Anritsu MP2100A BERTWave User manual

Document No.: M-W3349AE-15.0
ANRITSU CORPORATION
MP2100A BERTWave
MP2101A BERTWave PE
MP2102A BERTWave SS
Operation Manual
For safety and warning information, please read this
manual before attempting to use the equipment.
Keep this manual with the equipment.
15th Edition

ii
Safety Symbols
To prevent the risk of personal injury or loss related to equipment malfunction, Anritsu Corporation uses the
following safety symbols to indicate safety-related information. Ensure that you clearly understand the meanings of
the symbols BEFORE using the equipment. Some or all of the following symbols may be used on all Anritsu
equipment. In addition, there may be other labels attached to products that are not shown in the diagrams in this
manual.
Symbols used in manual
This indicates a very dangerous procedure that could result in serious injury or
death if not performed properly.
This indicates a hazardous procedure that could result in serious injury or death if
not performed properly.
This indicates a hazardous procedure or danger that could result in light-to-severe
injury, or loss related to equipment malfunction, if proper precautions are not taken.
Safety Symbols Used on Equipment and in Manual
The following safety symbols are used inside or on the equipment near operation locations to provide information
about safety items and operation precautions. Ensure that you clearly understand the meanings of the symbols and
take the necessary precautions BEFORE using the equipment.
This indicates a prohibited operation. The prohibited operation is indicated
symbolically in or near the barred circle.
This indicates an obligatory safety precaution. The obligatory operation is
indicated symbolically in or near the circle.
This indicates a warning or caution. The contents are indicated symbolically in or
near the triangle.
This indicates a note. The contents are described in the box.
These indicate that the marked part should be recycled.
MP2100A BERTWave
MP2101A BERTWave PE
MP2102A BERTWave SS
Operation Manual
5 February 2010 (First Edition)
30 November 2015 (15th Edition)
Copyright © 2010-2015, ANRITSU CORPORATION.
All rights reserved. No part of this manual may be reproduced without the prior written permission of the
publisher.
The contents of this manual may be changed without prior notice.
Printed in Japan
DANGER
WARNING
CAUTION

For Safety
iii
WARNING
•ALWAYS refer to the operation manual when working near locations
at which the alert mark shown on the left is attached. If the advice in
the operation manual is not followed, there is a risk of personal injury
or reduced equipment performance. The alert mark shown on the left
may also be used with other marks and descriptions to indicate other
dangers.
•Overvoltage Category
This equipment complies with overvoltage category II defined in IEC
61010. DO NOT connect this equipment to the power supply of
overvoltage category III or IV.
•Laser radiation warning
•NEVER look directly into the cable connector on the equipment
nor into the end of a cable connected to the equipment. There is a
risk of injury if laser radiation enters the eye.
•The Laser Safety label is attached to the equipment for safety use
as indicated in "Laser Safety" later in this section.
•To ensure that the equipment is grounded, always use the supplied
3-pin power cord, and insert the plug into an outlet with a ground
terminal. If power is supplied without grounding the equipment, there
is a risk of receiving a severe or fatal electric shock or causing
damage to the internal components.
•Only qualified service personnel with a knowledge of electrical fire and
shock hazards should service this equipment. This equipment cannot
be repaired by the operator. DO NOT attempt to remove the
equipment covers or unit covers or to disassemble internal
components. There are high-voltage parts in this equipment
presenting a risk of severe injury or fatal electric shock to untrained
personnel. In addition, there is a risk of damage to precision
components.
Repair
Electric Shock

For Safety
iv
WARNING
•The performance-guarantee seal verifies the integrity of the equipment.
To ensure the continued integrity of the equipment, only Anritsu
service personnel, or service personnel of an Anritsu sales
representative, should break this seal to repair or calibrate the
equipment. Be careful not to break the seal by opening the
equipment or unit covers.If the performance-guarantee seal is
broken by you or a third party, the performance of the equipment
cannot be guaranteed.
•This equipment should always be positioned in the correct manner. If
the cabinet is turned on its side, etc., it will be unstable and may be
damaged if it falls over as a result of receiving a slight mechanical
shock.
Always set up the equipment in a position where the power switch
can be reached without difficulty.
•When replacing the battery, use the specified battery and insert it
with the correct polarity. If the wrong battery is used, or if the battery
is inserted with reversed polarity, there is a risk of explosion causing
severe injury or death.
•DO NOT short the battery terminals and never attempt to disassemble
the battery or dispose of it in a fire. If the battery is damaged by any of
these actions, the battery fluid may leak. This fluid is poisonous.
DO NOT touch the battery fluid, ingest it, or get in your eyes. If it is
accidentally ingested, spit it out immediately, rinse your mouth with
water and seek medical help. If it enters your eyes accidentally, do
not rub your eyes, rinse them with clean running water and seek
medical help. If the liquid gets on your skin or clothes, wash it off
carefully and thoroughly.
•DO NOT expose batteries to heat or fire. Do not expose batteries to
fire. This is dangerous and can result in explosions or fire. Heating
batteries may cause them to leak or explode.
Falling Over
Calibration
Replacing Battery
Battery Fluid
Battery Disposal

For Safety
v
WARNING
•This equipment uses a Liquid Crystal Display (LCD). DO NOT subject
the equipment to excessive force or drop it. If the LCD is subjected to
strong mechanical shock, it may break and liquid may leak.
This liquid is very caustic and poisonous.
DO NOT touch it, ingest it, or get in your eyes. If it is ingested
accidentally, spit it out immediately, rinse your mouth with water and
seek medical help. If it enters your eyes accidentally, do not rub your
eyes, rinse them with clean running water and seek medical help. If
the liquid gets on your skin or clothes, wash it off carefully and
thoroughly.
LCD

For Safety
vi
CAUTION
•Always remove the main power cable from the power outlet before
cleaning dust around the power supply and fan.
•Clean the power inlet regularly. If dust accumulates around the
power pins, there is a risk of fire.
•Keep the cooling fan clean so that the ventilation holes are not
obstructed. If the ventilation is obstructed, the cabinet may
overheat and catch fire.
•Never input a signal of more than the indicated value between the
measured terminal and ground. Input of an excessive signal may
damage the equipment.
Cleaning
Check Terminal

For Safety
vii
Class 1 indicates the danger degree of the laser radiation specified
below according to IEC 60825-1:2007.
Class 1: Lasers that are safe under reasonably foreseeable conditions
of operation, including the use of optical instruments for
intrabeam viewing.
Class I indicates the degree of danger of the laser radiation outlined
below as defined by 21 CFR 1040.10:1995.
Class I: Class I levels of laser radiation are not considered to be
hazardous.
WARNING
The laser in this equipment is classified as Class 1 according to the IEC
60825-1:2007 standard, or as Class I according to the 21 CFR
1040.10:1995 standard.
CAUTION
Use of controls or adjustments or performance of procedures other than
those specified herein may result in hazardous radiation exposure.
The use of optical instruments with this product will increase eye
hazard.
Laser Safety

For Safety
viii
The model names of “recommended SFP/XFP” written on label are
listed in following table.
Table 1 Laser Safety Classifications Based on IEC 60825-1:2007
Model Name Class
Max. Optical
Output Power
(mW)*
Pulse Width (s)/
Repetition Rate
Emitted
Wavelength
(nm)
Beam
Radiation
Angle
[deg.]
Laser
Aperture
G0174A 1 0.78 CW 850 23.0 Figure 2 [1]
G0194A 1 0.8 CW 1310 11.5 Figure 2 [1]
G0195A 1 1.58 CW 1550 11.5 Figure 2 [1]
G0238A 1 0.8 CW 850 23.0 Figure 2 [1]
G0239A 1 1.12 CW 1310 11.5 Figure 2 [1]
*: Indicates the possible optical output power when each and every
reasonably foreseeable single-fault condition is included.
Table 2 Specifications of Laser Built into MP2100A/MP2101A
Model Name
Max. Optical
Output Power
(mW)*
Pulse Width (s)/
Repetition Rate
Emitted
Wavelength
(nm)
Beam
Radiation
Angle
[deg.]
G0174A 0.78 CW 850 23.0
G0194A 0.8 CW 1310 11.5
G0195A 1.58 CW 1550 11.5
G0238A 0.8 CW 850 23.0
G0239A 1.12 CW 1310 11.5
*: Indicates the possible optical output power when each and every
reasonably foreseeable single-fault condition is included.
Laser Safety

For Safety
ix
Table3 Labels on Product
Type Label Affixed to: Model Name
1 Explanation Figure 1, A
MP2100A +
MP2100A-050,
MP2100A +
MP2100A-051,
MP2101A +
MP2101A-050,
MP2101A +
MP2101A-051
2 Certification Figure 1, B
MP2100A +
MP2100A-050,
MP2100A +
MP2100A-051,
MP2101A +
MP2101A-050,
MP2101A +
MP2101A-051
3 Identification Figure 1, C
MP2100A +
MP2100A-050,
MP2100A +
MP2100A-051,
MP2101A +
MP2101A-050,
MP2101A +
MP2101A-051

For Safety
x
Laser Radiation Markings
Figure 1 Locations of Affixed Labels
Figure 2 Locations of Laser Beam Apertures