trapped air in the system that does not allow
the sanitizer to initially prime. If this is the case
you will need to blow through the sanitizer filter
to clear the trapped air. Then prime the sanitizer
again. The sanitizer should now prime through
the spout.
For further assistance please call
Technical Support at 1-800-874-7822.
IMPORTANT PRE-INSTALLATION NOTE
Sanitizer Filter

Installation Diagram
™
Installation Instructions (refer to installation diagram above)
Battery Pack
4-D Size
(Batteries Sold Separately)
Reset Button
Liquid Sanitizer Bottle
(800 mL)
Spout
Spacer Sensor Cable
Mounting Bracket
Countertop or Sink
Max. Thickness: 2” (50mm)
AD05
6 Volt AC Power Adapter
(Optional-Sold Separately)
(Optional)
1. If hole is not present drill a 1” (25.4mm) hole on countertop (refer to installation template on page 4).
2. Mount the spout onto the countertop or sink and hand tighten mounting bracket and spacer without damaging sensor cable.
3. Install batteries into battery pack and mount battery pack onto back wall using provided hardware
(battery pack must be installed within 15” (380mm) of spout).
Note: An optional 6 Volt AC power adapter (Part# AD05) can be purchased separately if electrical power is required.
4. Screw sanitizer bottle coupler onto threaded stem and hand tighten.
5. Fill up bottle with liquid or gel sanitizer.
6. Screw liquid sanitizer bottle onto sanitizer bottle coupler and hand tighten.
7. Connect sensor cable onto battery pack (you will hear pumps and sanitizer will purge for approximately 5 seconds).
8. Sanitizer dispenser is now ready for use.
Sanitizer Bottle Coupler
Threaded Stem
Low Battery Indicator
Low Sanitizer Indicator
Flashing BLUE LED
Flashing RED LED
Reset Button
www.amtcorporation.com
Attention:
Make sure sensor cable is passed
through the opening of the spacer
to avoid damage.
Page 2 of 4
Parts List
A
C
F
Reset Button
www.amtcorporation.com
H
D E
I
G
(Optional-Sold Separately)
ASD-600 ASD-600EL
A-1
Ref # Description Part #
A
C
D
E
F
G
HBattery Pack
800ml Sanitizer Bottle
Mounting Screws
Sanitizer Bottle Coupler
Mounting Bracket
Spacer
Spout
ASD-6BP
ASD-6SB
ASD-6MSC
ASD-6SBC
ASD-6MB
ASD-6SPA
ASD-6SPT
IAD05 6-Volt AC Power Adapter
(Optional)
J
AD05-2 6-Volt AC Power Adapter
w/Extension for 2 Devices
K
AD05-2-EXT Extension Only for AC
Power Adapter
A-1 EL Spout (6” Long)
ASD-6SPTEL
B
BSpout Filter Assembly
ASD-6FA
K
(Optional-Sold Separately)
J
(Optional-Sold Separately)
ASD-600 HY-GENIE™
AUTOMATIC LIQUID SANITIZER DISPENSER
INSTALLATION & OPERATION MANUAL

Page 3 of 4
www.amtcorporation.com
Reset Button
Reset Button
www.amtcorporation.com
Reset Button
1. Flashing Red LED Indicates Low Sanitizer 2. Unscrew Liquid Sanitizer Bottle 3. Refill Liquid Sanitizer Bottle
4. Re-install Liquid Sanitizer Bottle 5. Press and Hold Reset Button for 7 Seconds to
Prime New Sanitizer and Reset Flashing Red LED.
Refill Sanitizer When Sanitizer Level is Approx. 3/4” (20mm)
3/8”
(10mm)
www.amtcorporation.com
Reset Button
Flashing Red LED
3/4”
(20mm)
Max Filling Level is
Approx. 3/8” (10mm)
From Top of Bottle
Troubleshooting:
Flashing BLUE LED
Flashing RED LED
Problem Solution
Batteries are low/drained. Replace all 4 batteries (D-size).
Sanitizer is low or empty. Refill sanitizer bottle and press and hold reset button for 7 seconds to prime new sanitizer
and reset LED.
Sanitizer does not come out of spout Spout filter is dirty and won’t pump sanitizer through the spout. Clean or replace spout filter assembly.
Sanitizer Refill Instructions:
Sanitizer dispenses very weak Wrong sanitizer was used and pump is dirty. Refill sanitizer bottle with water and press and hold reset button for
7 seconds to prime water through the unit. This should be repeated until only water dispenses and sanitizer is
completely flushed out. Once unit is flushed out, refill sanitizer bottle with liquid sanitizer. Prime unit again until
sanitizer comes out.
™
ASD-600 HY-GENIE™
AUTOMATIC LIQUID SANITIZER DISPENSER
INSTALLATION & OPERATION MANUAL

Page 4 of 4
Advanced Modern Technologies Corporation
19800 Nordhoff Place, Chatsworth, CA 91311
Tel: [phone] Toll Free: [phone] Fax: [phone]
www.amtcorporation.com
™
Warranty
AMTC WARRANTS THE ASD-600 SANITIZER DISPENSER TO BE FREE OF DEFECTS IN MATERIAL AND
WORKMANSHIP FOR A PERIOD OF THREE (3) YEARS FROM DATE OF PURCHASE, WHEN PROPERLY
INSTALLED AND UNDER NORMAL USE AND SERVICE. THESE PROVISIONS DO NOT INCLUDE THE
BATTERIES SHIPPED WITH THE PRODUCT. A DEFECTIVE PRODUCT MAY BE RETURNED TO AMTC
OR ITS AUTHORIZED REPRESENTATIVES WITHIN THREE (3) YEARS FROM DATE OF PURCHASE
WITH THE PROPER INVOICE OF PURCHASE. AMTC, AT ITS DISCRETION, WILL REPLACE OR REPAIR
DEFECTIVE PRODUCT AT NO CHARGE. CLAIMS FOR LABOR, TRANSPORTATION, AND ANY OTHER
INCIDENTAL COSTS WILL NOT BE ALLOWED. AMTC WILL NOT BE RESPONSIBLE FOR ANY
CONSIDERABLE DAMAGES OF ANY KIND WHATSOEVER.
FOR TECHNICAL SUPPORT PLEASE CALL TOLL FREE 1-800-874-7822 OR VISIT OUR WEBSITE
AT WWW.AMTCORPORATION.COM.
MAKE SURE TO VISIT OUR WEBSITE PERIODICALLY FOR INFORMATION ON NEW PRODUCTS AND
TO DOWNLOAD ANY IMPORTANT PRODUCT DOCUMENTS THAT YOU MAY NEED IN THE FUTURE.
Installation Template for Model ASD-600 Spout (Not used for Model ASD-600EL)
3-3/4”
(95mm)
REF
Counter Top
Sink
Center Drill Point
1” (25.4mm) Hole
Spout Footprint
1-1/2” (38 mm)
(Scale 1:1)
Minimum To
Edge of Sink
Basin
Dispenser can be installed
on the left or right of the sink
Counter Top
Sink
REV. 03/20
™
ASD-600 HY-GENIE™
AUTOMATIC LIQUID SANITIZER DISPENSER
INSTALLATION & OPERATION MANUAL