Analog Devices Blackfin A-V EZ-Extender User manual

a
Blackfin®A-V EZ-Extender®
Manual
Revision 2.1, July 2012
Part Number
82-000870-01
Analog Devices, Inc.
One Technology Way
Norwood, Mass. 02062-9106

Copyright Information
© 2012 Analog Devices, Inc., ALL RIGHTS RESERVED. This docu-
ment may not be reproduced in any form without prior, express written
consent from Analog Devices, Inc.
Printed in the USA.
Disclaimer
Analog Devices, Inc. reserves the right to change this product without
prior notice. Information furnished by Analog Devices is believed to be
accurate and reliable. However, no responsibility is assumed by Analog
Devices for its use; nor for any infringement of patents or other rights of
third parties which may result from its use. No license is granted by impli-
cation or otherwise under the patent rights of Analog Devices, Inc.
Trademark and Service Mark Notice
The Analog Devices logo, Blackfin, CrossCore, EngineerZone,
EZ-Extender, EZ-KIT Lite, and VisualDSP++ are registered trademarks of
Analog Devices, Inc.
All other brand and product names are trademarks or service marks of
their respective owners.

Regulatory Compliance
The Blackfin A-V EZ-Extender is designed to be used solely in a labora-
tory environment. The board is not intended for use as a consumer end
product or as a portion of a consumer end product. The board is an open
system design which does not include a shielded enclosure and therefore
may cause interference to other electrical devices in close proximity. This
board should not be used in or near any medical equipment or RF devices.
The Blackfin A-V EZ-Extender has been certified to comply with the
essential requirements of the European EMC directive 2004/108/EC and
therefore carries the “CE” mark.
The Blackfin A-V EZ-Extender has been appended to Analog Devices,
Inc. EMC Technical File (EMC TF) referenced DSPTOOLS1, issue 2
dated June 4, 2008 and was declared CE compliant by an appointed Noti-
fied Body (No.0673) as listed below.
Notified Body Statement of Compliance: Z600ANA1.023 dated
December 2, 2004.
Issued by: Technology International (Europe) Limited
56 Shrivenham Hundred Business Park
Shrivenham, Swindon, SN6 8TY, UK
The Blackfin A-V EZ-Extender contains ESD (electrostatic discharge) sen-
sitive devices. Electrostatic charges readily accumulate on the human body
and equipment and can discharge without detection. Permanent damage
may occur on devices subjected to high-energy discharges. Proper ESD pre-
cautions are recommended to avoid performance degradation or loss of
functionality. Store unused extender boards in the protective shipping pack-
age.

Blackfin A-V EZ-Extender Manual v
CONTENTS
PREFACE
Product Overview .......................................................................... x
Purpose of This Manual ................................................................ xi
Intended Audience ....................................................................... xii
Manual Contents ......................................................................... xii
What’s New in This Manual ........................................................ xiii
Technical Support ....................................................................... xiii
Supported Processors .................................................................... xiv
Product Information .................................................................... xiv
Analog Devices Web Site ........................................................ xiv
EngineerZone .......................................................................... xv
Related Documents ...................................................................... xvi
A-V EZ-EXTENDER INTERFACES
A-V EZ-Extender Setup ................................................................ 1-2
Analog Audio Interface .................................................................. 1-3
Analog Video Interface .................................................................. 1-4
Camera Module Interfaces ............................................................. 1-4

Contents
vi Blackfin A-V EZ-Extender Manual
Flat Panel Display Interface ........................................................... 1-6
Example Programs ........................................................................ 1-7
A-V EZ-EXTENDER HARDWARE REFERENCE
System Architecture ...................................................................... 2-2
Jumpers ........................................................................................ 2-7
Video Test Loopback Jumpers (JP1.1/2, JP1.3/4, JP1.5/6) ....... 2-8
Connector Voltage Selection Jumper (JP2) ............................... 2-8
TWI Source Selection Jumpers (JP3.3/5/7, JP3.4/6/8) ............. 2-8
PDWN Connect Jumper (JP3.9/10) ........................................ 2-9
Decoder HSYNC Disconnect Jumper (JP3.11/12) ................... 2-9
Decoder VSYNC Connect Jumper (JP3.13/14) ........................ 2-9
Encoder HREF Connect Jumper (JP3.15/16) ........................ 2-10
Encoder VSYNC Connect Jumper (JP3.17/18) ...................... 2-10
Decoder Output Enable Jumper (JP3.19/20) ......................... 2-10
SNAPSHOT_FODD Disconnect Jumper (JP3.21/22) ........... 2-10
PPI Clock Setup Jumpers
(JP4.1/2, JP4.3/4, JP4.5/6, JP4.7/8) ................................... 2-11
PPI0 D8–15 Enable Jumper (JP5.1/2) ................................... 2-11
VID_OUT Data Bus Control Jumpers (JP5.3/4, JP5.5/6) ...... 2-12
PPI0_SYNC1 Direction Setup Jumper (JP6.1/3/5) ................ 2-12
PPI0_SYNC2 Direction Setup Jumper (JP6.2/4/6) ................ 2-13
I2S Enable Jumper (JP7.1/2) ................................................. 2-13
SPORT Data Connect Jumpers (JP7.3/4, JP7.5/6) ................ 2-13

Blackfin A-V EZ-Extender Manual vii
Contents
VID_OUT Bus SYNC Source Select Jumpers
(JP8.1/3/5, JP8.2/4/6) ........................................................ 2-14
VID_OUT Bus SYNC Enable Jumper (JP8.7/8) .................... 2-14
AV_RESET Source Jumper (JP9.1/3/5) .................................. 2-14
PPI0_D Direction Setup Jumper (JP9.2/4/6) ......................... 2-15
Audio Loopback Jumpers (JP10.1/2, JP10.3/4) ...................... 2-15
A-V EZ-EXTENDER BILL OF MATERIALS
A-V EZ-EXTENDER SCHEMATIC
INDEX

Contents
viii Blackfin A-V EZ-Extender Manual

Blackfin A-V EZ-Extender Manual ix
PREFACE
Thank you for purchasing the Blackfin®A-V EZ-Extender®, Analog
Devices, Inc. daughter board to the EZ-KIT Lite®evaluation system for
the ADSP-BF533, ADSP-BF537, and ADSP-BF561 Blackfin processors.
Blackfin processors are embedded processors that support a Media
Instruction Set Computing (MISC) architecture. This architecture is the
natural merging of RISC, media functions, and digital signal processing
characteristics towards delivering signal processing performance in
a microprocessor-like environment.
EZ-KIT Lites and A-V EZ-Extenders are designed to be used in conjunc-
tion with the CrossCore®Embedded Studio (CCES) and VisualDSP++®
software development environments. The development environment facil-
itates advanced application code development and debug, such as:
• Create, compile, assemble, and link application programs written
in C++, C, and A-V EZ-Extender assembly
• Load, run, step, halt, and set breakpoints in application programs
• Read and write data and program memory
• Read and write core and peripheral registers
• Plot memory
To learn more about Analog Devices development software, go to
http://www.analog.com/processors/tools.

Product Overview
x Blackfin A-V EZ-Extender Manual
Product Overview
The Blackfin A-V EZ-Extender is a separately sold daughter board that
plugs onto the expansion interface of the ADSP-BF533, ADSP-BF537, or
ADSP-BF561 EZ-KIT Lite evaluation system. The extender board aids
the design and prototyping phases of the ADSP-BF533, ADSP-BF537, or
ADSP-BF561 processor targeted applications.
The board extends the evaluation system capabilities by providing a con-
nection to a video decoder; video encoder; multiple camera evaluation
boards; flat panel display; and 3-stereo input channel, 2-stereo output
channel audio codec.
Please visit www.analog.com/EX1-AV for additional information, including
CCES support.
The board features:
• Analog audio interface
• AD1836A Analog Devices 96 kHz audio codec
• Five 3.5 mm audio jacks, stacked in one connector
• Analog video interface
• ADV7183B video decoder with three input RCA phono
jacks
• ADV7179 video encoder with three output RCA phono
jacks
• OmniVision camera module interface
• Connection to OmniVision camera evaluation modules;
for example, OV6630AA (this part is no longer available)
• 32-pin, right-angle, 0.1 in. spacing, female socket