Aqua Creek F-600TLNA User manual

Copyright © 2017 Aqua Creek Products All Rights Reserved Revised 4/14/17
Titan Lift
Manual
PART #: F-600TLNA
US PATENT NUMBER: [D507,769 S]
600 LB. [272 kg] MAXIMUM WEIGHT CAPACITY
MANDATORY
LEAVE THIS MANUAL WITH LIFT OWNER
Read and follow all instructions.
Lift safety can only be ensured if installed and operated
according to these instructions.
• NEVER permit children to play on or around the lift
• Do not allow children to use the lift without adult
supervision
• NEVER apply direct water pressure to the electronics
• NEVER use the lift with a dry pool
Check entire box and all packing materials for parts. Before beginning assembly, read the
instructions and identify parts using the  gures and parts listed in this document.
It is critical that all parts be carefully inspected prior to installation. If any damage occurred in
transit, Aqua Creek Products, LLC must be noti ed within three days of receipt of unit.
Proper installation cannot be overstressed, as an improper installation voids Aqua Creek’s
warranty and may affect the safety of the user.
READ CAREFULLY
9889 Garrymore Ln
Missoula, MT 59808
888-687-3552 | [phone]
www.aquacreek.com
ADA COMPLIANT
1

Copyright © 2017 Aqua Creek Products All Rights Reserved Revised 4/14/17
Titan Lift
Titan Components
1. The Titan Main Assembly
2. Control Arm
3. Lifting Arm
4. Seat Arm
5. Footrest
6. Actuator
7. Handset
8. 24V Battery
Table of Contents
PAGE DESCRIPTION PAGE DESCRIPTION
2 Titan Components 9 Troubleshooting Guide
3 ADA Installation Guidelines 10 Proper Care of Pool & Spa Lifts
4 Anchor Installation: New Construction 11 Titan Parts List
5 ADA Fixing Insert Installation 12 Chair & Footrest Parts List
6-8 Titan Assembly Instructions 13 Warranty
1
2
3
4
5
6
8
7
2

Copyright © 2017 Aqua Creek Products All Rights Reserved Revised 4/14/17
Installation: ADA Guidelines
[40.6cm]
16"
MIN
[91.4cm]
36"
[122cm]
48"
[73.7cm]
29"
[30.5cm]
12"
ADA
REQUIRED
CLEAR DECK
SPACE
POOL WALL WATER
FIGURE 1
ADA Requirements:
The Titan Lift is ADA Compliant.
The installation must meet the following requirements:
• Clear deck space dimensions (see FIGURE 1)
• Installed a minimum of 21 inches from the pool wall
• Deck slope no greater than 1:48
• The seat must submerge at least 18 inches into the water. The lift should be installed at a location with
42 inches - 48 inches of depth (deck to pool fl oor)
• Anchor setbacks are based on straight pool/spa walls. Curved pool/spa walls will effect the anchor setback.
3

Copyright © 2017 Aqua Creek Products All Rights Reserved Revised 4/14/17
Anchor Installation: New Construction or Retro-Fit
You may need to saw cut and remove a portion of an existing pool deck in order to achieve the 11 inch depth
footing requirement. Aqua Creek does NOT recommend a core drill installation for this lift.
To properly install this anchor, you will need to have a concrete footing comprised of 2500 psi concrete that is
11 inches deep and 4 feet - 4 inches square and reinforced with rebar. Refer to Figures A and B below.
If cutting into an existing pool deck, the rebar must be drilled and secured to the surrounding pool deck on
three sides (do not secure into bond beam). The centerline of the anchor should be no less than 9 inches from
the edge of the footing.
NOTE: The anchor setback will vary depending on deck application. 16 inch setback is the minimum for ADA
compliance however, given a typical 1 foot bond beam and the fact that the anchor should be no closer than 9
inches to the edge of your footing, 21 inches may be the closest you can achieve.
1. Determine the best location for the anchor and set the anchor in place. You may use a small mass of wet
concrete to set the anchor in place. Use a level and string lines to make sure the anchor is perpendicular
and will be fl ush with the top of the  nished deck surface.
2. Bond the anchor according to local code requirements using the bonding lug on the bottom of the anchor.
Reference the National Electric Code (NEC) Article 680.26 for speci cs on bonding.
3. Pour the concrete so that the top of the anchor will be fl ush with the FINISHED pool deck surface.
4. Once the concrete has cured, the lift can be put into place.
4'-4"
4'-4"
1'-0"
MIN
9" MIN
28" MAX
2'-2"
4'-4"
3"
CLR
11"
8 1/2"
FACE OF
POOL
4'-4" SQ. X 11" DEEP W/ 6-#5 TRANSVERSE
& 4-#5 LONGITUDINAL TOP & BOTT. (2500PSI)
TITAN ANCHOR
ASSEMBLY
EPOXY TOP MATT
TO EXISTING SLAB
(4" MIN EMBED)
(N) OR (E)
CONC SLAB
TITAN ANCHOR
ASSEMBLY
FIXING
ANCHOR
FIXING ANCHOR
#4 TIE @ TOP MAT
24"
12"
24"
2'-0"
2'-0"
1'-0"
FIGURE A
FIGURE B
4

Copyright © 2017 Aqua Creek Products All Rights Reserved Revised 4/14/17
ADA Fixing Insert Installation (Commercial Applications)
STEP 1: INSTALLING THE LIFT ON THE POOL/SPA DECK
1. Due to the indexed anchor and keyed base of the lift, we recommend installation of the xing insert after
the concrete has cured and you are ready to install the lift into the anchor.
2. Place the main assembly in the anchor and turn until the locking pin on the shaft of the lift lines up and
drops into the locking pin slot in the anchor. DO NOT LIFT THE MAIN ASSEMBLY BY USING THE ELECTRIC
RAM AS A HANDLE. If the transport cart was ordered with the lift, it can be used effectively here. If not,
use two people.
3. Mark the location for the xing anchor hole and remove the lift. (see pg 4, FIGURE A)
4. Drill the hole with a 1 1/4 inch core drill or roto-hammer to a depth of about 4 1/2 inches.
5. Clean the hole out and make sure it is dry. Thread the 1/2 inch bolt into the top of the PVC xing anchor
and test t to verify it can be mounted perpendicular. See Step 1 below.
6. Using a two part construction epoxy, ll the hole approximately half full and carefully insert the PVC xing
anchor into the hole, twisting as you push down to evenly spread the epoxy.
7. Allow the epoxy to cure before securing the lift.
8. Re-install the lift into the anchor and using the 1/2 inch bolt and washer, carefully thread into the installed
anchor until snug. TO PREVENT BREAKING THE FIXING BRACKET, DO NOT OVERTIGHTEN!
TITAN 600
MAIN ASSEMBLY
LOCKING-PIN
LOCKING-PIN SLOT
DECK
POST
FIXING ANCHOR
1/2" X 2"
HEX BOLT
1/2" FLAT
WASHER
STEP 1
5