ANTAIRA LNP-C500G-T User manual

Antaira Technologies
LNP-C500G Series User Manual V1.0
i
LNP-C500G Series
Compact 5-Port Industrial Gigabit PoE+ Unmanaged Ethernet
Switch, w/4*10/100/1000Tx (PSE: 30W/Port) + 1*10/100/1000Tx
Version 1.0
(October 2017)
User Manual

Antaira Technologies
LNP-C500G Series User Manual V1.0
ii
© Copyright 2017 Antaira Technologies, LLC.
All Rights Reserved
This document contains information which is protected by copyright. Reproduction, adaptation or translation
without prior permission is prohibited, except as allowed under the copyright laws.
Trademark Information
Antaira is a registered trademark of Antaira Technologies, LLC. Microsoft Windows and the Windows logo are the
trademarks of Microsoft Corp. All other brand and product names are trademarks or registered trademarks of
their respective owners.
Disclaimer
Antaira Technologies, LLC. provides this manual without warranty of any kind, expressed or implied, including but
not limited to the implied warranties of merchantability and fitness for a particular purpose. Antaira Technologies,
LLC. may make improvements and/or changes to the product and/or specifications of the product described in
this manual, without prior notice. Antaira Technologies, LLC. will not be liable for any technical inaccuracies or
typographical errors found in this guide. Changes are periodically made to the information contained herein and
will be incorporated into later versions of the manual. The information contained is subject to change without prior
notice.

Antaira Technologies
LNP-C500G Series User Manual V1.0
iii
FCC Notice
This equipment has been tested and found to comply with the limits for a Class-A digital device, pursuant to Part
15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy. It may cause
harmful interference to radio communications if the equipment is not installed and used in accordance with the
instructions. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
 Reorient or relocate the receiving antenna.
 Increase the separation between the equipment and receiver.
 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
 Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications not expressly approved by the grantee of this device could void the user's
authority to operate the equipment.
CE Mark Warning
This is a Class-A product. In a domestic environment, this product may cause radio interference in which case
the user may be required to take adequate measures.
Industrial Ethernet Switch
User Manual
This manual supports the following models:
 LNP-C500G
 LNP-C500G-T
Please check our website (www.antaira.com) for any updated manual or contact us by e-mail
([email protected]).

Antaira Technologies
LNP-C500G Series User Manual V1.0
ii
Table of Contents
1. Overview ............................................................... 1
1.1 Key Features ...................................................... 1
1.2 Package Contents .............................................. 1
1.3 Safety Precaution ............................................... 1
2. Hardware Description .......................................... 2
2.1 Physical Dimensions .......................................... 2
2.2 Front Panel ........................................................ 3
2.3 Top View ............................................................ 3
2.4 LED Indicators ................................................... 4
2.5 Ethernet Ports .................................................... 4
2.6 Cabling ............................................................... 5
2.7 Wiring the Power Inputs ..................................... 5
3. Mounting Installation ........................................... 7
3.1 DIN-Rail Mounting .............................................. 7
3.2 Wall Mounting .................................................... 9
4. Hardware Installation ................................................ 10
4.1 Installation Steps .............................................. 10
5. Network Application ................................................. 11
6. Trouble Shooting ...................................................... 12
7. Technical Specifications .......................................... 13

Antaira Technologies
LNP-C500G Series User Manual V1.0
1
1. Overview
Antaira Technologies’ LNP-C500G series is a compact 5-port industrial gigabit PoE+ unmanaged
Ethernet switch. The small form factor of this metal IP30 rated design is 50% smaller which allows
for a more versatile implementation. The LNP-C500G series is equipped with 4*10/100/1000Tx
Ethernet ports that support IEEE 802.3af/at for a maximum of 30W/port and 1*10/100/1000Tx
Ethernet port. The LNP-C500G series can handle high bandwidth applications in tight spaces.
The LNP-C500G series supports high EFT & ESD protection through the redundant power inputs
that support reverse polarity and overload current protection. This product series supports DIN-rail
as well as wall mountable orientations and provides operating temperature range models in STD:
-10°C to 70°C and EOT: -40°C to 75°C. This is an industrial grade unit applicable for networking
applications in factory automation, ITS, power/utility, water wastewater treatment plants, or any
application that needs a compact solution.
1.1 Key Features
 System Interface/Performance
 RJ-45 ports support the auto MDI function
 Embedded 4*10/100/1000Tx (PSE 30W/port) and 1*100/1000Tx port
 Store-and-forward switching architecture
 Power Input
 DC 48~55V redundant power with a 4-pin removal terminal block
 Operating Temperature
 Standard operating temperature model: -10°C ~ 70°C
 Extended operating temperature model (–T): -40°C ~ 75°C
 Case/Installation
 IP30 protection
 DIN-Rail and wall mount design
1.2 Package Contents
 1 - Quick Installation Guide
 1 - LNP-C500G Industrial PoE+ Gigabit Unmanaged Ethernet Switch
 1 - Wall mounting bracket set with screws
 1 - DC cable - 18 AWG & DC jack 5.5x2.1mm
1.3 Safety Precaution
Attention: If the DC voltage is supplied by an external circuit, please use a protection device on
the power supply input. The industrial Ethernet switch’s hardware specs, ports,
cabling information, and wiring installation will be described within this user manual.

Antaira Technologies
LNP-C500G Series User Manual V1.0
2
2. Hardware Description
2.1 Physical Dimensions
Figure 2.1, below, shows the physical dimensions of Antaira Technologies’ LNP-C500G series:
(W x H x D) is 30mm x 95mm x 75mm
Figure 2.1
Physical Dimensions

Antaira Technologies
LNP-C500G Series User Manual V1.0
3
2.2 Front Panel
The front panel of the LNP-C500G series can be seen below (Figure 2.2).
2.3 Top View
Figure 2.3, below, shows the top panel of the LNP-C500G series that is equipped with one 4-pin
removal terminal block connector for dual DC power inputs (48~55VDC).
Figure 2.2
Front Panel
Figure 2.3
Top Panel View
Grounding Screw
4-Pin Removal Terminal Block (Power Input)
LED for Power
LAN# 1~5 – LED for 1000Mbps
LAN# 1~4 – 10/100/1000Tx RJ45 w/ PoE+
LAN# 1~5 – LED for 10/100Mbps
LAN# 5 – 10/100/1000Tx RJ45
LED for PoE

Antaira Technologies
LNP-C500G Series User Manual V1.0
4
2.4 LED Indicators
There are LED light indicators located on the front panel that displays the power and network
status. Each LED indicator has a different color and has its own specific meaning, see below in
Table 2.1.
LED Color Description
Power
Green On Power input 1 or 2 is active
Off Power input 1 and 2 are inactive
PoE 1-4 Green On The port is supplying power to the powered-device
Off No powered-device attached or power supply fails
LAN Port
1 ~ 5
Green
On Connected to network, 1000Mbps
Flashing Networking is active
Off Not connected to network
Green
On Connected to network, 10/100Mbps
Flashing Networking is active
Off Not connected to network
2.5 Ethernet Ports

RJ-45 Ports
RJ-45 Ports (Auto MDI/MDIX): The RJ-45 port is auto-sensing for 10/100Base-Tx or 1000Base-Tx
device connections. Auto MDI/MDIX means that the switch can connect to another switch or
workstation without changing the straight-through or crossover cabling. See the figures shown
below for the straight-through and crossover cabling schematics.
Figure 2.4: RJ-45 Ethernet Port Pin
Table 2.1
LED Indicators

Antaira Technologies
LNP-C500G Series User Manual V1.0
5
2.6 Cabling
 Twisted-pair segments can be connected with an Unshielded Twisted Pair (UTP) or Shielded
Twisted Pair (STP) cable. The cable between the equipment and the link partner (media
converter, switch, hub, workstation, etc.) must be less than 100 meters (328 ft.) long.
2.7 Wiring the Power Inputs
Please follow the steps below to insert the power wire.
1. Insert the positive and negative wires into the PWR1 (V1+, V1-) and PWR2 (V2+, V2-) contacts
on the terminal block connector as shown below in Figure 2.7.
Figure 2.7
Power Terminal Block
Figure 2.5 Figure 2.6
Straight-Through Cables Schematic Crossover Cables Schematic

Antaira Technologies
LNP-C500G Series User Manual V1.0
6
2. Tighten the wire-clamp screws to prevent the wires from loosening, as shown below in Figure
2.8.
**Note:  Only use copper conductors, 60/75°C, tighten to 5 lbs.
 The wire gauge for the terminal block should range between 18~20 AWG.
Figure 2.8
Power Terminal Block