Anritsu MP1570A User manual

Document No.: M-W1721AE-11.0
ANRITSU CORPORATION
MP1570A
SONET/SDH/PDH/ATM Analyzer
Operation Manual
Vol.2
Remote Control
11th Edition
•
Read this manual before using the equipment.
•To ensure that the equipment is used safely, read the
"For Safety" in the MP1570A SONET/SDH/PDH/ATM
Analyzer Operation Manual first.
•Keep this manual with the equipment.

ii
Safety Symbols
To prevent the risk of personal injury or loss related to equipment malfunction, Anritsu Corporation uses the following
safety symbols to indicate safety-related information. Insure that you clearly understand the meanings of the symbols
BEFORE using the equipment. Some or all of the following five symbols may not be used on all Anritsu equipment.
In addition, there may be other labels attached to products which are not shown in the diagrams in this manual.
Symbols used in manual
This indicates a very dangerous procedure that could result in serious injury or
death if not performed properly.
This indicates a hazardous procedure that could result in serious injury or death if
not performed properly.
This indicates a hazardous procedure or danger that could result in light-to-severe
injury, or loss related to equipment malfunction, if proper precautions are not taken.
Safety Symbols Used on Equipment and in Manual
The following safety symbols are used inside or on the equipment near operation locations to provide information
about safety items and operation precautions. Insure that you clearly understand the meanings of the symbols
and take the necessary precautions BEFORE using the equipment.
This indicates a prohibited operation. The prohibited operation is indicated sym-
bolically in or near the barred circle.
This indicates an obligatory safety precaution. The obligatory operation is indicat-
ed symbolically in or near the circle.
This indicates warning or caution. The contents are indicated symbolically in or
near the triangle.
This indicates a note. The contents are described in the box.
These indicate that the marked part should be recycled.
MP1570A
SONET/SDH/PDH/ATM Analyzer
Operation Manual Vol.2 Remote Control
23 February 2000 (First Edition)
27 September 2005 (11th Edition)
Copyright © 2000-2005, ANRITSU CORPORATION.
All rights reserved. No part of this manual may be reproduced without the prior written permission of the
publisher.
The contents of this manual may be changed without prior notice.
Printed in Japan
DANGER
WARNING
CAUTION

iii
Equipment Certificate
Anritsu Corporation certifies that this equipment was tested before ship-
ment using calibrated measuring instruments with direct traceability to
public testing organizations recognized by national research laboratories
including the National Institute of Advanced Industrial Science and Tech-
nology, and the National Institute of Information and Communications
Technology, and was found to meet the published specifications.
Anritsu Warranty
Anritsu Corporation will repair this equipment free-of-charge if a mal-
function occurs within 1 year after shipment due to a manufacturing fault,
provided that this warranty is rendered void under any or all of the fol-
lowing conditions.
•The fault is outside the scope of the warranty conditions described in
the operation manual.
•The fault is due to mishandling, misuse, or unauthorized modification
or repair of the equipment by the customer.
•The fault is due to severe usage clearly exceeding normal usage.
•The fault is due to improper or insufficient maintenance by the cus-
tomer.
•The fault is due to natural disaster including fire, flooding, earthquake,
etc.
•The fault is due to use of non-specified peripheral equipment,
peripheral parts, consumables, etc.
•The fault is due to use of a non-specified power supply or in a non-
specified installation location.
In addition, this warranty is valid only for the original equipment pur-
chaser. It is not transferable if the equipment is resold.
Anritsu Corporation will not accept liability for equipment faults due to
unforeseen and unusual circumstances, nor for faults due to mishandling
by the customer.
Anritsu Corporation Contact
In the event that this equipment malfunctions, contact an Anritsu Service
and Sales office. Contact information can be found on the last page of the
printed version of this manual, and is available in a separate file on the
CD version.

iv
Notes On Export Management
This product and its manuals may require an Export License/Approval by
the Government of the product's country of origin for re-export from you
r
country.
Before re-exporting the product or manuals, please contact us to confirm
whether they are export-controlled items or not.
When you dispose of export-controlled items, the products/manuals are
needed to be broken/shredded so as not to be unlawfully used for military
purpose.

v
Crossed-out Wheeled Bin Symbol
Equipment marked with the Crossed-out Wheeled Bin Symbol complies
with council directive 2002/96/EC (the “WEEE Directive”) in European
Union.
For Products placed on the EU market after August 13, 2005, please con-
tact your local Anritsu representative at the end of the product's useful life
to arrange disposal in accordance with your initial contract and the local
law.

vi
CE Conformity marking
Anritsu affixes the CE Conformity marking on the following product (s) in
accordance with the Council Directive 93/68/EEC to indicate that they
conform with the EMC and LVD directive of the European Union (EU).
CE marking
1. Product Model
Model: MP1570A SONET/SDH/PDH/ATM ANALYZER
and
Plug-in Units: See Table 1.
2. Applied Directive
EMC: Council Directive 89/336/EEC
LVD: Council Directive 73/23/EEC
3. Applied Standards
•EMC:Emission: EN61326: 1997 / A2: 2001 (Class A)
Immunity:EN61326: 1997 / A2: 2001 (Annex A)
Performance Criteria*
IEC 61000-4-2 (ESD) B
IEC 61000-4-3 (EMF) A
IEC 61000-4-4 (Burst) B
IEC 61000-4-5 (Surge) B
IEC 61000-4-6 (CRF) A
IEC 61000-4-8 (RPFMF) A
IEC 61000-4-11 (V dip/short) B
*: Performance Criteria
A: During testing normal performance within the specifi-
cation limits
B: During testing, temporary degradation, or loss of
function or performance which is self-recovering
Harmonic current emissions:
EN61000-3-2: 2000 (Class A equipment)
•LVD: EN61010-1: 2001 (Pollution Degree 2)

vii
C-tick Conformity marking
Anritsu affixes the C-tick marking on the following product (s) in accor-
dance with the regulation to indicate that they conform with the EMC
framework of Australia/New Zealand.
C-tick marking
1. Product Model
Model: MP1570A SONET/SDH/PDH/ATM ANALYZER
and
Plug-in Units: See Table 1.
2. Applied Standards
EMC: Emission:
AS/NZS 2064.1 / 2 (ISM, Group 1, Class A equipment)

viii
Table 1 List of the Product Name and Model Name
Model Name Product Name
Main Frame
MP1570A SONET/SDH/PDH/ATM ANALYZER
Plug in Units
MP0105A CMI UNIT
MP0108A NRZ UNIT
MP0111A Optical 156M/622M (1.31) UNIT
MP0112A Optical 156M/622M (1.55) UNIT
MP0113A Optical 156M/622M (1.31/1.55) UNIT
MP0121A 2/8/34/139/156M UNIT
MP0122A 1.5/45/52M UNIT
MP0122B 1.5/45/52/52M (1.31) UNIT
MP0123A ATM UNIT
MP0124A 2/8/34/139M 156/622M Jitter UNIT
MP0125A 1.5/45/52M 156/622M Jitter UNIT
MP0126A 2/8/34/139M 1.5/45/52M 156/622M Jitter UNIT
MP0127A 2.5G (1.31) UNIT
MP0128A 2.5G (1.55) UNIT
MP0129A 2.5G (1.31/1.55) UNIT
MP0130A 2.5G Jitter UNIT
MP0131A Add/Drop UNIT
MU150000A 2.5G/10G UNIT
MU150001A Optical 10G Tx (1.55) UNIT
MU150001B Optical 10G Tx (1.55) UNIT
MU150002A Optical 10G Rx (narrow) UNIT
MU150005A 2/8/34/139M 156/622M Jitter UNIT
MU150006A 1.5/45/52M 156/622M Jitter UNIT
MU150007A 2/8/34/139M 1.5/45/52M 156/622M Jitter UNIT
MU150008A 2.5G (1.31) UNIT
MU150009A 2.5G (1.55) UNIT
MU150010A 2.5G (1.31/1.55) UNIT
MU150011A 2.5G Jitter UNIT
MU150017A Optical 10G Rx (Wide) Unit
MU150017B Optical 2.5G/10G Rx (Wide) Unit
MU150031A Optical 10G (1.55) High Power Tx Unit
MU150031C Optical 2.5G (1.55)/10G (1.55) High Power Tx Unit
MU150061A Optical 10G (1.31) Tx Unit
MU150061B Optical 2.5G (1.31)/10G (1.31) Tx Unit
MU154882A GPIB/ETHERNET INTERFACE

About MP1570A Operation Manuals
I
Basic Operation SDH Edition
Basic O
p
eration SONET Edition
(
this manual
)
Remote Control
(
this manual
)
Describes the remote control and program examples
using the GPIB and RS-232C interfaces. (MP1570A is
compatible with SPCI).
A
TM Measurment
Describes the contents of screens, operation procedures
and remote control for the generation and analysis of
the ATM signal.
2.5G/10G Measurement
Describes the contents of screens, operation procedures
and remote control for the generation and analysis of
2.5G (STM16) and 10G (STM64) signals.
A
dd/Dro
p
Measurement
Describes the contents of screens, operation procedures
and remote control for the generation and analysis of
Add/Drop.
Jitter/Wander Measurement
Describes the contents of screens, operation procedures
and remote control for the generation and analysis of
Jitter (TX)/Frequency offset and Jitter (RX).
2.5G Jitter/Wander Measurement
Describes the contents of screens, operation procedures
and remote control for the generation and analysis of
2.5G Jitter (TX)/Frequency offset and Jitter (RX).
MP1570A SONET/SDH/PDH/ATM Analyzer Operation Manuals
comprise of the following eight documents. Use them properly
according to the usage purpose.
Organization of MP1570A
Operation Manuals
Describes the basic operation of MP1570A, PDH mea-
surement and SDH measurements up to 622M (STM
4). (The contents of this manual are basically the sa
me as those of ‘Basic Operation SONET Edition’).
Describes the basic operation of MP1570A, DSn mea-
surement and SONET measurement of up to 622M
(STS12). (The contents of this manual are basically t
he same as those of ‘Basic Operation SDH Edition’.).
Vol. 1
Vol. 2
Vol. 3
Vol. 4
Vol. 5
Vol. 6
Vol. 7

About MP1570A Operation Manuals
II