Anyload 805HP User manual

805HP
Handheld Digital Weight Indicator
Operations Manual (V1612)
Anyload Transducer Co. Ltd
Website: www.anyload.com
Email: [e-mail]

TABLE OF CONTENTS
1. Introduction and Product Features 3
2. Safety Recommendations 3
3. Display Icon List 4
4. Key List 4
5. Operation Mode 5
6. Start Up 6
6.1 805HP Wired Model 6
6.2 805HP Wireless Model 7
7. Modes 7
7.1 Normal Weighing Mode 7
7.2 Gross/Net Mode 8
7.3 Peak Mode 8
7.4 Cumulate Mode 9
7.5 Calibration Mode 10
8. Configurations and Menu Operations 10
8.1 Menu Operations 10
8.2 Overload 14
8.3 Modify Password 14
9. Communication 15
9.1 RS232 Communication 15
9.2 Wireless Communication 16
10. Calibration 16
10.1Weight Calibration 17
10.2 Digit Calibration 18
11. Troubleshooting Guides 19
12. Technical Specifications 20
1 | ANYLOAD 805HP Handheld Digital Weighing Indicator Operations Manual (V1612)

1. Introduction and Product Features
Thank you for choosing Anyload 805HP Handheld Digital Weight Indicator.
The 805HP hand held digital weight indicator is a general purpose durable
indicator that provides high accuracy, reliability, and multiple functions. The
805HP can drive up to eight 350Ω or thirty two 1000Ω load cells. With an IP65
ABS wash down enclosure, the 805HP digital weighing indicator is ideal for use
in Transportation, Entertainment, Aerospace, Military, Food and Agricultural
industry
Key Features include:
Exceptionally long battery life: up to 1,600 hours with 3-AA
batteries
LED backlight and panoramic FSTN LCD view angle
Material: ABS
IP Rating: IP65
LCD 6-digit display with LED backlight
Non-volatile memory for reliable data saving
Units of Measurement: kg, g, t, lb, Klb, N, kN, oz, user-
defined unit
Configurable 2 set-points for precaution and warning
User-selectable display interval
Overloading recording
10 user-selectable analog-to-digital converting frequency
Weight calibration and digital calibration
User-selectable auto power-off and power-saving timing
Functions: Auto-Zero Tracking, Auto-Zero, Manual-Zero,
Hold, Peak-Hold, TARE
This manual provides installation, operation and configuration information of
805HP indicator. It is recommended to go through the manual in details before
installing, operating or configuring the indicator.
2. Safety Recommendations
Important instructions, which involve safety, are highlighted with the
appropriate mark:
2 | ANYLOAD 805HP Handheld Digital Weighing Indicator Operations Manual (V1612)

When it is required to work inside the indicator enclosure for some
procedures described, the work can only be performed by qualified technical
personnel.
3. Display Icon List
Icon
Meaning
Battery Power
Peak hold mode
Save weight to memory
Acquire Tare value
Gross weight
Cumulate Mode
Zero Scale
Wireless communication is normal
Weight surpassed “overload warning value “signal
Signal stability
There is a hidden figure which will be shown on the
following page
4. Key List
Buttons
Modes
Normal
Peak
Cumulate
Menu
【SWITCH】
Short press
Long press
Turn Off
Turn Off
【
CUMULATE
】
Short press
Accumulate
Add weight to
memory
Enter
Long press
Go to
Cumulate
Mode
Return to
normal
weighing
mode
Add/Delete
decimal
point
3 | ANYLOAD 805HP Handheld Digital Weighing Indicator Operations Manual (V1612)

【ZERO】
Short press
Zero scale
Long press
Clear
Cumulative
value
【HOLD】
Short press
Holding/
Cancel
Clear Peak
Value
Show the
lowest five
digits
Long press
Go to Peak
Mode
Return to
Normal
Weighing
Mode
【TARE】
Short press
Tare/Untare
Gross/Net
Cumulative
Value
Long press
【UNITS】
Short press
Switching
units
Show the
highest five
digits
Long press
5. Operation Mode
4 | ANYLOAD 805HP Handheld Digital Weighing Indicator Operations Manual (V1612)

Operation mode
Function
Power-off
When the indicator is turned off, date will be saved in
non-volatile memory.
Operation mode
When the indicator enter wake-up mode, all functions
are enable, and the power run dynamically.
Power-saving
LCD is on, but backlight is off. RS-232 circuit shut down.
6. Start Up
6.1 805HP Wired Model
Connect load cell (communication & printer) to 805HP according
to the following connection diagram:
5 | ANYLOAD 805HP Handheld Digital Weighing Indicator Operations Manual (V1612)

Press【SWITCH】for one second, indicator is turned on. After indicator cycles
through from 0 to 9, the indicator will enter Normal Weighing mode
6.2 805HP Wireless Model
The indicator was set to match the corresponding wireless transceiver before it
leaves the factory. If you need to change the indicator or wireless transceiver
due to radio frequency interference, you can configure the communication
parameters with the following steps in Section 9.2- Wireless Communication of
this manual.
7. Modes
Once the indicator is turned on or restarted the mode will automatically set to
Normal Weighing mode. It can be set to various modes like Peak mode,
Gross/Net Mode or Cumulate Mode
7.1 Normal Weighing Mode
When indicator is set to the Normal Weighing mode, (Peak mark) will
not appear in the display
6 | ANYLOAD 805HP Handheld Digital Weighing Indicator Operations Manual (V1612)

7.1.1 Basic Operations in Normal Weighing Mode
I. Zero Scale
When in the Gross weight mode, (Tare mark) does not appear and (Gross
weight) appears. Remove the load from the scale and wait until (Stable mark)
appears. Press ↑【ZERO】, and (Zero mark) appears. Zero Scale setting
completed
II. Acquire Tare Value
When no Tare is stored ( [Tare mark] does not appear), place the load on the
scale and wait until (Stable mark) appears. Press ↓【TARE】, Tare weight is
stored. Display is in Net weight when (Tare mark) is displayed, (Gross weight
mark) disappears.
III. Remove Stored Tare Value
When indicator has stored tare weight value other than 0 ( [Tare mark]
appears), press ↓【Tare】to remove the stored tare weight value. Display is in
Gross weight mode when (Tare mark) is not displayed.
7.2 Gross/Net Mode
When tare weight is stored (indicator has stored tare weight value other
than 0), press ↓【TARE】to change from net weight to gross weight or
vice versa.
(Gross Weight mark) appears when in gross weight mode.
(Gross Weight mark) disappears when in net weight mode.
7.3 Peak Mode
To activate Peak Weighing Mode, long press →【HOLD】and (Peak mark)
appears
7 | ANYLOAD 805HP Handheld Digital Weighing Indicator Operations Manual (V1612)

I. Peak/Normal Weighing Mode
When (Peak mark) appears, peak mode is activated. Display always shows the
maximum value of load which has been applied to the load cell. When the load
is removed, display still shows the peak load. When (Peak mark) disappears,
peak mode is deactivated. Value shown on display changes according to the
load applied to the load cell. Long press →【HOLD can change indicator from
Peak mode to Normal Weighing mode, or vice versa.
II. Remove Peak Mode Value
When Peak mode is on ( (Peak mark] appears), remove the load and short press
→ 【HOLD】.Peak mode value is removed, and indicator starts another Peak
mode operation
7.4 Cumulate Mode
I. Save Value of Weight to Memory
Short press ↙【CUMULATE】, display will flash ‘total’. (Memory mark) will
appear. Weight is now saved to memory
II. Show Accumulated Weight
Long press ↙【CUMULATE】, indicator changes to Cumulate mode from
weighing mode or peak mode, or vice versa.
When indicator is in Cumulate mode, display shows the accumulated total gross
weight value
III. Gross/Net Mode
Press ↓【TARE】, indicator changes from Gross mode to Net mode, or vice
versa.
Display shows total gross weight value while (Gross Weight mark) appears.
Display shows total net weight value while (Gross Weight mark) disappears
8 | ANYLOAD 805HP Handheld Digital Weighing Indicator Operations Manual (V1612)

IV. Clear Cumulative Value
Long press ↑【ZERO】，total gross weight value and total net weight value
will be cleared
7.5 Calibration Mode
In this mode, you have to enter the menu and parameter settings module.
(Refer to Section 10 of this manual for Calibration of the scale)
8. Configurations and Menu Operations
8.1 Menu Operations
I. Menu Settings
II. Menu Operations
Entering in the menu :
Press ↑,↓ at the same time for 1 second, the indicator will show
asking for the password. The password is
Press directional ←,→,↑,↓ to input the passwords, and press ↙ to enter the
configuration menu.
If invalid password is entered, display will re-enter weighing mode.
9 | ANYLOAD 805HP Handheld Digital Weighing Indicator Operations Manual (V1612)