Aqara Water Leak Sensor User manual

Water Leak Sensor

English
Water Leak Sensor
Quick Start Guide
Aqara Water Leak Sensor detects water leak and ooding and
monitors the status of water leak. When the water leak or
ooding occurs, it sends an instant alert notication via app. It
also works with other smart
*
*
A hub is required.
Aqara Hub is required to enable Aqara Water Leak Sensor to work with
HomeKit technology. See www.aqara.com for more details.
* This product is for indoor use only.
Inductive ProbeIndicator Light
Reset Button
Long Press for 5s: Reset/Connect to Network
Single Press: Eective Range Test
accessories to automate your home.
Product Introduction

English
1. Before activating the accessory, please make sure you have
the Aqara Home app downloaded and Aqara hub installed.
2. Please open the app, tap“Home”and then tap“+” in the top
right corner to enter“Add Device (Accessory)” page. Select
“Water Leak Sensor”, and add it according to
* If the connection fails, please move the accessory closer to the Hub
* Avoid metal surface to maximize signal strength.
Quick Setup
Installation
Option 1: Place it directly on the surface where you need
instructions.
and try again.
to monitor water leak.
Eective Range Test: Single press the reset button on the
accessory at your desired position. If the Hub makes voice
prompts, it indicates that the accessory can communicate
eectively with the Hub.

English
Battery Replacement
Option 2: Use a hex screwdriver to loosen the probes, and
* The antenna is right above the water drop icon.
connect to cables for more smart scenes.
* In order to ensure the dustproof and waterproof performance of the
product, the back cover of the battery must be tightened before use, and
the groove is at the same level as the probe.
1. Insert a coin into the groove of the battery cover and turn
it counterclockwise to open the battery cover;
2. Put a new CR2032 button battery into the battery
compartment, and pay attention to making the side with
the"+" sign face out;
3. Close and tighten the battery cover, and ensure that the
groove of the battery cover is aligned with the metal
probes on both sides in a straight line;

English
Model: SJCGQ11LM
Dimensions: 50 × 50 × 15 mm (1.97 × 1.97 × 0.59 in.)
Wireless Protocol: Zigbee
Battery: CR2032
Operating Temperature: -10° – +55°C (14° – 131°F)
Operating Humidity: 0 – 100% RH
Maximum Transmit Power (Zigbee): 9.99dBm
Working Frequency: 2400 MHz – 2483.5 MHz
Specications
Online Customer Service: www.aqara.com/support
Email: [email protected]
Manufacturer: Lumi United Technology Co., Ltd.
Address: 8th Floor, JinQi Wisdom Valley, No.1 Tangling Road,
Liuxian Ave,Taoyuan Residential District, Nanshan
District, Shenzhen, China.
Tightened in place Not yet tightened in place

English
FCC ID: 2AKIT-SJCGQ11LM
Federal Communications Commission (FCC) compliance
statement:
1. This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
This product is NOT a toy. Please keep children away from
this product.
This product is designed for indoor use only. Do NOT use in
outdoors.
Do NOT place this product near a heat source. Do NOT
place it in an enclosure unless there is normal ventilation.
Do NOT attempt to repair this product by yourself. All
repairs should be performed by an authorized professional.
This product is only suitable for improving the
entertainment, convenience of your home life and
reminding you about the device status. If a user violates
the product use instructions, the manufacturer will NOT be
liable for any risks and property losses.
1.
2.
3.
4.
5.
Warnings