Anker Soundcore Infini Pro User manual

Soundcore Infini Pro
User Manual
Benutzerhandbuch | Manual del usuario | Manuel de l'utilisateur
Manuale utente | Manual do Usuário | 取扱説明書 | 사용 설명서
用户手册 | 使用者手冊 | Руководство пользователя
 | 

HDMI 2.0 cable Wall mount
positioning card
Soundcore Infini Pro Power cord
Remote control 2 × AAA batteries
Screws
Wall mount
brackets
12
3 4
56
7 8
User manual
9
User
manual !
WALLMOUNTING TEMPLATE
MARKHEREMARKHERE
453mm

EN
01
EN Safety Instructions
• Avoid dropping.
• Do not disassemble.
• Do not submerge in water.
• Avoid extreme temperatures.
• Do not use the device outdoors during thunderstorms.
• Use original or certified cables.
• Do not use any corrosive cleaner/oil to clean.
• The product should not be exposed to dripping or splashing water.
• Where the mains plug is used as the disconnect device, the disconnect device shall
remain readily operable.
At a Glance
1
2
53
4
HDMI TV AUX BLUETOOTH SOUND SURROUND
7
8
96
10
121618
15 1317
14
11
18
Front touchpad:
Power button
Source input button
Bluetooth button
Volume-down button
Volume-up button
Status indicator:
HDMI indicator
TV indicator
AUX indicator
Bluetooth indicator
Sound mode indicator
Surround indicator

02
EN
Rear:
AC IN
TV IN (OPT)
AUX IN
USB port
HDMI IN
HDMI OUT (ARC)
Wall mount screw holes
Placement
• Table Placement
1. Place the soundbar on a solid surface with the touch panel facing up.
• Wall Mount Installation
Step 1: Place the wall mount brackets over the wall mount screw holes on the rear
of the soundbar. Insert the 4 screws provided into the wall mount screw holes, then
fasten the screws.

03
EN Step 2: Place the wall mount positioning card against the wall, under your TV. Mark
the 2 bracket holes on the wall with a pencil, then drill two holes on the wall. Insert
two screws into the holes.
Step 3: Hang the soundbar on the wall.
450mm
Remote Control
1. Battery installation

04
EN2. Remote control buttons
1
2
3
9
11
12
13
10
8
4
5
6
7
Button Button functions
Power button Press to switch the soundbar on / o.
Note: the status indicator of the previously set input
source will flash when soundbar is turned on.
Source input button Select an input source for playback:
HDMI: Sound from a device connected via HDMI IN
TV: TV audio (TV IN (OPT) and HDMI OUT (ARC)
AUX: Sound from a device connected via AUX IN
BLUETOOTH: Sound from a Bluetooth device
Refer to d. Basic Operation chapter for details.
TV button Switch to TV source.
Previous Return to the previous track.
Play / Pause To pause/resume playback.
Sound mode buttons To activate movie, music, or voice mode.
Refer to e. Sound Modes chapter for more
information.

05
EN Button Button functions
Bass + and Bass -
buttons
To increase / decrease the bass.
Refer to g. Bass chapter for reference.
Surround To activate the Dolby Surround eect.
Refer to e. Playback with Surround sound chapter
for reference.
Mute button To temporarily turn o the sound. Press the button
again to turn the sound back on.
Bluetooth button To activate Bluetooth mode.
Press to activate Bluetooth mode.
Refer to c. Bluetooth mode chapter for information.
Volume-up button To increase the volume.
Next Move to the next track.
Volume-down button To decrease the volume.
Using Your Soundbar
HDMI TV AUX BLUETOOTH SOUND SURROUND
Note: The soundbar will automatically switch to standby mode when no audio input
is received for 15 minutes. The soundbar will wake up from standby mode when any
button is pressed or source input is received.

06
EN
a. Connect to your TV
HDMI ARC connection (For TVs that support ARC)
Note: The Audio Return Channel (ARC) function enables an HDMI compatible TV to
send the audio stream to HDMI OUT of the unit.
1. Connect HDMI cable to the HDMI OUT (ARC) port on the rear of the soundbar.
2. Connect the other end of the HDMI cable to the HDMI IN ARC port on the TV.
3. Tap the source input button on the soundbar or remote control to activate the
corresponding mode.
Optical connection (For TVs that do not support ARC)
1. Connect the optical cable to the TV IN (OPT) jack on the rear of the soundbar.
2. Connect the other end of the optical cable to audio output jack on TV.
3. Tap the source input button on the soundbar or remote control to activate the
corresponding mode.
Note: The TV IN (OPT) jack cannot be used when a TV that supports the Audio Return
Channel is connected to the soundbar.

07
EN b. Connect to other devices
HDMI IN connection
1. Connect the HDMI cable to the HDMI IN port on the rear of the soundbar.
2. Connect the other end of the HDMI cable to the HDMI output port on the playback
devices.
3. Tap the source input button on the soundbar or remote control to activate the
corresponding mode.
AUX connection
1. Connect the audio cable to the AUX IN port on the rear of the soundbar.
2. Connect the other end of AUX cable (not provided) to the audio output jack on the
device.
3. Tap the source input button on the soundbar or remote control to activate the
corresponding mode.
Note: Follow your device's user manual if you want to connect the soundbar to your
other devices (such as Blu-ray player, game console, tablet, MP3 Player, laptop etc).
Note: 3.5mm to 3.5mm cable is not included.

08
EN
c. Bluetooth Mode
Bluetooth ON
Soundcore
Infini Pro
1. Press power button on the remote control to switch on the soundbar.
2. Press the Bluetooth button on the remote control to activate Bluetooth pairing
mode.
3. Turn on the Bluetooth of your device, search for Soundcore Infini Pro on your
Bluetooth list then select connect.
Flashing white (Bluetooth indicator) Bluetooth mode is activated
Solid white Connected to device
Hold Bluetooth button for 3 seconds to activate Bluetooth pairing mode.
Having connection problems? Remove Soundcore Infini Pro from your
device’s Bluetooth history and ensure it’s less than 10 meters away. Then
try pairing again. To get the best sound quality, make sure there is a clear
line of sight between the connected device and your soundbar.
T