Anritsu MS2690A User manual

Document No.: M-W2855AE-52.0
ANRITSU CORPORATION
•
For safety and warning information, please read this
manual before attempting to use the equipment.
•
Additional safety and warning information is provided
within the MS2690A/MS2691A/MS2692A Signal
Analyzer Operation Manual (Mainframe Operation),
MS2830A Signal Analyzer Operation Manual
(Mainframe Operation), MS2840A Signal Analyzer
Operation Manual (Mainframe Operation), or MS2850A
Signal Analyzer Operation Manual (Mainframe
Operation). Please also refer to this document before
using the equipment.
•Keep this manual with the equipment.
MS2690A/MS2691A/MS2692A
and
MS2830A/MS2840A/MS2850A
Signal Analyzer
Operation Manual
Spectrum Analyzer Function
Remote Control
52nd Edition

ii
Safety Symbols
To prevent the risk of personal injury or loss related to equipment malfunction, Anritsu Corporation uses the
following safety symbols to indicate safety-related information. Ensure that you clearly understand the meanings of
the symbols BEFORE using the equipment. Some or all of the following symbols may be used on all Anritsu
equipment. In addition, there may be other labels attached to products that are not shown in the diagrams in this
manual.
Symbols used in manual
This indicates a very dangerous procedure that could result in serious injury or
death if not performed properly.
This indicates a hazardous procedure that could result in serious injury or death if
not performed properly.
This indicates a hazardous procedure or danger that could result in light-to-severe
injury, or loss related to equipment malfunction, if proper precautions are not taken.
Safety Symbols Used on Equipment and in Manual
The following safety symbols are used inside or on the equipment near operation locations to provide information
about safety items and operation precautions. Ensure that you clearly understand the meanings of the symbols and
take the necessary precautions BEFORE using the equipment.
This indicates a prohibited operation. The prohibited operation is indicated
symbolically in or near the barred circle.
This indicates an obligatory safety precaution. The obligatory operation is
indicated symbolically in or near the circle.
This indicates a warning or caution. The contents are indicated symbolically in or
near the triangle.
This indicates a note. The contents are described in the box.
These indicate that the marked part should be recycled.
MS2690A/MS2691A/MS2692A and MS2830A/MS2840A/MS2850A
Signal Analyzer
Operation Manual Spectrum Analyzer Function Remote Control
19 April 2007 (First Edition)
30 October 2017 (52nd Edition)
Copyright © 2007-2017, ANRITSU CORPORATION.
All rights reserved. No part of this manual may be reproduced without the prior written permission of the
publisher.
The contents of this manual may be changed without prior notice.
Printed in Japan
DANGER
WARNING
CAUTION

iii
Notes On Export Management
This product and its manuals may require an Export License/Approval by
the Government of the product's country of origin for re-
export from your
country.
Before re-
exporting the product or manuals, please contact us to confirm
whether they are export-controlled items or not.
When you dispose of export-controlled items, the products/manuals nee
d
to be broken/shredded so as not to be unlawfully used for military purpose.

iv

I
About This Manual
 Operation manual configuration
The operation manual configuration of the MS2690A/MS2691A/MS2692A,
MS2830A, MS2840A, and MS2850A Signal Analyzer is shown below.
MS2690A/MS2691A/MS2692A and MS2830A/MS2840A/MS2850A
Signal Analyzer Operation Manual (Phase Noise Measurement Function Operation)
MS2690A/MS2691A/MS2692A and MS2830A/MS2840A/MS2850A
Signal Analyzer Operation Manual (Phase Noise Measurement Function Remote Control)
MS2690A/MS2691A/MS2692A
Signal Analyzer Operation Manual
(Signal Analyzer Function Operation)
MS2690A/MS2691A/MS2692A and MS2830A/MS2840A/MS2850A
Signal Analyzer Operation Manual (Signal Analyzer Function Remote Control)
MS2830A/MS2840A/MS2850A
Signal Analyzer Operation Manual
(Signal Analyzer Function Operation)
Or
MS2690A/MS2691A/MS2692A
Spectrum Analyzer Operation Manual
(Spectrum Analyzer Function Operation)
MS2690A/MS2691A/MS2692A and MS2830A/MS2840A/MS2850A
Signal Analyzer Operation Manual (Spectrum Analyzer Function Remote Control)
MS2830A/MS2840A/MS2850A
Spectrum Analyzer Operation Manual
(Spectrum Analyzer Function Operation)
Or
MS2690A/MS2691A/MS2692A Signal Analyzer Operation Manual
(
Main Frame O
p
eration
)
MS2690A/MS2691A/MS2692A and MS2830A/MS2840A/MS2850A
Signal Analyzer Operation Manual (Main Frame Remote Control)
MS2840A Signal Analyzer Operation Manual (Main Frame Operation)
Or
MS2830A Signal Analyzer Operation Manual (Main Frame Operation)
MS2850A Signal Analyzer Operation Manual (Main Frame Operation)

II
 Signal Analyzer Operation Manual (Mainframe Operation)
 Signal Analyzer Operation Manual (Mainframe Remote Control)
Description of basic operations, maintenance procedures, common
functions and common remote functions of the mainframe
 Signal Analyzer Operation Manual (Signal Analyzer Function)
 Signal Analyzer Operation Manual (Signal Analyzer Function Remote
Control)
Description of basic operations, functions and remote functions of the
signal analyzer
 Signal Analyzer Operation Manual (Spectrum Analyzer Function)
 Signal Analyzer Operation Manual (Spectrum Analyzer Function Remote
Control) <This document>
Description of basic operations, functions and remote functions of the
spectrum analyzer
 Signal Analyzer Operation Manual (Phase Noise Measurement Function)
 Signal Analyzer Operation Manual (Phase Noise Measurement Function
Remote Control)
Description of basic operations, functions and remote functions of the
Phase Noise
Convention Used in This Manual
Except where there is a good reason to do otherwise, this manual
assumes the use of MS269xA.
Note that the descriptions in this manual also apply to MS2830A,
MS2840A, or MS2850A.

A
b
C
h
C
h
C
h
b
out Thi
s
O
h
apter 1
1.1 Ov
e
S
h
apter 2
Fr
e
2.1
Le
v
2.2
RB
2.3
Ma
2.4
Sig
2.5
Tr
a
2.6
Sw
2.7
Me
2.8
A
C 2.9
Bu
r
2.10
Ch
a
2.11
O
B
2.12
Sp
e
2.13
Sp
u
2.14
Se
t
2.15
Int
e
2.16
Co
n
2.17
Ot
h
2.18
Q
U
2.19
O
P
2.20
Se
t
2.21
Se
t
2.22
Se
t
2.23
h
apter 3
N
3.1 IE
E
3.2
A
p
p
3.3 Fr
e
3.4 Le
v
3.5 RB
3.6 Ma
Ta
b
s
Manua
l
O
vervie
w
e
rview .........
S
CPI De
v
e
quency/Sp
a
v
el ...............
W/VBW ......
a
rker .............
g
nal Search..
a
ce ...............
w
eep/Trigger
/
e
asure Funct
C
P ................
r
st Average
P
a
nnel Powe
r
B
W ...............
e
ctrum Emi
s
u
rious Emis
s
t
ting the TOI
e
rnal Signal
nfiguring Ba
t
h
er Settings .
U
EStionable
S
P
ERation St
a
t
ting Extern
a
t
ting Save o
n
t
ting Noise
F
N
ative D
E
E488.2 Co
m
p
lication Co
m
e
quency/Sp
a
v
el Settings .
W/VBW Set
t
a
rker Setting
s
b
le of
C
l
.............
.
w
...........
.
...................
v
ice Me
s
a
n ................
...................
...................
...................
...................
...................
/
Gate ...........
ion ..............
...................
P
ower .........
r
..................
...................
s
sion Mask ..
s
ion Measur
e
Measurem
e
G
enerator
C
t
ch Measure
...................
S
tatus Regi
s
a
tus Registe
r
a
l Mixer ........
n
Event .......
F
loor Reducti
evice M
e
m
mon Devic
e
m
mon Devic
e
a
n Settings ..
...................
t
ings ...........
s
..................
C
onten
t
.
.............
.
.
.............
.
.
...................
s
sage D
e
.
...................
.
...................
.
...................
.
...................
.
...................
.
...................
.
...................
.
...................
.
...................
.
...................
.
...................
.
...................
.
...................
e
ment Funct
i
e
nt Function
s
ontrol functi
o
ment Settin
g
.
...................
s
ter ..............
...................
.
...................
.
...................
on ...............
e
ssage
L
e
Messages
e
Messages
.
...................
.
...................
.
...................
.
...................
t
s
..............
..............
...................
e
tails .....
...................
...................
...................
...................
...................
...................
...................
...................
...................
...................
...................
...................
...................
ion ..............
s
..................
o
n ...............
g
s ................
...................
...................
...................
...................
.................
2
.................
2
L
ist ........
...................
...................
...................
...................
...................
...................
II
I
........ I
.... 1-1
.... 1-2
.... 2-1
.. 2-31
.. 2-54
.. 2-76
2-103
2-166
2-186
2-250
2-323
2-350
2-446
2-479
2-529
2-576
2-712
2-823
2-852
2-859
2-952
2-965
2-980
2-989
2
-1010
2
-1017
.... 3-1
.... 3-3
.... 3-5
.... 3-7
.... 3-8
.... 3-9
.. 3-10
1
I
2
3
4

IV.
C
h
3.7 Sig
3.8 Tr
a
3.9 Sw
3.10 Me
3.11 Ba
t
3.12 Re
f
3.13 Ot
h
3.14 Se
t
N
h
apter 4
g
nal Search
S
a
ce Settings .
w
eep/Trigger
/
e
asure Funct
t
ch Measure
f
erence Sig
n
h
er Settings .
t
ting Extern
a
N
ative D
S
ettings ......
...................
/
Gate Settin
g
ion Settings
Function S
e
n
al Settings .
...................
a
l Mixer ........
evice M
e
.
...................
.
...................
g
s .................
.
...................
e
ttings ..........
.
...................
.
...................
.
...................
e
ssage
D
...................
...................
...................
...................
...................
...................
...................
...................
D
etails ...
.. 3-13
.. 3-15
.. 3-18
.. 3-23
.. 3-52
.. 3-54
.. 3-55
.. 3-56
.... 4-1

1-1
1
Overview
Overview
Chapter 1
This chapter provides an overview of the remote control of the Spectrum
Analyzer function (hereinafter, referred to as “this application”).
1.1 Overview ....................................................................... 1-2

Chapter 1 Overview
1-2.
1.1 Overview
Automatic measurement can be performed by using this instrument in
connection with an external controller (PC). This instrument is standard
equipped with GPIB, Ethernet, and USB interfaces. You can also select a
remote control command from the SCPI mode, which is a command
format defined by the SCPI Consortium, and Native mode, which is our
unique format.
See the
MS2690A/MS2691A/MS2692A and
MS2830A/MS2840A/MS2850A Signal Analyzer Operation Manual
(Mainframe Remote Control)
for how to switch the language mode.
You can use the Native mode by converting SCPI commands into Native
ones. See the
MS2690A/MS2691A/MS2692A and
MS2830A/MS2840A/MS2850A Signal Analyzer Operation Manual
(Mainframe Remote Control)
for details.