Antari DarkFX Spot 510 IP User manual

DarkFX Spot 510 IP
User Manual
English
©2016 Antari Lighting and Effects Ltd.

3
User Manual –English
Safety Information
Please read the following safety information carefully before operating the fixture.
Information includes important safety information about installation, usage, and
maintenance. Pay attention to all warning labels and instructions in this manual
and printed on the fixture.
HIGH INTENSITY 365nm ULTRAVIOLET LIGHT
RISK OF EXPOSURE TO ULTRAVIOLET RADIATION
AVOID DIRECT EYE AND SKIN EXPOSURE
DO NOT OPERATE FIXTURE WITHOUT EXTERNAL COVER AND
PROTECTIVE LENS INSTALLED.
DO NOT OPERATE FIXTURE WITH DAMAGED EXTERNAL COVER AND/OR
PROTECTIVE LENS.
If you have questions about how to operate the fixture safely, please contact your local
Antari dealer for help.
․Never look directly into the light source.
․Do not connect device to dimmer pack.
․Make sure power cord is never crimped or damaged.
․This fixture is design to use with DarkFX Drive 4
․No user serviceable and modifiable parts inside. Never try to repair this product,
unauthorized repair may lead to fixture damage and or malfunction.
․Make sure there are no flammable materials close to the fixture while operating.
․If the fixture fails to work, unplug the fixture and stop operation immediately. Contact
your local Antari dealer for advise.
CAUTION

4
Unpacking and Inspection
Immediately upon receiving the fixture, carefully unpack the carton, check all content to
ensure that all parts are present and have been received in good condition. If any parts
appear damaged or mishandled from shipping, notify the shipper immediately and retrain the
packing material for inspection.
What is included: 1 x DarkFX Spot 510 IP UV Light
1 x User Manual
Product Dimension
Installation
The DarkFX Spot 510 IP fixture should be connected to DarkFX Drive 4 driver. Refer to
DarkFX Drive 4 user manual for full details of mains power requirements and DMX operation.
See below diagram for wiring:

5
DarkFX Spot 510 IP is wired to output terminal of DarkFX Drive 4. Each output terminal can
connect one DarkFX Spot 510 IP fixture.
Physical Installation
Important
․Use supplied mounting bracket or rigging clamp to install fixture.
․Make sure installation location, fastening connecting, and rigging hardware can hold at
least 10 times the weight of the fixture.
․Make sure no combustible or flammable material nearby.
․Secure each fixture with an approved safety cable that can hold at least 10 times the
weight of fixture.
․Make sure fixture installed in a well ventilated area.
․Consider lamp replacement and routine maintenance access when selecting installation
location.

6
Adjustable Mounting Bracket
Adjust mounting bracket by loosening gear screw, set the fixture to desire angle and tighten
the gear screw to finish adjustment. Illustration below demonstrates how to adjust mounting
bracket.
Mounting
Use screws for surface mounting or clamps for truss mounting.
For surface mounting
For truss mounting

7
Service and Maintenance
Important! Smoke fluid residue, dust and any excessive particle residue will
degrade product performance, cause overheating and damage fixture. Damages
caused by inadequate cleaning or maintenance are not covered by product
warranty.
Cleaning
․Unplug fixture from DarkFX Drive 4 before starting.
․Use vacuum or air compressor and soft brush to remove dust on components
and vents.
․Clean fixture with a moist, lint-free cloth.
․Never use alcohol or solvents.
Technical Specifications
Input voltage
DC20-24V
Power
12W @ 500mA
LED
6 x 1.9W High Power UV LED
Optics
15 degrees
Output
4500 mW
Project lamp life
20,000 hrs L70 at 25C
Color range
365nm
Cable connection
22 AWG wire cable
Housing
Aluminum die casting
Protection rating
IP-65
Dimension
L 110.5 x W 49.8 x H 134.25 mm
Dry weight
0.71 kg

C08SPT510