Animo M series User manual

M-LINE M100
M102
MT100
MT100v
gebruiksaanwijzing
user manual
betriebsanleitung
mode d'emploi

2015/02 Rev. 4.0
M-LINE
M100 fig. 1 / Abb. 1
M102 fig. 2 / Abb. 2
620
460
205
380
420
34
38
E
E
620
460
420
380
420
246
155
246
38
370
E
E

2015/02 Rev. 4.0
M-LINE
8
6
5
4
3
2
9
7
10
1
7
14 13
12
6
5
9
1
7
5
5.1 5.2 5.3
13
14
11
12
11
Animo
........................
......................../ .........................
MADE IN HOLLAND
........................V 50-60Hz ..............W
Animo
........................
........................ / ...........................
MADE IN HOLLAND
........................V 50-60Hz ...............W

2015/02 Rev. 4.0
M-LINE
MT100 fig. 3/Abb. 3
MT100v fig. 4/Abb. 4
595
205
380
420
50
50
55
E
E
min 540 / max 650
205
380
420
75
55
E
E
min 265 / max 375

2015/02 Rev. 4.0
M-LINE
Nederlands ..................................... 1
English ........................................... 20
Deutsch .......................................... 39
Français ......................................... 58

2015/02 Rev. 4.0
M-LINE
20 GB
TABLE OF CONTENTS
Preface ..................................................... 21
Introduction .................................................... 22
Safety instructions and danger warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Safeguards .................................................... 24
Appliances and the environment .................................... 26
1. General ..................................................... 26
1.1 A quick look at the appliance .................................... 26
1.1.1 Most important parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
1.1.2 Controlpanel ......................................... 26
2. Technicaldetails ................................................ 27
3. Installation ..................................................... 27
3.1 Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
3.2 Installation ................................................. 28
3.2.1 Preparation for positioning the appliance .................... 28
3.2.2 Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
3.2.3 Water drainage ........................................ 28
3.2.4 Firsttimeuse ......................................... 28
3.2.5 Height setting model MT200v ............................. 29
3.2.6 Setting the descale indicator .............................. 30
3.2.7 Resetting the descale indicator light . . . . . . . . . . . . . . . . . . . . . . . 30
4. Daily use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ... 31
4.1 Dripstop .................................................. 31
4.2 Coffeequantity ............................................. 31
4.3 Makingcoffee .............................................. 32
4.4 Makingtea ................................................. 32
4.5 Termination of the brewing process? . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
5. Settings ..................................................... 33
5.1 Setting of the prewet function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
6. Maintenance .................................................... 34
6.1 Cleaning of the appliance and accessories . . . . . . . . . . . . . . . . . . . . . . . . 34
6.1.1 Removing coffee deposits from glass jug and filter ............ 34
6.1.2 Removing coffee deposits from thermos jug . . . . . . . . . . . . . . . . . 34
6.2 Descaling .................................................. 35
6.2.1 Switching-off the descaling indicator light . . . . . . . . . . . . . . . . . . . 35
7. Troubleshooting ................................................. 36
8. Ordering consumer articles and accessories . . . . . . . . . . . . . . . . . . . . . . . . . . 38

2015/02 Rev. 4.0
M-LINE
21
GB
© 2009 Animo®
All rights reserved.
No part of this document may be reproduced and/or publicized by means of printing, microfilm, electronic or any
other means whatsoever without the prior written permission of the manufacturer. This also applies to the accompany-
ing drawings and/or diagrams.
Animo reserves the right to change parts at any time without giving prior or direct notification to the customer. The
contents of this manual can also be changed without prior notification.
This manual covers the standard model of the appliance. Animo can therefore not be held liable for any losses aris-
ing from the fact that the specifications of the appliance supplied to you deviate from the standard model. Please
contact your supplier’s service department for information concerning adjustment, maintenance or repairs not cov-
ered by this manual.
Although this manual was produced with the greatest possible care, the manufacturer is unable to accept liability
For errors in this document or their consequences.
You are advised to carefully read the instructions in this document: they contain important information
about safety when installing, using and maintaining the appliance. Keep this document in a safe place so
that you can consult it when necessary.
Preface
Purpose of this document
Thisdocumentservesasamanualthatenablesqualiedpersonneltosafelyinstall,
program and maintain the coffee maker.
- ‘Qualiedpersonnel’aredenedaspeoplethatcanprogramtheappliance,perform
maintenance on it and repair minor faults.
All of the chapters and paragraphs are numbered. The various illustrations to which the
text refers are given in the fold-out sheets or at the back of this booklet or under the par-
ticular subjects.
Icons and symbols
NOTICE
General instruction for: IMPORTANT, NOTE or REMARK.
CAUTION !
Warning of possible damage to the appliance, the surroundings or the
environment.
WARNING
Warning of possible serious damage to the appliance or physical injury.
WARNING
Warning of electricity hazard.

2015/02 Rev. 4.0
M-LINE
22 GB
Introduction
Congratulations on your purchase and welcome to Animo! To fully benefit from the sup-
port that Animo offers, register your product at www.animo.eu/warranty
Models
This manual covers the following coffee makers:
Double model height-adjustable
Purpose of the appliance
The sole purpose of this appliance is to make coffee and/or tea.
The use of the appliance for other purposes is not permitted and may be hazardous.
The manufacturer cannot be held liable for losses caused by using the appliance for pur-
poses other than those indicated here or by incorrect use.
Service and technical support
Please contact your dealer for information not given in this document regarding specific
adjustment, maintenance and repairs. Before contacting your dealer you should note the
following appliance details, marked with a #. You will find these details on the type plate
attached to your appliance (11).
A - Type #
B - Article number #
C - Machine number #
D - Supply voltage
E - Frequency
F - Output
Guarantee conditions
The guarantee conditions applicable to this appliance form an integral part of the general
terms of delivery.
Directives
This appliance meets the requirements of the EMC Directive 89/336/EEC, and the Low
Voltage Directive 72/23/EEC.
........................
........................ / ...........................
........................ V 50-60Hz ....................W
A
B
F
D
E
C
MADE IN HOLLAND
ANIMO
M100 M102 MT100 MT100v
1,2
2,4
2,5
1
2
2,2
1,85 2,1 / 2,2 2,4 Lt
r
ANIMO

2015/02 Rev. 4.0
M-LINE
23
GB
Safety instructions and danger warnings
This appliance meets the mandatory safety regulations. Inexpert use can result in per-
sonal injury and material damage. The following warnings and safety instructions must
be observed before using the coffee maker.
Instructions for use
Read these instructions for use carefully, before using this appliance. This will protect
your safety and prevent damage being caused to the appliance. Perform the various
actions in the order given. Always keep this manual close by the appliance.
Installation
• Placetheapplianceatbuffetheightandonafirm,levelbase,insuchawaythatit
can be connected to the power supply.
• Connecttheappliancetoanearthedwallsocket.
• Positiontheapplianceinsuchawaythatnodamagecanbecausedifitleaks.
• Donottilttheappliance,alwayspositionandmovetheapplianceupright.
• Thecoffeemakerisfittedwithanoverflowdevicethatdischargesatthebottomof
the appliance - take this into account when positioning the appliance.
• Wateralwaysremainsintheheatingsystem:forthisreasontheappliancemustnot
be placed in an area where the temperature can fall below freezing point.
• Wheninstallingtheappliance,alwaysobservethelocalrulesanduseapproved
materials and parts.
• The‘Installation’chaptermustagainbefollowedwhenrepositioningtheappliance.
Usage
• Inspecttheappliancebeforeusingitandcheckitfordamage.
• Neversubmergeorspraytheappliance.
• Donotpressthebuttonswithasharpobject.
• Protectthecontrolsagainstdirtandgrease.
• Itisadvisabletotaketheplugoutofthesocketandclosethewatertapifthe
appliance is not going to be used for longer periods of time.
Maintenance and troubleshooting
• Observethedescalingintervalsindicatedbythedescalingindicatorlight.
Overdue maintenance to the heating system can result in high repair costs and
annulment of the guarantee.
• Alwaysfollowthemanufacturer’sinstructionswhenusingthedescalingagent.
• Donotleavetheapplianceunattendedwhenmaintenanceisbeingperformed.
• Whendescalingtheappliance,itisadvisabletowearsafetyglassesandprotective
gloves.
• Never clean the hot plates (if present) with an abrasive or sharp object. This way
scratches on the teflon surface will be prevented.
• Flushtheapplianceatleasttwiceafterdescalingit.
• Washyourhandsthoroughlyafterdescalingtheappliance.
• Alwayshaverepairscarriedoutbyaqualifiedserviceengineer.

2015/02 Rev. 4.0
M-LINE
24 GB
• Theplugmustbetakenoutofthesocketiftheappliancehastobeopenedfor
cleaning or repairs.
The manufacturer cannot be held liable for losses caused as a result of failure to observe
these safety instructions.
Safeguards
The appliance is fitted with the following safeguards:
Dry-boil protection (14)
This appliance is equipped with a dry-boil protection. This protection triggers if the
heating element overheats owing to a fault. Once the fault has been resolved, the dry-
boil protection can be reset at the back of the appliance. The most common cause of the
dry-boil protection being triggered is not descaling the heating system in time.
If the heating system does not switch back on, proceed as follows:
1. Allow the appliance to cool down.
2. Unscrew the protective cap.
3. Press the button which is now visible and firmly screw the protective cap back on.
If the dry-boil protection triggers owing to increased scale deposits, descale the appli-
ance. See chapter 6.2 Consult your dealer if the fault was caused by a problem other
than the dry-boil protection being triggered.
On/off switch (1)
The on/off switch is used to switch the appliance on and off. Remember that the appli-
ance can still be live after switching it off! For this reason you should always remove the
plug from the socket to render the appliance voltage-free.
Jug detector (9)
This appliance is fitted with a jug detector that operates the leak stop under the filter.
This jug detector also ensures that the appliance only makes coffee if there is a jug
under the filter. If the jug is removed during the coffee brewing process, the process will
be interrupted and the filter will stop leaking.

2015/02 Rev. 4.0
M-LINE
25
GB
Appliances and the environment
The packing material
Your new coffee maker has been carefully packaged to protect it against damage.
The packing is not harmful to the environment and consists of the following materials:
• Corrugatedcardboard
• Fillerelementsmadeofpolyurethanefoam<PUR>coveredwithapolythenefilm
 (>PE-HD<).Thewasteprocessingplantinyourmunicipalitywillbepleasedto
inform you about where you can dispose of the materials.
Discarding the appliance
No appliance lasts forever. When the time comes to discard your appliance it will usually
be possible to return it to your dealer. If this is not the case, ask your municipal council
about the alternatives for recycling the materials. All plastic parts have been given stand-
ard codes. The parts of the appliance such as the printed circuit board and accompany-
ing parts form electrical and electronic waste. The metal body is made of stainless steel
and can be completely dismantled.

2015/02 Rev. 4.0
M-LINE
26 GB
1. GENERAL
1.1 A quick look at the appliance
The most important parts of the appliance are shown in the fold-out sheet in this manual.
Keep the fold-out sheet open when reading the instructions.
1.1.1 Most important parts
1. Appliance on/off switch coffee making 6. Water reservoir opening
section and bottom hot plate 7. Glass jug/thermos flask
2. On/off switch for top hot plate 8. Top hot plate
3. Basket filter with drip stop device 9. Jug detector
4. Basket filter paper 10. Bottom hot plate
5. Control panel coffee maker 11. Type plate
5.1 Descale indicator light 12. Water drain
5.2 Brewing process indicator light 13. Connection cable with plug
5.3 Selection button 14. Dry-boil protection
1.1.2 Control panel
The control panel has the following functions:
Descale indicator light (5.1); The red indicator light will light up if the
appliance needs to be descaled. The appliance will continue to work so that it
can be descaled when it is not being used. See also chapter 6.2.
Brewing process indicator light (5.2); The green indicator light lights up
when the coffee passes through the system. At the end of the coffee making
process a signal sounds three times and the green indicator light goes out.
The indicator light flickers if the jug is temporarily removed during the coffee
making process. A signal will also sound indicating that the coffee making
process has temporarily stopped.
Programming button (5.3); This key is made visible with a small triangle.
This programme key is used exclusively to : set the appliance to the local
water hardness. The red indicator light goes out when the appliance has been
descaled. See chapter 6.2.1.
Sound signals; Sounds three times at the end of the coffee making process.
Sounds once if the jug is removed during the coffee making process.
A long signal sounds when the appliance is switched on.
CAUTION
• Neverpressdebuttonswithasharpobject.
• Protectthecontrolsagainstdirtandgrease.

2015/02 Rev. 4.0
M-LINE
27
GB
2. TECHNICAL DETAILS
Model M100 M102 MT100 MT100v
Article number 10500/10501/10502 10551 10520/10521/10522 10537
Buffer stock coffee 3.6 l./ 28 cups 7.2 l. / 56 cups - -
Hourly coffee capacity 18 l./144 cups 36 l./288 cups 18 l./144 cups 18 l./144 cups
Jug filling time approx. 6 min. approx. 8 min. approx. 7,5 min./2.2 l. approx. 7,5 min./2.2 l.
Content water reservoir 2,7 l. 2,7 l 2,7 l. 2,7 l.
Supply voltage 220-240V~ 220-240V~ 220-240V~ 220-240V~
Frequency 50-60Cy 50-60Cy 50-60Cy 50-60Cy
Total output 2250W 3500W 2100W 2100W
Filter paper 90/250 90/250 90/250 90/250
Dimensions See fig. 1 See fig. 2 See fig. 3 See fig. 4
Empty weight 7,3 kg. 13,1 kg. 6,9 kg. 8,9 kg.
Transport dim. (lxwxh) 600x275x530 mm 600x490x540 mm 440x270x670 mm 440x270x670 mm
Transport weight 9,6 kg. 17,9 kg. 9 kg. 11 kg.
All technical details are subject to change
3. INSTALLATION
3.1 Unpacking
The machine has been carefully packed to prevent damage being caused to your new
coffee maker. Remove the packing carefully without using sharp objects. Check if the
appliance is complete. The appliance is delivered with the following accessories:
M100 M102 MT100 MT100v
Glass jug 2 4 - -
Basket filter 1 2 1 1
Filter paper (25 pcs.) 1 1 1 1
Coffee measuring cup 1 1 1 1
Water measuring cup - - 1 1
Coffee fur remover 1 1 1 1
Scale remover 1 1 1 1
Manual 1 1 1 1
Please contact your dealer if any parts are missing or damaged.

2015/02 Rev. 4.0
M-LINE
28 GB
3.2 Installation
3.2.1 Preparation for positioning the appliance
- Position the appliance at buffet height on a firm, level base that can bear the weight
of the appliance when it is filled.
- Position the appliance level and in such a way that it cannot cause any damage
if it leaks.
- The power connection must be situated within half a metre of the appliance.
- The owner must have these installation-technical preparations performed by qualified
engineers in accordance with general and local regulations.
- The service engineer may only connect the appliance to the prepared connections.
3.2.2 Electrical connection
Supply voltages and frequencies can differ between countries. Check if the appliance is
suitable for connection to the local power mains. Check if the details on the type plate
correspond. Connect the appliance to an earthed wall socket.
3.2.3 Water drainage
The water reservoir has a maximum content of 2.7 litres. If the reservoir is overfilled, the
excess water will be discharged via the drain at the bottom of the appliance. Take this
into account when positioning the appliance.
3.2.4 First time use
When used for the first time the appliance works according to the standard factory set-
tings. The various settings can be altered by authorised personnel. See chapter 5.
Settings.
1. Slide an empty basket filter (3) into the appliance and place an empty jug (with lid)
underneath it. NB! For the MT100(v) model leave the lid of the thermos jug with pump
open and leave the riser tube in the jug. Adjust the height of the MT100V before
positioning it. See 3.2.5.
2. Pour one jug (water measuring cup, MT-model) of cold water into the cold water
reservoir (6).
3. Wait for three minutes so that the entire heating system can de-aerate.
4. Check if the on/off switches (1 + 2, if present) are at position O.
5. Put the plug in the socket.
CAUTION
• Wateralwaysremainsintheheatingsystem:forthisreasontheappliancemustnot
be placed in an area where the temperature can fall below freezing point.
WARNING
• Ensurethatthemainsleaddoesnotcomeinto
contact with the hot plates (if present).

2015/02 Rev. 4.0
M-LINE
29
GB
6. Switch on the appliance by setting the on/off switch (1) to the I positio. The indicator
lights (5.1 and 5.2) will light up and an audible signal will sound.
The green indicator light (5.2) will now light up until the appliance has finished
making the coffee.
7. When the appliance has finished making the coffee, a signal will sound three times
fter about 1.5 minutes and the green indicator light (5.2) will go out.
8. Follow the above steps again for the other coffee making section if the model has a
double coffee making system (M102).
9. The appliance is ready for use when the jug has been emptied.
3.2.5 Height setting model MT100v
The MT200v model is in height adjustable. Follow the steps below to optimally set the
appliance to the height of the thermos flask being used.
1. Slide the basket filter (1) into the
appliance.
2. Grasp the top part of the appliance and
turn the adjustment button (2) a half-turn
anti clockwise.
3. Lift the top part of the appliance upwards.
4. Place the thermos jug you intend to use at
the base of the appliance.
5. Now slowly allow the top section to go
down until the marking line (3) on the
column is level with the top side of the
thermos jug. (This column height
adjustment must be done with the top
open if the appliance is used in
combination with a thermos jug with a
pump).
6. Tighten the adjustment button (clockwise).
7. After repositioning, check if the thermos
jug properly presses in the jug
detector handle (4) (the green indicator
light (5.2) must not blink when a coffee
making process begins).
3
4
1
5.2
2

2015/02 Rev. 4.0
M-LINE
30 GB
3.2.6 Setting the descale indicator
Scale deposits are left in the heating system when the appliance is used. The amount of
scaling depends on the hardness of the water being used. The coffee maker is fitted with
a descale indicator light (5.1), which lights up when the heating system has processed
a certain quantity of water and has to be descaled. The appliance continues to work so
that it can be descaled when it is not being used.
Position Indication lights Brewing processes Hardness
°D mmol/l °f
Soft  512 <8 <1,44 <14
Normal* 256 8 – 12 1,44 –2,16 14-21
Hard  128 >12 >2,16 >21
*Standard setting
If you are unaware of the hardness of your tap-water, you are advised to contact your
local water supply company.
Set the appliance to your water hardness as follows, using the table above as a
guideline.
1. Switch off the appliance (1)
2. Hold in the Selection button (5.3) and switch the appliance back on.
3. Press the Selection button (5.3) until the right indicator light (5.1 / 5.2) lights up.
(E.g. only the red lamp should light up for hard water).
4. Wait for 6 seconds. The water hardness has now been set.
3.2.7 Resetting the descale indicator light
After the descaling procedure (see chapter 6.2.1) hold in the selection button for
6 seconds. The descale indicator light will now go out.

2015/02 Rev. 4.0
M-LINE
31
GB
4. DAILY USE
When using the appliance you may find that certain settings do not entirely match your
requirements.
• Chapter5explainshowallsettingscanbeadjustedbyqualifiedpersonnel.
• Chapter6explainshowtheappliancemustbemaintainedbyqualifiedpersonnel.
4.1 Drip stop
This appliance is fitted with a drip stop that ensures that no coffee drips out of the filter
when you:
• Brieflytakeawaythejugduringthebrewingprocess:thejugdetector(9)‘sees’that
you have removed the jug and interrupts the brewing process.
A short audible signal will sound and the green indicator light (5.2) will flicker.
The brewing process will resume when you replace the jug.
• Takeawaythejugaftermakingcoffee.
• Aftermakingcoffeetakethefilteroutoftheappliancetoemptyit.
4.2 Coffee quantity
The amount of coffee can be measured using the coffee measuring cup supplied and
generally amounts to 35 to 50 grams per litre.
Jug Glass jug Thermos jug Thermos jug with pump Thermos container
Content 1.8 litres 1.8 litres 2.2 litres 2.4 litres
Coffee 65-90 grams 65-90 grams 75-110 grams 85-120 grams
NOTICE
• Theleakstopcanonlyworkifthejugdetectorispressedinsufficientlybythejug.
If you use a coffee jug with a narrow neck the jug detector will not be pressed in
sufficiently and the appliance will not start.
NOTICE
Basic instructions for brewing coffee
• Usefine-grindcoffee.
• Keepthejugsandthebasketfilterclean.

2015/02 Rev. 4.0
M-LINE
32 GB
4.3 Making coffee
1. Place a sheet of basket filter paper containing the desired amount of coffee (fine
grind type) in the basket filter. See the table above for the amount of coffee required.
2. Slide the basket filter (1) into the appliance.
3. Use a jug or water measuring cup (MT models) to pour fresh cold water into the
opening (6).
4. Then place the jug, with the lid on it, under the filter. NB! With the MT100 model open
the lid of the thermos jug with pump and leave the riser tube in the jug.
5. Switch on the appliance using the on/off switch (1). The lamp in the switch will go on
and the lower hot plate will switch on. The green indicatior light (5.2) will light up
and the coffee brewing process will begin.
6. Once the coffee brewing process has been completed the green indicatior light (5.2)
will go out and an audible signal will sound three times, indicating that the coffee is
ready. The jug can be removed before the filter has been completely emptied. Once
the filter has been cleaned you can immediately resume making coffee.
7. Pour out the coffee or place the jug on the top hot plate (8) (except for the MT
models). The top hot plate is switched on separately using on/off switch (2).
Always switch off the extra hot plate when it is not being used.
8. After cleaning the basket filter, the appliance can immediately be used to make the
next serving of coffee.
4.4 Making tea
This appliance can of course also be used to make tea using teabags.
• Basicrule:neveruseabasketfilterora(thermos)jugthathasalreadybeenusedto
make coffee. The coffee remnants will adversely affect the flavour of the tea.
• Tomaketeayoushouldthereforealwaysuseaseparateglassjug/thermosjugand
basket filter that have not been used to brew coffee!
• Placetheteabagsinthebasketfilterwithoutusingapaperfilterorplace/hangthem
in the jug. Tea is made using the same method as for brewing coffee, but without
using paper filters or coffee.
4.5 Termination of the brewing process?
• Switchtheon/offswitch(1)to‘off’,andtheprocesswillstop.Theprocesswill
continue when the on/off switch is switched back to ‘on’.
• Removethejugfromunderthefilter.Thejugdetector(9)willtemporarilyinterrupt
the coffee making process and the leak stop will prevent the filter (3) from dripping.
The green indicator light (5.2) will flicker, and a short audible signal will sound.
When the jug is replaced under the filter the coffee brewing process resumes and
will be completed.

2015/02 Rev. 4.0
M-LINE
33
GB
5. SETTINGS
NOTICE
•The prewet function can only be activated when the descale indicator light (5.1) does
not lights. When the descale indicator light (5.1) lights first descale the coffee
system, see chapter 6.2 Descaling. After descaling reset the descale indicator light,
see chapter 6.2.1 Switching-off the descale indicator light.
5.1 Setting of the prewet function
This appliance can make coffee using two methods:
• Continue-brew; (factory setting); The coffee making process begins immediately and
will pour hot water over the ground coffee without a waiting time.
• Prewet-brew; part of the hot water is first poured onto the ground coffee.
This causes the coffee to rise so that the smells and flavours are released.
The coffee making process then begins.
If you want to set the appliance to Prewet brew, this setting can be changed as follows:
1. Press the programme button (5.3) until the green indicator light (5.2) lights.
2. Press the programme button (5.3) again. The green indicator light (5.2) goes out and
the red indicator light (5.1) lights up.
3. Wait for 6 seconds. The Prewet brew function has now been saved.
4. How to switch off the prewet brew function; enter the same actions and change the
indicator light from red (5.1) to green (5.2).

2015/02 Rev. 4.0
M-LINE
34 GB
6. MAINTENANCE
6.1 Cleaning of the appliance and accessories
- Clean the outside of the appliance with a clean, damp cloth, if necessary using a
mild (non-abrasive) cleaning agent.
- Do not use an abrasive, as this will leave scratches and dull patches.
- The glass jugs and the basket filter can be washed normally and rinsed clean.
Please note, however, that it is inadvisable to clean the basket filter in an industrial
dish washer as its lightness may cause it to float and sustain damage.
- The thermos jug, thermos jug with pump and the filter can be rinsed with hot water.
- The coffee deposit in the coffee jugs and the filter can be cleaned with Animo coffee
fur remover. The appliance is supplied with one sachet of coffee fur remover.
It is easy to use.
6.1.1 Removing coffee deposits from glass jug and filter
1. Fill a tray with approx. 5 litres of warm water and dissolve a sachet of coffee fur
remover in it.
2. Place the parts you want to clean in this solution and leave them to soak for 15 to 30
minutes.
3. Then rinse them several times with hot water, and repeat when necessary.
4. Sprinkle the powder on to heavily soiled parts and clean them with a wet brush.
6.1.2 Removing coffee deposits from thermos jug
1. Dissolve a quantity of coffee fur remover in warm water: use approx. 2 grams
per litre.
2. Fill the thermos jug with this solution.
3. Leave the solution to soak for 15 to 30 minutes, then pour it away.
4. Rinse the jug thoroughly with hot water and repeat this several times.
WARNING
• Theappliancemustnotbesubmergedorsprayed.
• Never clean the hot plates (if present) with an
abrasive or sharp object. This way scratches on
the teflon surface will be prevented.