ANTAIRA LNX-802AG-S10-T User manual

6 10/100/1000TX + 2G Fiber
Industrial Ethernet Switch
User Manual

FCC Warning
This Equipment has been tested and found to comply with the limits for a
Class-A digital device, pursuant to Part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy. It may cause harmful interference to radio
communications if the equipment is not installed and used in accordance
with the instructions. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
CE Mark Warning
This is a Class-A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take
adequate measures.

Content
Introduction................................................................ 1
Feature..................................................................... 1
Package Contents.................................................... 3
Hardware Description ............................................... 4
Physical Dimension.................................................. 4
Front Panel .............................................................. 5
Top View.................................................................. 5
LED Indicators ......................................................... 6
Green Ethernet ........................................................ 7
Hardware Installation ................................................ 1
Installation Steps...................................................... 1
Cabling..................................................................... 1
Wiring the Power Inputs........................................... 2
Wiring the P-Fail Alarm Contact............................... 3
DIN-Rail Mounting.................................................... 3
Wall Mount Plate Mounting...................................... 5
Network Application.................................................. 7
Troubles shooting ..................................................... 8

1
Introduction
The 6 10/100/1000TX + 2G fiber industrial switch is a cost-effective solution and meets
the high reliability requirements demanded by industrial applications. By using fiber port
can extend the connection distance that increases the network elasticity and
performance. And also support wide operation temperature and green power features.
Feature
Standard
IEEE 802.3 10Base-T Ethernet
IEEE 802.3u 100Base-TX
IEEE 802.3ab 1000Base-T
IEEE 802.3z Gigabit fiber
IEEE 802.3x Flow Control and Back Pressure
LED Indicators
Per unit: Power 1 (Green), Power 2 (Green),
P-Fail(Red), Link/Activity for Fiber (Green)
Per port: Link/Activity (Green), Speed (Green)
Connector 10/100/1000T: RJ-45 x 6
1000 Fiber: Fiber sockets(SC) x 2
Switch architecture Store and forward switch architecture
Back-plane 16Gbps

2
MAC address
8K MAC address table with Auto learning function
Power Supply
DC 12~48V, Redundant power and removable terminal
block
24VAC (18~30V)
Power Consumption
9.3 Watt (Max)
Ventilation
Fanless
Operating
Temperature
-40℃~75℃
-40℃~60℃(non-air-flow environment)
Operating Humidity
5% to 95%
Storage environment -40℃~85℃
Storage Humidity
5% to 95%
MTBF
505863 hrs
Dimensions
59.6mm (W) x 105mm (D) x 152mm (H)
EMC
■FCC Class A
■ EN61000-6-4
■ EN61000-6-2
■EN61000-4-2 (ESD)
■EN61000-4-3 (Radiated RFI)
■ EN61000-4-4 (Burst)
■ EN61000-4-5 (Surge)
■ EN61000-4-6 (Induced RFI)

3
■ EN61000-4-8 (Magnetic Field)
■ EN61000-4-11 (Voltage Dip)
■ EN61000-4-12 (Oscillatory waves)
■ EN61000-3-2 (Harmonics Current)
■ EN61000-3-3 (Voltage Fluctuation & Flickers)
Safety
■ UL508
■ Class 1 Division 2
Stability Testing
■IEC60068-2-32 (Free fall)
■IEC60068-2-27 (Shock)
■IEC60068-2-6 (Vibration)
Package Contents
Please refer to the package content list below to verify them against the checklist.
6 10/100/1000TX + 2 Gigabit fiber industrial switch
User manual
Block connector
2 wall mount plates and 6 screws
One DIN-Rail (attached on the switch)
Compare the contents of the industrial switch with the standard checklist above. If any
item is damaged or missing, please contact the local dealer for service.

4
Hardware Description
In this paragraph, it will describe the Industrial switch’s hardware spec, port, cabling
information, and wiring installation.
Physical Dimension
6 10/100/1000TX + 2G fiber industrial switch dimension (W x D x H) is 59.6mm x
105mm x 152mm

5
Front Panel
The Front Panel of the 6 10/100/1000TX +2G fiber industrial switch is shown as below:
Front Panel of the industrial switch
Top View
The top panel of the 6 10/100/1000TX + 2G fiber industrial switch has one terminal block
connector of two DC power inputs.
Top Panel of the industrial switch

6
LED Indicators
There are diagnostic LED indicators located on the front panel of the industrial switch.
They provide real-time information of system and optional status. The following table
provides description of the LED status and their meanings for the switch.
LED Status Description
Per Unit
PWR1(Green)
On
Power input 1 is active
Off
Power input 1 is inactive
BLK
--
PWR2(Green)
On
Power input 2 is active
Off Power input 2 is inactive
BLK
--
P-FAIL(Red)
On
Power1/Power2 is inactive
Off
Power1 and Power2 are both active, or no
power input
BLK
--
Link/Active for
Fiber(Green)
On
Link up
Off
Link down
BLK Transmitting
Per Port
Link/Active(Green)
On
Link up
Off
Link down
BLK
Transmitting
Speed(Green)
On
1000Mbps

7
Off
100Mbps
BLK
--
Green Ethernet
The 6 10/100/1000TX + 2G fiber industrial switch has a special function. The switch will
automatically detect Ethernet ports status and Cable Length and adjust power efficiency.
Below table shows 6 10/100/1000TX + 2G fiber industrial switch power consumption.
Link Up: Cable Length 20m
Green power (off/on) Consumption (Watts)
OFF 6.9
ON 5.85
Gap 0.34
Saving % 5.49%