Analytic Systems IVS1000 User manual

Installation &
Operation Manual
8128 River Way, Delta B.C. V4G 1K5 Canada T. 604.946.9981 F. 604.946.9983 TF. 1.800.668.3884 (US/CANADA)
www.analyticsystems.com
IVS1000
Pure Sinewave Inverter

2
Copyright (2005-2013) Analytic Systems Ware (1993) Ltd.

3
IMPORTANT & SAFETY INSTRUCTIONS
1) SAVE THESE INSTRUCTIONS — is manual contains important safety and operating
instructions for inverter.
2) Do not expose inverter to rain or snow.
3) Use of an attachment not recommended or sold by the inverter manufacturer may result in a
risk of re, electric shock, or injury to persons.
4) Do not disassemble inverter; take it to a qualied serviceman when service or repair is re-
quired. Incorrect reassembly may result in a risk of electric shock or re.
5) To reduce risk of electric shock, unplug inverter from outlet before attempting any mainte-
nance or cleaning. Turning o controls will not reduce this risk.
6) Never place inverter directly above battery; gases from battery will corrode and damage marine
inverter.
7) Never allow battery acid to drip on inverter when reading gravity or lling battery.
GROUNDING AND AC POWER CORD CONNECTION INSTRUCTIONS — Inverters should be
grounded to reduce risk of electric shock. Inverter is equipped with electric receptacles capable of accepting
an equipment-grounding conductor and a grounding plug.
DANGER — Never alter AC cord or plug provided — if it will not t outlet, have proper cord installed by a
qualied electrician. Improper connection can result in a risk of an electric shock.
Analytic Systems does not recommend the use of the IVS2500 Series Inverters in life support applications
where failure or malfunction of this product can be reasonably expected to cause failure of the life support
device or to signicantly aect its safety or eectiveness. Analytic Systems does not recommend the use of
any of its products in direct patient care.
Examples of devices considered to be life support devices are neonatal oxygen analyzers, nerve stimulators
(whether used for anesthesia, pain relief, or other purposes), autotransfusion devices, blood pumps, debril-
lators, arrhythmia detectors and alarms, pacemakers, hemodialysis systems, peritoneal dialysis systems,
neonatal ventilator incubators, ventilators for both adults and infants, anesthesia ventilators, and infusion
pumps as well as any other devices designated as “critical” by the U.S. FDA.

4
System Description
e IVS1000 inverter series was designed electrically and mechanically to achieve optimal ruggedness
required for industrial, telecommunications, military and airborne applications.
Electrical Connections
e input can be grounded either on the positive or negative, or may be le oating. e output is normally
grounded, although it can be oating if required for specic applications.
Mount the unit as close to the battery as possible to avoid voltage drop and losses on the wires. e input
connections are via a 3-pole terminal block. GND, POS and NEG are clearly labeled. Although the unit
is reverse polarity protected, ensure that input is connected correctly. (On some models, the internal fuse
blows when reverse polarity occurs).
If operating the inverter from a power supply (instead of a battery), ensure that this source is capable of sup-
plying a signicantly higher current than is actually required. It is preferable to turn on the inverter rst, and
connect the load aer the inverter is already running.
Input Wire Sizes
Input wire size is crucial for maximum eciency and safety. For best results, the shortest length and largest
gauge wire should be used. Marine type battery terminals are recommended for attaching connectors to the
battery. Keep all connectors clean and free of corrosion. Refer to the following table for proper sizing. e
following values are to be used for guidelines only! e actual application must be considered for selecting
wire gauge, insulation, as well as EMI considerations for wire routing and shielding where necessary. For
longer wire lengths, larger gauge wire may be needed to minimize line losses.
RECOMMENDED INPUT WIRE SIZES
DISTANCE FROM BATTERY
MODEL
5’ 10’ 15’ 20’
IVS1000-24V to 36V AWG 4 AWG 2 AWG 0 AWG 00
IVS1000-48V AWG 8 AWG 8 AWG 6 AWG 6
IVS1000-125V AWG 10 AWG 10 AWG 10 AWG 10
IVS1000-250V AWG12 AWG12 AWG12 AWG12

5
Location
e unit should be mounted securely to a at surface with a minimum of one-inch clearance to provide
ample airow and to achieve maximum continuous power. Cooling is enhanced if the unit is installed on a
metal surface to allow for additional conduction cooling.
Electronic Protection
e inverter has a number of protection circuits designed to provide full electronic protection:
Grounding - e input can be either positively or negatively grounded, or may be le oating. e output is
normally grounded, although it can be le oating if required.
ermal shutdown - In the event of overheating due to high ambient temperature, blocked air ow or over-
load conditions, the internal thermal protection circuit will shut the unit down. Operation will automatically
resume when the temperature reaches the specied operating level.
Overload and short-circuit protection - In case of an overload or short circuit, the inverter will go into “hic-
cup” mode. is means that the unit will automatically shut down and will periodically test whether or not
the overload condition still exists.
Reversed Input Polarity Protection – e IVS1000 inverter series has sophisticated protection to ensure that
no damage occurs whilst reverse polarizing the input. (On some models, the internal input fuse may blow
when reverse polarity occurs).
Input and output ltering - All IVS1000 series inverters have a double stage input lter to restrict EMI emis-
sions. Filtering also provides immunity against voltage spikes and other disturbances on the input power
line. e inverters meet FCC 20780 Class B and EN 55022 Class B conducted emission requirements.
On/o Switch
e IVS1000 inverter series has an on/o switch, which disables the inverter’s control circuit. Turning the
switch to the ‘OFF’ position cuts the power to the AC output. A minimal current drain will continue on
the DC input side. Always disconnect the inverter when not in use for an extended period of time to avoid
draining the battery and to prolong battery life.
Operating
Before plugging any appliance into the inverter, please refer to its power requirements. Power requirements
are indicated in watts (W), volt-amps (VA) or amps (A). Ensure that the rating does not exceed the inverter’s
capacity.
Safety Considerations
WARNING: e IVS1000 inverter series generate 115VAC power – the same voltage coming out of a
standard wall outlet. is voltage can be hazardous and has to be treated with the same caution as a regular
electrical outlet.
As with any other electrical equipment, the inverter unit must be protected from water and moisture at all
times.

6
Specications
Designed and manufactured by: ANALYTIC SYSTEMS WARE (1993) LTD.
8128 River Way, Delta, B.C., V4G 1K5, Canada
phone [phone] fax [phone] toll free 800-668-3884 US/Canada
email: [e-mail] web site: www.analyticsystems.com Revised Mar 2004
* Specications subjects to change without notice.
INPUT
Input Voltage: 24Vdc 36Vdc 48Vdc 125Vdc 250Vdc
Input Protection: Inrush current limiting, thermal fuse & reverse polarity
Input Isolation:
500 Vdc input to output& input to chassis for <60Vdc input
1400 Vdc input to output& input to chassis for ³60Vdc input
500Vdc output to chassis – all inverters
OUTPUT
Output Voltage / Current: 115 VAC / 60 Hz / 8.7 Amp continuous (1000VA)
Wave Form: Sinusoidal
Total Harmonic Distortion: Better than 5% at full load
Line Regulation: Maximum 0.5%
Load Regulation: Maximum ±6% from 10% load to full load
Output Noise: High frequency ripple is better than 500 mVrms (20 MHz BW)
GENERAL
Temperature Dri: 0.05% per º C over operating temperature range
Operating Temp. Range: 0 º C to +50 º C for full specication with internal fan
Humidity: 5 - 95 % non-condensing
Output Protection: Current limiting with short-circuit protection. ermal shutdown with
automatic recovery in case of continuous overload or insucient airow
Output Overload Protec-
tion: Hiccup at 1200 W
Output Over-voltage
Protection: By internal supply voltage limiting at 120% V out, nominal level
Load Crest Factor: Maximum 2.5 at 90% load
RFI Suppression: Meets requirements of FCC 20780 Class B and EN55022 Class B conducted
emissions as a minimum
Eciency: Minimum 80% at full load
Cooling: By internal fan
Input Connection: Screw-type terminal block
Output Connection: Standard AC Receptacle (North American Type)
Package Size / Weight: 5.3 x 7.5 x 15.5 Enclosed case, 13 pounds ( 6 kg )

7
1. e equipment manufactured for Analytic Systems Ware (1993) Ltd. (the “Warrantor”) is warranted to
be free from defects in workmanship and materials under normal use and service.
2. is warranty is in eect for: 2 Years from date of Purchase.
3. In case any part of the equipment proves to be defective, the Purchaser should do the following:
a. Prepare a written statement of the nature of the defect to the best of the Purchasers knowledge,
and include the date of purchase, the place of purchase, and the Purchasers name, address and
telephone number.
b. Call Analytic Systems at 800-668-3884 or 604-946-9981 and request a return material authori-
zation number (RMA).
c. Return the defective part or unit along with the statement at the Purchasers expense to the
Warrantor; Analytic Systems Ware (1993) Ltd., 8128 River Way, Delta, B.C., V4G 1K5, Canada.
4. If upon the Warrantor’s examination the defect proves to be the result of defective material or work-
manship, the equipment will be repaired or replaced at the Warrantor’s option without charge, and
returned to the Purchaser at the Warrantor’s expense by the most economical means. Requests for a
dierent method of return or special handling will incur additional charges and are the responsibility of
the Purchaser.
5. Analytic Systems reserves the right to void the warranty if:
a. Identication marks or serial numbers are removed or altered in any way.
b. Our invoice is unpaid.
c. e defect is the result of misuse, neglect, improper installation, environmental conditions,
non-authorized repair, alteration or accident.
6. No refund of the purchase price will be granted to the Purchaser, unless the Warrantor is unable to
remedy the defect aer having a reasonable number of opportunities to do so.
7. Only the Warrantor shall perform warranty service. Any attempt to remedy the defect by anyone else
shall render this warranty void.
8. ere shall be no warranty for defects or damages caused by faulty installation or hook-up, abuse or
misuse of the equipment including exposure to excessive heat, salt or fresh water spray, or water im-
mersion except for equipment specically stated to be waterproof.
9. No other express warranty is hereby given and there are no warranties that extend beyond those de-
scribed herein. is warranty is expressly in lieu of any other expressed or implied warranties, includ-
ing any implied warranty of merchantability, tness for the ordinary purposes for which such goods
are used, or tness for a particular purpose, or any other obligations on the part of the Warrantor or its
employees and representatives.
Limited Warranty

10. ere shall be no responsibility or liability whatsoever on the part of the Warrantor or its employees
and representatives for injury to any person or persons, or damage to property, or loss of income or
prot, or any other consequential or resulting damage which may be claimed to have been incurred
through the use or sale of the equipment, including any possible failure of malfunction of the equip-
ment, or part thereof.
11. e Warrantor assumes no liability for incidental or consequential damages of any kind.
8128 River Way, Delta B.C. V4G 1K5 Canada T. 604.946.9981 F. 604.946.9983 TF. 1.800.668.3884 (US/CANADA)
www.analyticsystems.com