Makita LD080P User manual

Makita LD080P 1
en
Table of Contents
Instrument Set-up- - - - - - - - - - - - - - - - - - - - - - -2
Introduction- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -2
Overview - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -2
Display - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -3
Insert batteries - - - - - - - - - - - - - - - - - - - - - - - - - - - -3
Operations - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -4
Switching ON/OFF - - - - - - - - - - - - - - - - - - - - - - - - -4
Clear - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -4
Message Codes - - - - - - - - - - - - - - - - - - - - - - - - - - -4
Adjusting measuring reference / tripod - - - - - - - - - - -4
Multifunctional endpiece- - - - - - - - - - - - - - - - - - - - - -5
Distance unit setting - - - - - - - - - - - - - - - - - - - - - - - -5
Timer (automatic release) - - - - - - - - - - - - - - - - - - - -5
Beep ON/OFF- - - - - - - - - - - - - - - - - - - - - - - - - - - - -6
Illumination ON/OFF - - - - - - - - - - - - - - - - - - - - - - - -6
Keypad lock ON - - - - - - - - - - - - - - - - - - - - - - - - - - -6
Keypad lock OFF - - - - - - - - - - - - - - - - - - - - - - - - - -6
Measuring Functions - - - - - - - - - - - - - - - - - - -7
Measuring single distance - - - - - - - - - - - - - - - - - - - -7
Permament / Minimum-Maximum measuring - - - - - - -7
Add / Subtract - - - - - - - - - - - - - - - - - - - - - - - - - - - - -7
Area- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -8
Volume- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -9
Pythagoras (2-point) - - - - - - - - - - - - - - - - - - - - - - - 10
Pythagoras (3-point) - - - - - - - - - - - - - - - - - - - - - - - 10
Pythagoras (partial height) - - - - - - - - - - - - - - - - - - - 11
Stake out - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 12
Memory (20 last displays) - - - - - - - - - - - - - - - - - - - 12
Delete Memory - - - - - - - - - - - - - - - - - - - - - - - - - - - 12
Technical Data - - - - - - - - - - - - - - - - - - - - - - - - - 13
Message Codes - - - - - - - - - - - - - - - - - - - - - - - -14
Care - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -14
Safety Instructions - - - - - - - - - - - - - - - - - - - - -14
Areas of responsibility - - - - - - - - - - - - - - - - - - - - - -14
Permitted use - - - - - - - - - - - - - - - - - - - - - - - - - - - -15
Prohibited use - - - - - - - - - - - - - - - - - - - - - - - - - - - -15
Hazards in use - - - - - - - - - - - - - - - - - - - - - - - - - - -15
Limits of use - - - - - - - - - - - - - - - - - - - - - - - - - - - - -15
Disposal - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -15
Electromagnetic Compatibility (EMC)- - - - - - - - - - - -15
FCC statement (applicable in U.S.) - - - - - - - - - - - - -16
Laser classification- - - - - - - - - - - - - - - - - - - - - - - - -16
Labelling - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -16

Makita LD080P
2
en
Instrument Set-up
Introduction
The safety instructions and the user manual should be
read through carefully before the product is used for the
first time.
The person responsible for the product must ensure that
all users understand these directions and adhere to them.
The symbols used have the following meanings:
WARNING
Indicates a potentially hazardous situation or an unintended use
which, if not avoided, will result in death or serious injury.
CAUTION
Indicates a potentially hazardous situation or an unintended use
which, if not avoided, may result in minor injury and/or appreci-
able material, financial and environmental damage.
Important paragraphs which must be adhered to in practice
as they enable the product to be used in a technically
correct and efficient manner.
i
Overview
®
®
Display
On/Measure
Area /
Volume /
Pythagoras/
Stake out
Clear / Off
Subtract
Add
Timer
Measuring
reference /
Units
Memory

Makita LD080P
Instrument Set-up
3
en
Display
Area /
Volume
Units
Stake out
Circumfer-
ence
Measuring
reference
2nd result
Battery
Angle
Addition /
Subtraction
Timer
Memory
Pythagoras
Min/Max
Measuring
Main line
Wall area
Insert batteries
i
To ensure a reli-
able use, do not
use zinc-carbon
batteries.
Change batter-
ies when battery
symbol is flash-
ing.

Makita LD080P
4
en
Operations
Switching ON/OFF Clear Message Codes
2 sec
Device is
turned OFF.
i
Press ON but-
ton 2 sec to start
continuous laser
mode. If no key
is pressed for
180 sec, the de-
vice switches off
automatically.
1x
Undo last action.
2x
Leave actual
function, go to de-
fault operation
mode.
If the info icon appears with a
number, observe the instruc-
tions in section "Message
Codes".
Example:
Adjusting measuring reference / tripod
Distance is measured from the
front of the device.
1
Distance is measured
from the tripod thread
permanently.
2
Distance is measured from the rear
of the device (standard setting).
3

Makita LD080P
Operations
5
en
Multifunctional endpiece
i
The orientation
of the endpiece
is automatically
detected and
the zero point is
accordingly ad-
justed.
Distance unit setting
0.000 m
0.0000 m
0.00 m
0.00 ft
0‘00‘‘ 1/32
0.00 in
0 in 1/32
2 sec
Switch between the
following units:
Timer (automatic release)
s
1
Adjust delay of au-
tomatic release
(max. 60 sec,
standard setting
5sec)
2
i
Once the key is released with the
laser activated, the remaining sec-
onds until the measurement are
displayed in a countdown. The de-
layed release is recommended for
precise aiming e.g. at long distanc-
es. It avoids shaking of the device
when pressing the measurement
key.

Makita LD080P
Operations
6
en
Beep ON/OFF Illumination ON/OFF
2 sec
simultane-
ously
2 sec
simultane-
ously
Keypad lock ON Keypad lock OFF
2 sec
simultane-
ously
PRESS
MINUS
1
within
2 sec
2

Makita LD080P 7
en
Measuring Functions
Measuring single distance
1
Aim active laser at target.
2
8.532 m
3
i
Target surfaces: Measuring
errors can occur when meas-
uring to colourless liquids,
glass, styrofoam or semi-per-
meable surfaces or when
aiming at high gloss surfac-
es. Against dark surfaces the
measuring time increases.
Permament / Minimum-Maximum measuring
1
2 sec
8.532 m
Used to measure room diagonals (maximum val-
ues) or horizontal distance (minimum values)
The minimum and maximum dis-
tance measured is displayed
(min, max.). The last value meas-
ured is displayed in the main line.
min. max.
2
Stops permanent / mini-
mum-maximum measuring.
3
Add / Subtract
7.332 m
1
The next meas-
urement is added
to the previous
one.
2
The next meas-
urement is sub-
tracted from the
previous one.
5.515 m
12.847 m
3
i
The result is shown in the
main line and the measured
value above. This process
can be repeated as required.
The same process can be
used for adding or subtracting
areas or volumes.

Makita LD080P
Measuring Functions
8
en
Area
1
1x
2
Aim laser at first
target point.
3
4
Aim laser at sec-
ond target point.
24.352 m
2
5
i
The result is shown in the
main line and the measured
value above.
19.823 m
24.352 m
2
2 sec Circumference
Area
6

Makita LD080P
Measuring Functions
9
en
Volume
1
2x
2
Aim laser at first
target point.
3
4
Aim laser at sec-
ond target point.
5
6
Aim laser at third
target point.
78.694 m
3
7
i
The result is
shown in the
main line
and the
measured
value above.
80.208 m
78.694 m
3
208.703 m
2
2 sec
Circumference
Volume
8
Wall areas

Makita LD080P
Measuring Functions
10
en
Pythagoras (2-point)
1
3x
2
Aim laser at up-
per point.
3
4
Aim laser rectan-
gular at lower
point.
8.294 m
5
i
Notice additional
Pythagoras
measurement in-
formation at the
bottom of the
next page.
Pythagoras (3-point)
1
4x
2
Aim laser at up-
per point.
3
4
Aim laser at rec-
tangular point.
5
6
Aim laser at lower point.
8.294 m
7
i
Notice additional
Pythagoras
measurement in-
formation at the
bottom of the
next page.

Makita LD080P
Measuring Functions
11
en
Pythagoras (partial height)
1
5x
2
Aim laser at up-
per point.
3
4
Aim laser at 2nd
point.
5
6
Aim laser at rec-
tangular point.
2.602 m
7
i
•The result is shown in the main line and the measured distance above.
•A reduced level of accuracy, lower than the level of accuracy of the instrument
itself, must generally be expected when the Pythagoras measuring method is
used. In order to obtain the best results we recommend to use a tripod or to flip
out the corner end piece.
•Pressing the measuring key for 2 sec in the function activates automatically
Minimum or Maximum measurement.
Pythagoras
measurements:

Makita LD080P
Measuring Functions
12
en
Stake out
1
2
3
1.000 m
1
6x
0.625 m
2
Adjust
value.
3
Approve value and
start measurement.
4
Move device
slowly along the
stake-out line.
The distance to
the next stake
out point is dis-
played.
0.625 m
0.240 m
0.240 m is missing
up to next 0.625 m
distance.
i
When approaching a stake
out point to less than 0.1 m
the instrument starts to
beep.
The function can be stopped
by pressing the CLEAR/OFF
button.
Memory (20 last displays) Delete Memory
8.294 m
20
20 last displays
are displayed.
1
8.294 m
20
Navigates trough
20 last displays.
2
The value from
the main line can
be used for fur-
ther calculations.
2 sec
1
2 sec
simultaneously
Memory is completely de-
leted.

Makita LD080P 13
en
Technical Data
* favourable conditions are: white and diffuse
reflecting target (white painted wall), low background
illumination and moderate temperatures.
** unfavourable conditions are: targets with lower or
higher reflectivity or high background illumination or
temperatures at the upper or lower end of the speci-
fied temperature range.
*** Tolerances apply from 0.05 m to 10 m with a confi-
dence level of 95%.
With favourable conditions the tolerance may deterio-
rate by 0.10 mm/m for distances between 10 m to
30 m and by 0.15 mm/m for distances above 30 m.
With unfavourable conditions the tolerance may dete-
riorate by 0.15 mm/m for distances between 10 m to
30 m and by 0.20 mm/m for distances above 30 m.
For accurate indirect results, the use
of a tripod is recommended. For
accurate tilt measurements a trans-
verse tilt should be avoided.
Distance measurement (ISO 16331-1)
Accuracy with favourable
conditions *
± 1.5 mm / 0.06 in ***
Accuracy with unfavourable
conditions **
± 2.5 mm / 0.10 in ***
Range with favourable
conditions *
80 m / 262 ft
Range with unfavourable
conditions **
60 m / 197 ft
Smallest unit displayed 0.1 mm / 1/32 in
Ø laser point
at distances
6 / 30 / 50 mm
(10 / 50 / 80 m)
General
Laser class 2
Laser type 635 nm, < 1 mW
Protection class IP54 (dust- and splash
water protected)
Autom. laser switch off after 90 s
Autom. power switch-off after 180 s
Battery durability (2 x AAA) up to 5000 measure-
ments
Dimension (H x D x W) 117 x 57 x 32 mm
4.6 x 2.4 x 1.3 in
Weight (with batteries) 0.14 kg / 4.938 oz
Temperature range:
- Storage
- Operation
-25 to 70 °C
-13 to 158 °F
-10 to 50 °C
14 to 122 °F
i
Functions
Distance measuring yes
Min/Max measuring yes
Permanent measuring yes
Stake-out yes
Addition/Subtraction yes
Area yes
Volume yes
Pythagoras 2-point, 3-point,
partial height
Memory 20 displays
Beep yes
Illuminated display yes
Multifunctional endpiece yes

Makita LD080P
14
en
Message Codes
If the message Error does not disappear
after switching on the device repeatedly,
contact the dealer.
If the message InFo appears with a
number, press the Clear button and
observe the following instructions:
Care
•Clean the device with a damp, soft cloth.
•Never immerse the device in water.
•Never use aggressive cleaning agents
or solvents.
Safety Instructions
The person responsible for the instrument
must ensure that all users understand
these directions and adhere to them.
Areas of responsibility
Responsibilities of the manufacturer
of the original equipment:
Makita Corporation Anjo,
Aichi 446-8502 Japan /
Makita, Jan-Baptist Vinkstraat 2, 3070,
Belgium
Internet: www.makita.com
The company above is responsible for
supplying the product, including the User
Manual in a completely safe condition.
The company above is not responsible for
third party accessories.
Responsibilities of the person in
charge of the instrument:
•To understand the safety instructions on
the product and the instructions in the
User Manual.
•To be familiar with local safety regula-
tions relating to accident prevention.
•Always prevent access to the product by
unauthorised personnel.
No. Cause Correction
156 Transverse tilt
greater than 10°
Hold the instrument
without any transverse
tilt.
162 Calibration mistake Make sure, the device
is placed on a abso-
lutely horizontal and flat
surface. Repeat the
calibration procedure. If
the mistake still occurs,
contact your dealer.
204 Calculation error Perform measurement
again.
252 Temperature too
high
Let device cool down.
253 Temperature too
low
Warm device up.
255 Received signal too
weak, measuring
time too long
Change target surface
(e.g. white paper).
256 Received signal too
high
Change target surface
(e.g. white paper).
257 Too much back-
ground light
Shadow target area.
258 Measurement
outside of meas-
uring range
Correct range.
260 Laser beam inter-
rupted
Repeat measurement.

Makita LD080P
Safety Instructions
15
en
Permitted use
•Measuring distances
•Tilt measurement
Prohibited use
•Using the product without instruction
•Using outside the stated limits
•Deactivation of safety systems and
removal of explanatory and hazard
labels
•Opening of the equipment by using tools
(screwdrivers, etc.)
•Carrying out modification or conversion
of the product
•Use of accessories from other manufac-
turers without express approval
•Deliberate dazzling of third parties; also
in the dark
•Inadequate safeguards at the surveying
site (e.g. when measuring on roads,
construction sites, etc.)
•Deliberate or irresponsible behaviour on
scaffolding, when using ladders, when
measuring near machines which are
running or near parts of machines or
installations which are unprotected
•Aiming directly in the sun
Hazards in use
WARNING
Watch out for erroneous measurements if
the instrument is defective or if it has been
dropped or has been misused or modified.
Carry out periodic test measurements.
Particularly after the instrument has been
subject to abnormal use, and before,
during and after important measurements.
CAUTION
Never attempt to repair the product your-
self. In case of damage, contact a local
dealer.
WARNING
Changes or modifications not expressly
approved could void the user’s authority to
operate the equipment.
Limits of use
Refer to section "Technical data".
The device is designed for use in
areas permanently habitable by
humans. Do not use the product in explo-
sion hazardous areas or in aggressive
environments.
Disposal
CAUTION
Flat batteries must not be disposed of with
household waste. Care for the environ-
ment and take them to the collection points
provided in accordance with national or
local regulations.
The product must not be disposed with
household waste.
Dispose of the product appropri-
ately in accordance with the
national regulations in force in your
country.
Adhere to the national and country
specific regulations.
Product specific treatment and waste
management can be downloaded from our
homepage.
Electromagnetic Compatibility
(EMC)
WARNING
The device conforms to the most stringent
requirements of the relevant standards
and regulations.
Yet, the possibility of causing interference
in other devices cannot be totally
excluded.
i

Makita LD080P
Safety Instructions
16
en
FCC statement (applicable in U.S.)
This equipment has been tested and found
to comply with the limits for a Class B
digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to
provide reasonable protection against
harmful interference in a residential instal-
lation.This equipment generates, uses and
can radiate radio frequency energy and, if
not installed and used in accordance with
the instructions, may cause harmful inter-
ference to radio communications.
However, there is no guarantee that inter-
ference will not occur in a particular instal-
lation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined by
turning the equipment off and on, the user
is encouraged to try to correct the interfer-
ence by one or more of the following
measures:
•Reorient or relocate the receiving
antenna.
•Increase the separation between the
equipment and receiver.
•Connect the equipment into an outlet on
a circuit different from that to which the
receiver is connected.
•Consult the dealer or an experienced
radio/TV technician for help.
Laser classification
The device produces visible laser beams,
which are emitted from the instrument:
It is a Class 2 laser product in accordance
with:
•IEC60825-1 : 2014 „Radiation safety of
laser products“
Laser Class 2 products:
Do not stare into the laser beam or direct it
towards other people unnecessarily. Eye
protection is normally afforded by aversion
responses including the blink reflex.
WARNING
Looking directly into the beam with optical
aids (e.g. binoculars, telescopes) can be
hazardous.
CAUTION
Looking into the laser beam may be
hazardous to the eyes.
Labelling
Subject to change (drawings, descriptions
and technical data) without prior notice.
Description Value
Maximum peak radiant output power 0.95 mW
Wavelength 635 nm
Pulse duration > 400 ps
Pulse repetition frequency 320 MHz
Beam divergence 0.16 x 0.6 mrad
Makita xxxxxxx xxxxxxx xxxxxxx
LD080P
Made in Hungary Batteries: 2 x AAA
Complies with 21CFR 1040.10 and
1040.11 except for deviations pursuant to
Laser Notice No. 50, dated June 24, 2007
®