ANTAIRA LNP-1204GN-T User manual

LNP-1204GN-T User’s Manual
Antaira Technologies
1
12-port Managed Gigabit Industrial Ethernet
Switch with 8 x Gigabit Combo Ports and
4 x 1000BaseX SFP Ports
User’s Manual
Version 1.2

LNP-1204GN-T User’s Manual
Antaira Technologies
2
COPYRIGHT NOTICE
Copyright © 2013 Antaira Technologies.
All rights reserved.
No part of this publication may be reproduced in any form without the prior written consent of
Antaira Technologies.
TRADEMARKS
The trademark is a registered trademark of Antaira Technologies.
All other trademarks belong to their respective owners.
REGULATORY COMPLIANCE STATEMENT
Product(s) associated with this publication complies/comply with all applicable regulations.
Please refer to the Technical Specifications section for more details.
WARRANTY
Antaira warrants that all Antaira products are free from defects in material and workmanship
for a specified warranty period from the invoice date (5 years for most products). Antaira will
repair or replace products found by Antaira to be defective within this warranty period, with
shipment expenses apportioned by Antaira and the distributor. This warranty does not cover
product modifications or repairs done by persons other than Antaira-approved personnel,
and this warranty does not apply to Antaira products that are misused, abused, improperly
installed, or damaged by accidents.
Please refer to the Technical Specifications section for the actual warranty period(s) of the
product(s) associated with this publication.
DISCLAIMER
Information in this publication is intended to be accurate. Antaira shall not be responsible for
its use or infringements on third-parties as a result of its use. There may occasionally be
unintentional errors on this publication. Antaira reserves the right to revise the contents of
this publication without notice.

LNP-1204GN-T User’s Manual
Antaira Technologies
3
Table of Contents
Getting to Know Your Switch........................................................................6
1.1 About the LNP-1204GN-T Industrial Switch............................................................. 6
1.2 Software Features.................................................................................................... 6
1.3 Hardware Features................................................................................................... 7
Hardware Installation.....................................................................................8
2.1 Installation Switch on DIN-Rail................................................................................. 8
2.1.1 Mount Series on DIN-Rail.................................................................................... 8
2.2 Wall Mounting Installation ........................................................................................ 9
2.2.1 Mount LNP-1204GN-T on wall........................................................................... 10
Hardware Overview......................................................................................12
3.1 Front Panel............................................................................................................. 12
3.2 Front Panel LEDs................................................................................................... 13
3.3 Top View Panel....................................................................................................... 14
3.4 Rear Panel ............................................................................................................. 15
Cables...........................................................................................................16
4.1 Ethernet Cables...................................................................................................... 16
4.1.1 100BASE-TX/10BASE-T Pin Assignments........................................................ 16
4.2 SFP......................................................................................................................... 18
4.3 Console Cable........................................................................................................ 18
WEB Management........................................................................................19
5.1 Configuration by Web Browser .............................................................................. 19
5.1.1 About Web-based Management........................................................................ 19
5.1.2 Basic Setting...................................................................................................... 21
5.1.2.1 System Information......................................................................................... 21
5.1.2.2 Admin & Password ......................................................................................... 22
5.1.2.3 IP Setting........................................................................................................ 23
5.1.2.4 HTTPS............................................................................................................ 24
5.1.2.5 SSH ................................................................................................................ 25
5.1.2.6 LLDP............................................................................................................... 25
5.1.2.7 Backup/Restore Configuration ....................................................................... 30
5.1.2.8 Firmware Update............................................................................................ 31
5.1.3 DHCP Server ..................................................................................................... 31

LNP-1204GN-T User’s Manual
Antaira Technologies
4
5.1.3.1 Setting ...................................................................................................... 31
5.1.3.2 DHCP Dynamic Client List...................................................................... 32
5.1.3.3 DHCP Client List...................................................................................... 32
5.1.4 Port Setting ........................................................................................................ 33
5.1.4.1 Port Control ............................................................................................. 33
5.1.4.2 Rate Limit................................................................................................. 34
5.1.4.3 Port Trunk ................................................................................................ 35
5.1.4.4 Port Trunk ................................................................................................ 41
5.1.5 Redundancy....................................................................................................... 42
5.1.5.1 Ring .......................................................................................................... 42
5.1.5.2 MSTP ........................................................................................................ 43
5.1.6 VLAN.................................................................................................................. 52
5.1.6.1 VLAN Membership Configuration.......................................................... 52
5.1.6.2 Private VLAN............................................................................................ 64
5.1.7 SNMP................................................................................................................. 65
5.1.7.1 SNMP-System.......................................................................................... 65
5.1.7.2 SNMP-Communities................................................................................ 68
5.1.7.3 SNMP-Users............................................................................................. 69
5.1.7.4 SNMP-Groups.......................................................................................... 70
5.1.7.5 SNMP-Views............................................................................................. 71
5.1.7.6 SNMP-Accesses...................................................................................... 72
5.1.8 Traffic Prioritization ............................................................................................ 73
5.1.8.1 Port Configuration................................................................................... 73
5.1.8.2 QoS Control List...................................................................................... 74
5.1.8.3 Storm Control .......................................................................................... 76
5.1.8.4 Wizard....................................................................................................... 77
5.1.9 IGMP Snooping.................................................................................................. 78
5.1.9.1 IGMP Snooping........................................................................................ 78
5.1.9.2 IGMP Snooping Status............................................................................ 79
5.1.10 Security.......................................................................................................... 80
5.1.10.1 ACL ........................................................................................................... 80
5.1.10.2 802.1x ....................................................................................................... 81
5.1.11 Warning.......................................................................................................... 84
5.1.11.1 Fault Alarm............................................................................................... 84
5.1.11.2 System Warning ...................................................................................... 85
5.1.11.2.1 Syslog Setting ...................................................................................... 85
5.1.11.2.2 Syslog Event......................................................................................... 85

LNP-1204GN-T User’s Manual
Antaira Technologies
5
5.1.12 Monitor and Diagnostics................................................................................ 86
5.1.12.1 MAC Table ................................................................................................ 86
5.1.12.2 Port Statistic ............................................................................................ 88
5.1.12.2.1 Traffic Overview ................................................................................... 88
5.1.12.2.2 Detailed Statistics ................................................................................ 89
5.1.12.3 Port Mirroring .......................................................................................... 91
5.1.12.4 System Log.............................................................................................. 92
5.1.12.5 Cable Diagonstics................................................................................... 94
5.1.12.6 Ping........................................................................................................... 95
5.1.13 Power over Ethernet (P.O.E.)........................................................................ 96
5.1.13.1 PoE Configuration - Reserved Power determined............................... 96
5.1.13.2 PoE Configuration - Power management Mode................................... 97
5.1.13.3 PoE Configuration - Primary/backup Power Supply ........................... 97
5.1.13.4 PoE Configuration - Port Configuration ............................................... 98
5.1.13.5 Power over Ethernet Status ................................................................... 99
5.1.13.6 LLDP Power Over Ethernet Neighbor ................................................. 100
Command Line Interface Management....................................................103
6.1 About CLI Management................................................................................... 103

LNP-1204GN-T User’s Manual
Antaira Technologies
6
Getting to Know Your Switch
1.1 About the LNP-1204GN-T Industrial Switch
The LNP-1204GN-T is powerful full Gigabit managed industrial switch which have many
features. The switch can work under wide temperature, dusty environment and humid
condition. They can be managed by Windows Utility, WEB, TELNET and Console or other
third-party SNMP software as well.
1.2 Software Features
World’s fastest Gigabit Redundant Ethernet Ring (Recovery time < 20ms over 250 units
connection)
Supports Ring Coupling, Dual Homing, RSTP
Supports SNMPv1/v2c/v3 & RMON & Port base/802.1Q VLAN Network Management
Event notification by Email, SNMP trap and Relay Output
Windows Utility, Web-based ,Telnet and Console (CLI) configuration
Enable/disable ports, MAC based port security
Port based network access control (802.1x)
VLAN (802.1q ) to segregate and secure network traffic
Radius centralized password management
SNMPv3 encrypted authentication and access security
RSTP (802.1w)
Quality of Service (802.1p) for real-time traffic
VLAN (802.1q) with double tagging and GVRP supported
IGMP Snooping for multicast filtering
Port configuration, status, statistics, mirroring, security
Remote Monitoring (RMON)

LNP-1204GN-T User’s Manual
Antaira Technologies
7
1.3 Hardware Features
Dual DC power inputs for power redundancy
Operating Temperature: -40 to 70oC
Storage Temperature: -40 to 85oC
Operating Humidity: 5% to 95%, non-condensing
Casing: IP-30
8 x 10/100/1000Base –T(X)
4 x 1000 Base-X SFP
Console Port
Dimensions 96.4 (W) x 108.5 (D) x 154 (H) mm (3.8 x 4.2.7 x 6.06 inch)

LNP-1204GN-T User’s Manual
Antaira Technologies
8
Hardware Installation
2.1 Installation Switch on DIN-Rail
Each switch has a Din-Rail kit on rear panel. The Din-Rail kit helps switch to fix on the
Din-Rail. It is easy to install the switch on the Din-Rail:
2.1.1 Mount Series on DIN-Rail
Step 1: Slant the switch and mount the metal spring to Din-Rail.
Metal Spring

LNP-1204GN-T User’s Manual
Antaira Technologies
9
Step 2: Push the switch toward the Din-Rail until you heard a “click” sound.
2.2 Wall Mounting Installation
Each switch has another installation method for users to fix the switch. A wall mount
panel can be found in the package. The following steps show how to mount the switch on
the wall:

LNP-1204GN-T User’s Manual
Antaira Technologies
10
2.2.1 Mount LNP-1204GN-T on wall
Step 1: Remove Din-Rail kit.
Step 2: Use 6 screws that can be found in the package to combine the wall mount panel.
Just like the picture shows below:

LNP-1204GN-T User’s Manual
Antaira Technologies
11
The screws specification shows in the following two pictures. In order to prevent switches
from any damage, the screws should not larger than the size that used in LNP-1204GN-T
switch.
Pozidrive

LNP-1204GN-T User’s Manual
Antaira Technologies
12
Hardware Overview
3.1 Front Panel
The following table describes the labels that stick on the LNP-1204GN-T
Port Description
SFP ports 4 1000BaseX on SFP port
RJ45 Port
8 10/100/1000Base-T(X) P.S.E.
Console Use RS-232 with RJ-45 connecter to manage switch.
LNP-1204GN-T
1. Reset button. Push the button 3 seconds for reset; 5 seconds for factory default.
2. LED for PWR.When the PWR UP, the green led will be light on
3. LED for PWR1
4. LED for PWR2
5. LED for R.M (Ring master). When the LED light on, it means that the switch is the ring
master of Ring. LED for Ring. When the led light on, it means the Ring is activated.
6. LED for Ring. When the led light on, it means the Ring is activated.
7. LED for Fault. When the light on, it means Power failure or Port down/fail.
8. Console port (RJ-45)

LNP-1204GN-T User’s Manual
Antaira Technologies
13
9. P.O.E LED
10. LED for Ethernet ports link status.
11. 10/100/1000Base-T(X) ports
12. 1000 Base-X SFP ports
13. LED for SFP ports link status.
3.2 Front Panel LEDs
LED Color Status Description
PWRGreen On DC power module up
PW1 Green On DC power module 1activated.
PW2Green On DC Power module 2activated.
R.M Green On Ring ring Master.
Ring Green
On Ring enabled.
Slowly blinking Ring has only One link. (lack
of one link to build the ring.)
Fast blinking Ring work normally.
Fault Amber On Fault relay. Power failure or
Port down/fail.
Gigabit Ethernet ports
LNK/ACT Green Blinking Data transmitted.
On Port link up.
Gigabit SFP ports
LNK/ACT Green Blinking Data transmitted.
On Port link up.
PoE indicator LED
Indicator Green Off PoE output disable
On PoE output enable

LNP-1204GN-T User’s Manual
Antaira Technologies
14
3.3 Top View Panel
The bottom panel component of LNP-1204GN-T is showed as below:
1. Terminal block includes: PWR1, PWR2 (50-57V DC)
2. Ground wired
.

LNP-1204GN-T User’s Manual
Antaira Technologies
15
3.4 Rear Panel
The rear panel components of LNP-1204GN-T are showed as below:
1. Screw holes for wall mount kit.
2. Din-Rail kit

LNP-1204GN-T User’s Manual
Antaira Technologies
16
Cables
4.1 Ethernet Cables
The LNP-1204GN-T switch has standard Ethernet ports. According to the link type, the
switch use CAT 3, 4, 5,5e UTP cables to connect to any other network device (PCs, servers,
switches, routers, or hubs). Please refer to the following table for cable specifications.
Cable Types and Specifications
Cable Type Max. Length Connector
10BASE-T Cat. 3, 4, 5 100-ohm UTP 100 m (328 ft) RJ-45
100BASE-TX Cat. 5 100-ohm UTP UTP 100 m (328 ft) RJ-45
1000BASE-TX Cat. 5/Cat. 5e 100-ohm
UTP UTP 100 m (328ft) RJ-45
4.1.1 100BASE-TX/10BASE-T Pin Assignments
With 100BASE-TX/10BASE-T cable, pins 1 and 2 are used for transmitting data, and
pins 3 and 6 are used for receiving data.
10/100 P.S.E. Base-TX RJ-45 Pin Assignments (TYPE A)
Pin Number Assignment
1 P.O.E Power input +
2 P.O.E Power input +
3 P.O.E Power input -
4 Not used
5 Not used
6 P.O.E Power input -
7 Not used
8 Not used

LNP-1204GN-T User’s Manual
Antaira Technologies
17
1000 Base-T RJ-45 Pin Assignments
Pin Number Assignment
1 BI_DA+
2 BI_DA-
3 BI_DB+
4 BI_DC+
5 BI_DC-
6 BI_DB-
7 BI_DD+
8 BI_DD-
The LNP-1204GN-T switch supports auto MDI/MDI-X operation function. You can
use a straight-through cable to connect PC to switch. The following table below shows
the 10BASE-T/ 100BASE-TX MDI and MDI-X port pin outs.
10/100 Base-T MDI/MDI-X pins assignment
Pin Number MDI port MDI-X port
1 TD+(transmit) RD+(receive)
2 TD-(transmit) RD-(receive)
3 RD+(receive) TD+(transmit)
4 Not used Not used
5 Not used Not used
6 RD-(receive) TD-(transmit)
7 Not used Not used
8 Not used Not used
1000 Base-T MDI/MDI-X pins assignment
Pin Number MDI port MDI-X port
1 BI_DA+ BI_DB+
2 BI_DA- BI_DB-
3 BI_DB+ BI_DA+
4 BI_DC+ BI_DD+
5 BI_DC- BI_DD-
6 BI_DB- BI_DA-
7 BI_DD+ BI_DC+
8 BI_DD- BI_DC-
Note: “+” and “-” signs represent the polarity of the wires that make up each wire pair.

LNP-1204GN-T User’s Manual
Antaira Technologies
18
4.2 SFP
The Switch has fiber optical ports with SFP connectors. The fiber optical ports are in
multi-mode (0 to 550M, 850 nm with 50/125 µm, 62.5/125 µm fiber) and single-mode with LC
connector. Please remember that the TX port of Switch Ashould be connected to the RX
port of Switch B.
Switch-A Switch-B
4.3 Console Cable
LNP-1204GN-T switch can be management by console port. The DB-9 to RJ-45 cable
can be found in the package. You can connect them to PC via a RS-232 cable with DB-9
female connector and the other end (RJ-45 connector) connects to console port of switch.
PC pin out (male) assignment RS-232 with DB9 female connector DB9 to RJ 45
Pin #2 RD Pin #2 TD Pin #2
Pin #3 TD Pin #3 RD Pin #3
Pin #5 GD Pin #5 GD Pin #5
Fiber cord

LNP-1204GN-T User’s Manual
Antaira Technologies
19
WEB Management
5.1 Configuration by Web Browser
This section introduces the configuration by Web browser.
5.1.1 About Web-based Management
An embedded HTML web site resides in flash memory on the CPU board. It contains
advanced management features and allows you to manage the switch from anywhere on the
network through a standard web browser such as Microsoft Internet Explorer.
The Web-Based Management function supports Internet Explorer 5.0 or later. It is based
on Java Applets with an aim to reduce network bandwidth consumption, enhance access
speed and present an easy viewing screen.
Note: By default, IE5.0 or later version does not allow Java Applets to open sockets. You need to explicitly modify
the browser setting in order to enable Java Applets to use network ports.
Preparing for Web Management
The default value is as below:
IPAddress: 192.168.10.1
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.10.254
User Name: admin
Password: admin
System Login
1. Launch the Internet Explorer.
2. Type http:// and the IP address of the switch. Press “Enter”.

LNP-1204GN-T User’s Manual
Antaira Technologies
20
3. The login screen appears.
4. Key in the username and password. The default username and password is
“admin”.
5. Click “Enter” or ”OK” button, then the main interface of the Web-based
management appears.
Login screen
Main Interface
Main interface