APART CM6QFT User manual

MANUAL
CM6QFT
The new contractor’s reference

2
The new contractor’s reference
The APart CM6QFT, the new contractor’s reference: reduces the install labour drastically.
The APart CM6QFT 2-way built-in ceiling loudspeaker can be used as a 16 Ohm or 100 Volt
loudspeaker. In 16 Ohm use, you can connect up to 4 loudspeakers in parallel on each channel
of a standard 4 Ohm amplier. For 100 V use, the CM6QFT is equipped with a high-quality 6 Watt
100 Volt transformer with several power tappings. The loudspeaker has a 6 ½” paper cone woofer
what results in a very low distortion. To complete the sound a 1” tweeter has been integrated.
It makes the CM6QFT very suitable for the distribution of microphone calls and back ground
music. The housing is made of high quality ABS. The grille is made of steel. The standard colour
is white.
100V/1.5W : Black (common) – yellow
100V/3W: Black (common) – red
100W/6W: Black (common) – brown
16 ohm: rst disconnect the red and black wire between transformer and speaker. Connect the
speaker line to the free wire end on the speaker. Black = common, red = signal.
Product Highlights
•Patented Quick Fit system breaks all speed records
• No screws : x and nish with 4 clicks only
•Self adjusting clamp strength
•Allowed board tickness : 12.5 to 29 mm
•Discrete and stylish
•Ultra thin plastic edge
• Smooth at design
•Strong metal grill
Speaker power settings

3
The loudspeaker is easy to install, due to its simple, quick mounting system.
Remove the grill before mounting, use the special grille removal tool and carefully
take out the grille.
Make sure the mounting clamps are turned inwards, if this is not the
case, insert the hex key in all four holes on the front and turn it
180 degrees counterclockwise until you hear a click. Insert the speaker
in the ceiling and activate the automatic clamp system. Use the supplied
hex key, but this time you insert the round side in the four holes on
the front. Push the key to release the 4 clamps. Carefully push
the grille back in place. That’s it.
Mounting instructions
Use this round side to push
the key to release the 4 clamps.
Use this hex side to load the
spring of the clamps.
Mounting Dis-mounting
Position the speaker in the ceiling.
Activate the spring clamps by pushing the four
spring clamp buttons with the round end of
the tool.
Turn the spring clamps 180º counter-
clockwise until you hear a click.
Take out the speaker.

4
ANY SUGGESTION?
They are well appreciated and eventually rewarded!
Send your ideas or suggestions to
[email protected]
CM6QFT is developed by
Audioprof nv
Lanteernhofstraat 90
BE-2100 Deurne
BELGIUM
Company names, product names, and names of formats etc. are the trademarks or registered
trademarks of their respective owners.
© 2009 APart-Audio specications subject to change without notice.
Type 2 - Way HiFi
Woofer 6.5” paper cone
Tweeter 1” Soft Dome
Rated Power RMS 6 W / 100Volt
Music Power RMS 10 W / 100Volt
Rated Power RMS 40 W / 16Ω
Music Power RMS 60 W / 16Ω
Sound Pres. Level (SPL) 1W/1M 91dB
Frequency range 60 Hz - 20 kHz
Trafo Power Tappings 6 - 3 - 1.5W
Dispersion @ 1-4-8 KHz 180°- 80° - 45°
Dimensions outside Ø 237mm
Dimensions Cutout Ø 216mm
Depth 65mm
Ceiling thickness 12.5 – 29mm
Weight 1.1Kg
General technical specications