ANATEL L5B83G User manual

User Manual
Model: L5B83G
This product is a Bluetooth Low Energy technology enabled Remote Control for use with a
paired Media Player.
Operating Frequency Range: 2402 – 2480 MHz
Maximum Effective Isotropic Radiated Power (EIRP): 10dBm
WHAT’S IN THE BOX
• Marketing Name: Wireless Remote, Model L5B83G
• 2xAAA Batteries
Setting up the device
- Insert the batteries and install the compartment cover
- Pair the device with the host. Choose the applicable pairing instructions from options A or
B below:
A. This is a replacement remote control:
1. Restart your Media Player / TV USB Stick by disconnection from and then
reconnection to the AC power. After the TV home screen displays your new remote
it is ready for pairing.
2. Press and hold the Home button on the new remote for at least 10 seconds. The new
remote should automatically pair with your TV USB stick. You will see an on-screen
message when it has successfully paired.
B. This is an additional remote control:
1. On your new remote, press and hold the Home button for 120 seconds to enter
discoverable mode.
2. You must use your existing remote for the following steps.
a. Press the Home button.
b. Navigate to the Settings location at the top of the Media Player TV screen. Select
Controllers and Bluetooth Devices > TV Remotes > Add New Remote.
The Media Player application will search for discoverable remotes and display
them in a list.
c. Select the new remote. You will see an on-screen message when it has been
successfully paired.
Use your Voice Search
- Hold down voice search button and speak

Safety and Compliance Information
For safety, compliance, recycling, and other important information regarding your Device,
please refer to the Legal & Compliance section in the User Manual.
Caution: risk of explosion if the batteries are replaced by an incorrect type. Dispose of used
batteries according to the instructions.
Using Your Device Around Other Electronic Devices
The Device, uses, and can radiate radio frequency (RF) energy and, if not used in accordance
with its instructions, may cause interference to radio communications and electronic
equipment. External RF signals may affect improperly installed or inadequately shielded
electronic operating systems, entertainment systems, and personal medical devices.
While most modern electronic equipment is shielded from external RF signals, if in doubt, check
with the manufacturer. For personal medical devices (such as pacemakers and hearing aids),
consult with your physician or the manufacturer to determine if they are adequately shielded
from external RF signals.
There are some places where RF signals could constitute a hazard, such as health care facilities,
and construction sites. If you are not sure, look around for signs indicating that two-way radios
or mobile phones should be turned off.
FCC – regulatory user information
This equipment complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Modifications of the equipment which are not expressly approved by the party responsible for
it’s compliance could void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.

Innovation, Science and Economic Development Canada (ISED) – regulatory user information
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation,
Science and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the
following two conditions:
1.This device may not cause interference; and
2.This device must accept any interference, including interference that may cause undesired
operation of the device.
Conformité Innovation Sciences et Développement Économique Canada (ISDE)
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux
CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils
radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes:
1.l’appareil ne doit pas produire de brouillage; et
2.l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionnement.
EU Declaration of Conformity:
Hereby, Amazon.com Services LLC., declares that the radio equipment type L5B83G is in
compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet
address: www.amazon.com/device_eu_compliance.
Brazil Compliance Warning Statement
HHHHH-AA-FFFFF
Requirements for products with Bluetooth/wifi:
Este equipamento não tem direito à proteção contra interferência prejudicial e não pode causar
interferência em sistemas devidamente autorizados.
Mexico Compliance Warning Statement
La operación de este equipo está sujeta a las siguientes dos condiciones: (1) es posible que este

equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debe
aceptar cualquier interferencia, incluyendo la que pueda causar su operación no deseada.