Anritsu MS2690A User manual

Document No.: M-W3655AE-1.0
ANRITSU CORPORATION
MS2690A/MS2691A/MS2692A
and MS2830A
Signal Analyzer
Operation Manual
Noise Figure Measurement Function
Operation
First Edition
•
For safety and warning information, please read this
manual before attempting to use the equipment.
•
Additional safety and warning information is
provided within the MS2690A/MS2691A/MS2692A
Signal Analyzer Operation Manual
(Mainframe
Operation) or MS2830
A Signal Analyzer Operation
Manual (Mainframe Operation). Please also refer
to
this document before using the equipment.
•
Keep this manual with the equipment.

ii
Safety Symbols
To prevent the risk of personal injury or loss related to equipment malfunction, Anritsu Corporation uses the
following safety symbols to indicate safety-related information. Ensure that you clearly understand the meanings of
the symbols BEFORE using the equipment. Some or all of the following symbols may be used on all Anritsu
equipment. In addition, there may be other labels attached to products that are not shown in the diagrams in this
manual.
Symbols used in manual
This indicates a very dangerous procedure that could result in serious injury or
death if not performed properly.
This indicates a hazardous procedure that could result in serious injury or death if
not performed properly.
This indicates a hazardous procedure or danger that could result in light-to-severe
injury, or loss related to equipment malfunction, if proper precautions are not taken.
Safety Symbols Used on Equipment and in Manual
The following safety symbols are used inside or on the equipment near operation locations to provide information
about safety items and operation precautions. Ensure that you clearly understand the meanings of the symbols and
take the necessary precautions BEFORE using the equipment.
This indicates a prohibited operation. The prohibited operation is indicated
symbolically in or near the barred circle.
This indicates an obligatory safety precaution. The obligatory operation is
indicated symbolically in or near the circle.
This indicates a warning or caution. The contents are indicated symbolically in or
near the triangle.
This indicates a note. The contents are described in the box.
These indicate that the marked part should be recycled.
MS2690A/MS2691A/MS2692A and MS2830A
Signal Analyzer
Operation Manual Noise Figure Measurement Function Operation
23 October 2012 (First Edition)
Copyright © 2012, ANRITSU CORPORATION.
All rights reserved. No part of this manual may be reproduced without the prior written permission of the
publisher.
The contents of this manual may be changed without prior notice.
Printed in Japan
DANGER
WARNING
CAUTION

iii
Equipment Certificate
Anritsu Corporation guarantees that this equipment was inspected at
shipment and meets the published specifications.
Anritsu Warranty
•During the warranty period, Anritsu Corporation will repair or exchange this
software free-of-charge if it proves defective when used as described in the
operation manual.
•The warranty period is 6 months from the purchase date.
•The warranty period after repair or exchange will remain 6 months from
the original purchase date, or 30 days from the date of repair or
exchange, depending on whichever is longer.
•This warranty does not cover damage to this software caused by Acts of
God, natural disasters, and misuse or mishandling by the customer.
In addition, this warranty is valid only for the original equipment purchaser. It
is not transferable if the equipment is resold.
Anritsu Corporation shall assume no liability for injury or financial loss of the
customer due to the use of or a failure to be able to use this equipment.
Anritsu Corporation Contact
In the event that this equipment malfunctions, contact an Anritsu Service and
Sales office. Contact information can be found on the last page of the printed
version of this manual, and is available in a separate file on the CD version.

iv
Notes On Export Management
This product and its manuals may require an Export License/Approval by
the Government of the product's country of origin for re
-
export from your
country.
Bef
ore re-
exporting the product or manuals, please contact us to confirm
whet
her they are export-controlled items or not.
When you dispose of export
-
controlled items, the products/manuals need
to be broken/shredded so as not to be unlawfully used for military purpose.
Cautions against computer virus infection
•Copying files and data
Only files that have been provided directly from Anritsu or generated
using Anritsu equipment should be copied to the instrument.
All other required files should be transf
erred by means of USB or
CompactFlash media after undergoing a thorough virus check.
•Adding software
Do not download or install software that has not been specifically
recommended or licensed by Anritsu.
•Network connections
Ensure that the network has sufficient anti-
virus security protection in
place
.

v
Software End-User License Agreement (EULA)
Please read this Software End-User License Agreement (hereafter this EULA) carefully before using
(includes executing, copying, registering, etc.) this software (includes programs, databases, scenarios,
etc., used to operate, set, etc., Anritsu electronic equipment). By reading this EULA and using this
software, you are agreeing to be bound by the terms of its contents and Anritsu Corporation (hereafter
Anritsu) hereby grants you the right to use this Software with the Anritsu-specified equipment
(hereafter Equipment) for the purposes set out in this EULA.
1. Grant of License and Limitations
1. Regardless of whether this Software was
purchased from or provided free-of-charge by
Anritsu, you agree not to rent, lease, lend, or
otherwise distribute this Software to third
parties and further agree not to disassemble,
recompile, reverse engineer, modify, or create
derivative works of this Software.
2. You may make one copy of this Software for
backup purposes only.
3. You are not permitted to reverse engineer
this software.
4. This EULA allows you to install one copy of
this Software on one piece of Equipment.
2. Disclaimers
To the extent not prohibited by law, in no
event shall Anritsu be liable for personal
injury, or any incidental, special, indirect or
consequential damages whatsoever,
including, without limitation, damages for
loss of profits, loss of data, business
interruption or any other commercial
damages or losses, arising out of or related
to your use or inability to use this Software.
3. Limitation of Liability
a. If a fault (bug) is discovered in this Software,
preventing operation as described in the
operation manual or specifications whether
or not the customer uses this software as
described in the manual, Anritsu shall at its
own discretion, fix the bug, or exchange the
software, or suggest a workaround,
free-of-charge. However, notwithstanding
the above, the following items shall be
excluded from repair and warranty.
i) If this Software is deemed to be used for
purposes not described in the operation
manual or specifications.
ii) If this Software is used in conjunction with
other non-Anritsu-approved software.
iii) Recovery of lost or damaged data.
iv) If this Software or the Equipment has been
modified, repaired, or otherwise altered
without Anritsu's prior approval.
v) For any other reasons out of Anritsu's direct
control and responsibility, such as but not
limited to, natural disasters, software virus
infections, etc.
b. Expenses incurred for transport, hotel, daily
allowance, etc., for on-site repairs by Anritsu
engineers necessitated by the above faults
shall be borne by you.
c. The warranty period for faults listed in
article 3a above covered by this EULA shall
be either 6 months from the date of purchase
of this Software or 30 days after the date of
repair, whichever is longer.

vi
4. Export Restrictions
You may not use or otherwise export or
re-export directly or indirectly this Software
except as authorized by Japanese and
United States law. In particular, this
software may not be exported or re-exported
(a) into any Japanese or US embargoed
countries or (b) to anyone on the Japanese or
US Treasury Department's list of Specially
Designated Nationals or the US Department
of Commerce Denied Persons List or Entity
List. By using this Software, you warrant
that you are not located in any such country
or on any such list. You also agree that you
will not use this Software for any purposes
prohibited by Japanese and US law,
including, without limitation, the
development, design and manufacture or
production of missiles or nuclear, chemical
or biological weapons of mass destruction.
5. Termination
Anritsu shall deem this EULA terminated if
you violate any conditions described herein.
This EULA shall also be terminated if the
conditions herein cannot be continued for
any good reason, such as violation of
copyrights, patents, or other laws and
ordinances.
6. Reparations
If Anritsu suffers any loss, financial or
otherwise, due to your violation of the terms
of this EULA, Anritsu shall have the right to
seek proportional damages from you.
7. Responsibility after Termination
Upon termination of this EULA in
accordance with item 5, you shall cease all
use of this Software immediately and shall
as directed by Anritsu either destroy or
return this Software and any backup copies,
full or partial, to Anritsu.
8. Dispute Resolution
If matters of dispute or items not covered by
this EULA arise, they shall be resolved by
negotiations in good faith between you and
Anritsu.
9. Court of Jurisdiction
This EULA shall be interpreted in
accordance with Japanese law and any
disputes that cannot be resolved by
negotiation described in Article 8 shall be
settled by the Japanese courts.

I
About This Manual
Associated Documents
The operation manual configuration of the MS2690A/MS2691A/MS2692A
and MS2830A Signal Analyzer is shown below.
MS2690A/MS2691A/MS2692A
Signal Analyzer Operation Manual
(Main Frame Operation)
MS2690A/MS2691A/MS2692A and MS2830A Signal Analyzer Operation Manual
(Noise Figure Measurement Function Operation)
MS2690A/MS2691A/MS2692Aand MS2830A Signal Analyzer Operation Manual
(Noise Figure Measurement Function Remote Control)
MS2690A/MS2691A/MS2692A and MS2830A
Signal Analyzer Operation Manual (Main Frame Remote Control)
MS2830A Signal Analyzer
Operation Manual
(Main Frame Operation)Or
MS2690A/MS2691A/MS2692A
Signal Analyzer Operation Manual
(Signal Analyzer Function
Operation)
MS2690A/MS2691A/MS2692A and MS2830A Signal Analyzer Operation Manual
(Signal Analyzer Function Remote Control)
MS2830A
Signal Analyzer Operation Manual
(Signal Analyzer Function
Operation)
Or
MS2690A/MS2691A/MS2692A
Spectrum Analyzer Operation Manual
(Spectrum Analyzer Function
Operation)
MS2690A/MS2691A/MS2692A and MS2830A
Signal Analyzer Operation Manual (Spectrum Analyzer Function Remote Control)
MS2830A
Spectrum Analyzer Operation Manual
(Spectrum Analyzer Function
Operation)
Or

II
• Signal Analyzer Operation Manual (Mainframe)
• Signal Analyzer Operation Manual (Mainframe Remote Control)
Description of basic operations, maintenance procedures, common
functions and common remote functions of the mainframe
• Signal Analyzer Operation Manual (Signal Analyzer Function)
• Signal Analyzer Operation Manual (Signal Analyzer Function Remote Control)
Description of basic operations, common functions and common remote
functions of the signal analyzer
• Signal Analyzer Operation Manual (Spectrum Analyzer Function)
• Signal Analyzer Operation Manual (Spectrum Analyzer Function Remote
Control)
Description of basic operations, common functions and common remote
functions of the spectrum analyzer
• Signal Analyzer Operation Manual (Noise Figure Measurement Function)
<This document>
• Signal Analyzer Operation Manual (Noise Figure Measurement Function
Remote Control)
Description of basic operations, common functions and common remote
functions of the Phase Noise Measurement function
Convention Used in This Manual
Throughout this document, the use of MS269x Series is assumed unless
otherwise specified.
If using MS2830A, change MS269xA to read MS2830A.
In this document, indicates a panel key.

1
III
2
3
4
Appendix Index
5
Table of Contents
About This Manual........................................ I
Chapter 1 Overview.................................... 1-1
1.1 Product Overview.......................................................... 1-2
1.2 Product Composition..................................................... 1-3
1.3 Specifications................................................................ 1-5
Chapter 2 Before Use................................. 2-1
2.1 Part Names................................................................... 2-2
2.2 Signal Path Setup......................................................... 2-12
2.3 Application Startup and Selection................................. 2-13
2.4 Initialization and Calibration.......................................... 2-14
Chapter 3 Measurement ............................ 3-1
3.1 Basic Operation ............................................................ 3-2
3.2 Setting Frequency......................................................... 3-5
3.3 Setting Level ................................................................. 3-10
3.4 Setting Common Items ................................................. 3-12
3.5 Setting the Measure Function....................................... 3-24
3.6 Setting the Marker Function.......................................... 3-28
3.7 Setting the Peak Search Function ................................ 3-29
3.8 Measurement Results................................................... 3-31
Chapter 4 Other Functions ...................... 4-1
4.1 Selecting Other Functions............................................. 4-2
4.2 Setting Title................................................................... 4-2
4.3 Deleting Warm-up Message ......................................... 4-2
Chapter 5 Performance Test .................... 5-1
5.1 Overview of Performance Test..................................... 5-2
5.2 Power Port Operation Check........................................ 5-4

IV.
Appendix A Error Message.......................... A-1
Appendix B Default Value List..................... B-1
Index .......................................................... Index-1

Chapter 1Overview
1-1
1
Overview
This chapter provides an overview of the MX269028A WLAN (802.11)
Measurement Software and describes the product configuration.
1.1 Product Overview........................................................1-2
1.2 Product Composition...................................................1-3
1.2.1 Option / Software ............................................1-3
1.2.2 Noise Source ..................................................1-3
1.3 Specifications..............................................................1-5

Chapter 1 Overview
1-2
1.1 Product Overview
The MS2690/MS2691/MS2692A or MS2830A Signal Analyzer enables
high-speed, high-accuracy, and simple measurements of transmission
characteristics of base stations and mobile stations for various types of
mobile communications.
The Noise Figure Measurement Function (hereinafter, this application) is
to measure Noise Figure (hereinafter, NF) which has a huge effect on
noise in systems that handle minute signals such as satellite
communications and radars. It can be used in various fields such as
evaluations of transceivers and devices and troubleshooting.
NF is measured with the measurement method of Y-factor method which
uses a Noise Source.
The NC346 Series noise sources by Noisecom company are supported

1.2 Product Composition
1-3
1
Overview
1.2 Product Composition
1.2.1 Option / Software
Table 1.2-1 list the Options and Software’s.
Table1.2.1-1 Configuration of Application
Model/Symbol Product name Remarks
MS2690A-017
MS2691A-017
MS2692A-017
Noise Figure Measurement Function
MS2690A-117
MS2691A-117
MS2692A-117
Noise Figure Measurement Function
Retrofit
MS2830A-017 Noise Figure Measurement Function
MS2830A-117
Noise Figure Measurement Function
Retrofit
The MS269xA-017/117 and MS269xA-030 W-CDMA RNC simulator are
exclusive options.
1.2.2 Noise Source
The NC346 Series noise sources by Noisecom company are supported.
The models and specifications outlines of NC346 Series are as follows.
For detailed specifications, refer to the catalog and data sheet for the
NC346 Series.
Table1.2.2-1 Specifications of NC346 Series
Model DC Offset Frequency
[GHz] Output ENR [dB]
NC346A
–
0.01-18.0
5-7
NC346B
–
0.01-18.0
14-16
NC346D
–
0.01-18.0
19-25
NC346C

0.01-26.5
13-17
NC346E

0.01-26.5
19-25
NC346Ka

0.10-40.0
10-17

Chapter 1 Overview
1-4
CAUTION
Some noise sources output DC power. Therefore, when
selecting a model from the following models of the RF
input specification “0V_DC_max”, install a DC block:
・MS2690A-017/-117
・MS2691A-017/-117
・MS2692A-017/-117
・MS2830A-044, -017/-117
・MS2830A-045, -017/-117

1.3 Specifications
1-5
1
Overview
1.3 Specifications
Table 1.3-1 show the specifications.
Table 1.3-1 Specifications for this Application
Item Specification
MS269xA MS2830A
Frequency
Frequency
range
MS2690A: 30 MHz to 6 GHz
MS2691A: 30 MHz to 6 GHz
MS2692A: 30 MHz to 6 GHz
MS2830A-040:
30 MHz to 3.6 GHz
MS2830A-041: 30 MHz to 6 GHz
MS2830A-043: 30 MHz to 6 GHz
MS2830A-044:
(MS2830A-068/168 is not installed)
30 MHz to 6 GHz
MS2830A-044:
(MS2830A-068/168 is installed)
30 MHz to 26.5 GHz
MS2830A-045:
(MS2830A-068/168 is not installed)
30 MHz to 6 GHz
MS2830A-045:
(MS2830A-068/168 is installed)
30 MHz to 40 GHz
Frequency
Setting range
MS2690A: 10 MHz to 6 GHz
MS2691A:
10 MHz to 13.5 GHz
MS2692A:
10 MHz to 26.5 GHz
MS2830A-040:
10 MHz to 3.6 GHz
MS2830A-041: 10 MHz to 6 GHz
MS2830A-043:
10 MHz to 13.5 GHz
MS2830A-044:
10 MHz to 26.5 GHz
MS2830A-045:
10 MHz to 43 GHz
NF
Measurem
ent
Measurement
range Within the frequency range
(Attenuator = 0dB, Pre-Amp = On)
– 20 to 40 dB
Instrument
Uncertainty
Within the measurement range
ENR：4-7 dB ±0.02 dB
ENR：12-17 dB ±0.025 dB
ENR
：
20-22 dB ±0.03 dB

Chapter 1 Overview
1-6
Table 1.3-1 Specifications for this Application (continued)
Item Specification
GAIN
Measure
ment
Measurement
range
Within the frequency range
–20 to +40 dB
Instrument
Uncertainty
Within the measurement range
≦
0.07
Resolution
Bandwidth
Setting Range
100 kHz to 8 MHz
Noise
Source
－
Recommending the NC346 Series noise sources by Noisecom
company
Connector
Noise Source
Connector: Rear Panel, BNC-J
•Output Voltage:28±0.5 V, Pulsed

1.3 Specifications
1-7
1
Overview
Table 1.3-1 Specifications (Continued)
Item Specification
Target signal
IEEE 802.11ac
Modulation/Frequency measurement
Transmitter power accuracy
40 MHz channel
After CAL execution at 18º to 28ºC, input attenuator ≥ 10 dB,
The signal measured is within the measurement level range and less
than or equal to Input Level.
MS269xA series:
± 0.7 dB (at Pre-Amp Off, or Pre-Amp not installed.)
± 1.1 dB (at Pre-Amp On)
MS2830A:
± 2.0 dB (at Pre-Amp Off, or Pre-Amp not installed.)
The transmitter power accuracy is obtained by an RSS (root summed
square) error of the absolute amplitude accuracy and in-band frequency
characteristics.
Transmitter power accuracy
80 MHz channel
After CAL execution at 18º to 28ºC, input attenuator ≥ 10 dB,
The signal measured is within the measurement level range and less
than or equal to Input Level.
MS269xA series:
± 1.2 dB (at Pre-Amp Off, or Pre-Amp not installed.)
± 1.6 dB (at Pre-Amp On)
MS2830A:
± 3.2 dB (at Pre-Amp Off, or Pre-Amp not installed.)
The transmitter power accuracy is obtained by an RSS (root summed
square) error of the absolute amplitude accuracy and in-band frequency
characteristics.
Transmitter power accuracy
160 MHz channel
After CAL execution at 18º to 28ºC, input attenuator ≥ 10 dB,
The signal measured is within the measurement level range and less
than or equal to Input Level.
MS269xA series:
± 1.3 dB (at Pre-Amp Off, or Pre-Amp not installed.)
± 1.7 dB (at Pre-Amp On)
The transmitter power accuracy is obtained by an RSS (root summed
square) error of the absolute amplitude accuracy and in-band frequency
characteristics.
Center frequency leak floor
≤ –50 dBc (Nominal)

Chapter 1 Overview
1-8.

Chapter 2 Preparation
2-1
2
Preparation
This chapter describes the preparations required for using the
application you are using. Refer to the “MS2690A/MS2691A/MS2692A
Signal Analyzer Operation Manual (Mainframe Operation)” or “MS2830A
Signal Analyzer Operation Manual (Mainframe Operation)” for common
features not included in this manual.
2.1 Part Names...................................................................2-2
2.1.1 Front panel .......................................................2-2
2.1.2 Rear panel........................................................2-8
2.2 Signal Path Setup.......................................................2-12
2.3 Application Startup and Selection...............................2-13
2.3.1 Launching application.....................................2-13
2.3.2 Selecting application.......................................2-13
2.4 Initialization and Calibration........................................2-14
2.4.1 Initialization.....................................................2-14
2.4.2 Calibration ......................................................2-14

Chapter 2 Preparation
2-2
2.1 Part Names
This section describes the panel keys for operating the instrument and
connectors used to connect external devices. For general points of caution,
refer to the “MS2690A/MS2691A/MS2692A Signal Analyzer Operation
Manual (Mainframe Operation)” or “MS2830A Signal Analyzer Operation
Manual (Mainframe Operation)”.
2.1.1 Front panel
This section describes the front-panel keys and connectors.
1
2
3
4
5
6
7
8
9
19 17 18 16
11
13
10 12
14
15
Figure 2.1.1-1 MS269x series front panel
9
8
7
6
5
4
3 21
17
20
18
19 16
11
15
13
10 21 1
2
14
22
Figure 2.1.1-2 MS2830A front panel