Anelto OnTheGo LiTE User manual

OnTheGo LiTE User Guide
Getting to Know Your OnTheGo LiTE:
1) Lanyard Loop
2) LED
3) Speaker
4) HELP Button (Emergency Button)
5) Microphone
6) Charging Cable (Not Shown)
7) Lanyard (Not Shown)
Charging Your Device:
Whenever you put the plugged-in charging cable near the charging port on the back of the device, it should latch into
place and the device will automatically power on. The LED will turn solid red and the device will announce, “Your
device is now charging.” Note: If you have allowed the battery to completely drain, it may take a few minutes for the
device to power on.
When the device has adequate battery charge and is also connected to the cellular network, it will announce, “Your
device is now ready.” This indicates that your device is ready to make an emergency call. However, you should leave
your device on the charging cable until the LED is green, indicating that your device has completed charging.
A complete charge will take approximately 2-3 hours. When fully charged your device should work for up to three
days before needing to be recharged.
LED
Announcement
What this means
What you should do
Solid Red
“Your device is now
charging.”
Device is connected to the
charger
Leave on charger until
battery is charged and the
LED is green
Blinking Red
“Your device battery is
low. For your protection,
please place your device
on the charger now.”
Your battery is critically
low
Place device on charger as
soon as possible
Blinking Green
Your device has adequate
charge and is looking for
cellular connection
Wait. If this continues
move to another location
with better cell coverage
Solid Green
“Your device is now
ready.”
Your device is ready to
make a call
Press the button if you
wish to make a call
Placing an Emergency Call:
HELP Button Action
Announcement
What this means
What you should do
To place a call, press and
hold for 1 second or
more
Device will BEEP and
announce “Placing an
emergency call now. To
cancel the call please press
and hold the HELP button
for two seconds now.”
Device will make a call
Release the button
To cancel a call, press
and hold for 2 seconds
after the “Dialing the
emergency response
center….”
announcement
“Your call has been
cancelled.”
The call has been cancelled
Release the button
#1
#2
#3
#4
#5

!
HELP Button Results
Announcement
What this means
What you should do
If you do not cancel a
call, the call will be
placed
You will hear the phone
ringing; the Call Center will
answer and help you
Talk to the Call Center
If the call cannot be
placed due to poor cell
connection or other
issues
“Call failed.”
You must push the button
again to attempt to place
the call
You may need to move to
an area where there is a
better cellular connection
Turning your device OFF:
Your device is designed to always be ON. The only time you should ever need to turn it OFF is if you are taking your
device on an airplane. In that case please follow these instructions.
HELP Button Action
Announcement
What this means
What you should do
To turn your device off,
press and quickly release
your button three times
"Device is powering off.
Please confirm by pressing
and holding the HELP
button now".
Device is about to power
off
Either confirm or not
To confirm, press and
release the button once
"Powering off now.
Goodbye."
Device is powering off
To leave device on, do
not press the button
Device will remain on
Turning your device ON again:
To turn your device ON again after it has been powered OFF, either place it on the charger or press and hold the HELP
button for one second.
Welcome Announcement:
The first time you turn on your system it may announce, “Hello, it is time to test your system to make sure it is
working properly. Please press and hold the HELP button for one second now.” Please make this test call when
requested.
Fall Detection (if enabled):
• Fall Detect can be enabled and/or disabled remotely by your provider.
• In order for Fall Detect to work properly when enabled, the device must be worn on a lanyard around your neck
and rest high on your torso near your chest plate.
• Fall Detect may not detect 100% of falls; an Emergency Call may need to be made by pushing the HELP button.
• Fall Detection Call (if enabled): “A fall has been detected. Placing an emergency call now. To cancel the Fall
Detect event, press and hold the emergency button for two seconds.”
• To cancel a call made due to a Fall Detect event, after you hear the announcement, press the button for two
seconds.
• Fall Detect may decrease available time between battery charges.
Important Tips and Reminders:
• Your device requires adequate battery charge and cellular signal to make an emergency call.
• Your device uses GPS technology to identify your location. In good conditions the product should provide a
location that is accurate within 30 feet or less. However, performance of GPS can be affected by a wide range of
factors including obstructions, metal objects in the vicinity, structures that block the signal from satellites,
weather, and other factors.
• Your device is splash proof and can be worn in the shower.
• Please test your system at least once a month.
• Your device uses the cellular network to communicate. The device’s location, network provider service
availability, and other issues may disrupt communications.

Warnings:
• Pendant lanyards are designed to breakaway under certain conditions; however, any cord worn around the neck
can pose a risk of strangulation, including the possibility of serious injury or death.
• The back of this device and the charging cable both contain strong magnets. Magnets with a strong
magnetic field may cause permanent damage to health devices susceptible to magnetic fields, credit cards,
computer hard drives, watches, TVs, data storage media and other electronic devices. These strong magnets
should be kept a minimum of three inches away from health devices susceptible to magnetic fields, i.e.
pacemaker, defibrillator, etc. Please check with your physician prior to using this device if you have any
concerns.
• Our products are tested, as are other cellular and wireless communications products licensed in the United
States. Individuals with pacemakers should review their pacemaker materials regarding interaction with cell
phones and take the same precautions the materials recommend for this device.
Regulatory Compliance: FCC
The user’s manual or instruction manual for an intentional or unintentional radiator shall caution the user that
changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate the equipment.
This device complies with Part 15 of the United States FCC regulations. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
For a Class B digital device or peripheral, the instructions furnished the user shall include the following or similar
statement, placed in a prominent location in the text of the manual:
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This equipment has been tested and found to comply with the limits pursuant to Part 15 Subpart B, Part 22, and Part
24 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in an
appropriate installation. This equipment generates, uses, and can radiate radio frequency energy and, if not used in
accordance with instructions, can cause harmful radiation to radio communication. However, there is no guarantee
that interference will not occur in a particular installation.
Regulatory Compliance: RF Exposure
Your device is a radio transmitter and receiver. It is designed and manufactured not to exceed the emissions limits for
exposure to radio frequency (RF) energy set by the Federal Communications Commission (FCC) of the U.S.
Government. These limits are part of comprehensive guidelines and establish permitted levels of RF energy for the
general population. These guidelines are based on the safety standards previously set by the U.S. and international
standards bodies. The standards include a substantial safety margin designed to assure the safety of all persons,
regardless of age and health.
The exposure standard for wireless RF devices, such as the device, employs a unit of measurement known as the
Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg. SAR values at or below that limit are
considered safe for the general public.
Before a wireless RF device is made available for sale to the Public, it must be tested and certified to the FCC that it
does not exceed the SAR limits established by the FCC. Tests for SAR are conducted using the positions and locations
(e.g., at the ear or worn on the body) as required by the FCC for each device model.
The device has been tested and meets the FCC RF exposure guidelines when used against the body under normal
usage conditions.
To comply with FCC RF exposure requirements, a minimum separation distance of 10mm must be maintained.