Aqara Door and Window Sensor User manual

Door and Window Sensor

English
Door and Window Sensor
Quick Start Guide
Aqara Door and Window Sensor detects the open and
close state of doors or windows through the distance
between the sensor unit and the magnet. It consumes low
energy. No tools required, and simply peel and stick.
* A hub is required.
* Aqara Hub is required to enable Aqara Door and Window Sensor to
work with HomeKit technology. See www.aqara.com for more details.
* This product is for indoor use only.
Indicator Light
Sensor Unit Magnet Reset Button
Long Press for 3s: Reset/Connect
to Network
Single Press: Eective Range Test
Product Introduction

English
1. Before activating the accessory, please make sure you
have the Aqara Home app downloaded and Aqara hub
installed.
Quick Setup
Eective Range Test: Single press the reset button on the
accessory at your desired position. If the Hub makes voice
prompts, it indicates that the accessory can communicate
eectively with the Hub.
2. Please open the app, tap“Home”and then tap“+” in the
top right corner to enter“Add Device (Accessory)” page.
Select “Door and Window Sensor”, and add it according
to instructions.
* If the connection fails, please move the accessory closer to the
Hub and try again.
* Avoid metal surface to maximize signal strength.
Installation

English
②During installation, try to align the marker line of the
sensor unit and the magnet.
Remove the protective lm
Try to align the marker line
①Remove the protective lm.
③Stick to doors or windows (It is recommended to install the
sensor unit on the unmovable surface, the magnet on the
movable surface, and make sure the installation gap is less
than 22 mm when doors or windows are closed).

English
* Keep the surface clean and dry.
Installation gap less than 22 mm
Model: MCCGQ11LM
Dimensions: 41 × 22 × 11 mm (1.61 × 0.87 × 0.43 in.)
Wireless Protocol: Zigbee
Battery: CR1632
Maximum Detection Distance: 22 mm (0.87 in.)
Operating Temperature: -10° – +50°C (14° – 122°F )
Operating Humidity: 0 – 95% RH, no condensation
Maximum Transmit Power (Zigbee): 9.99 dBm
Working Frequency: 2400 MHz – 2483.5 MHz
Specications

English
This product is NOT a toy. Please keep children away from
this product.
This product is designed for indoor use only. Do NOT use in
humid environments or outdoors.
Beware of moisture, do NOT spill water or other liquids
onto the product.
Do NOT place this product near a heat source. Do NOT
place it in an enclosure unless there is normal ventilation.
Do NOT attempt to repair this product by yourself. All
repairs should be performed by an authorized professional.
This product is only suitable for improving the
entertainment, convenience of your home life and
reminding you about the device status. It should NOT be
used as security equipment for home, building, warehouse
or any other places. If a user violates the product use
instructions, the manufacturer will NOT be liable for any
1.
2.
3.
4.
5.
6.
Warnings
Online Customer Service: www.aqara.com/support
Email: [email protected]
Manufacturer: Lumi United Technology Co., Ltd.
Address: 8th Floor, JinQi Wisdom Valley, No.1 Tangling Road,
Liuxian Ave,Taoyuan Residential District, Nanshan District,
Shenzhen, China.

English
FCC ID: 2AKIT-MCCGQ11LM
Federal Communications Commission (FCC) compliance statement:
1. This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
2. Changes or modications not expressly approved by the
party responsible for compliance could void the user's
authority to operate the equipment.
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment o and on, the user is
risks and property losses.