Aqua Creek Revolution Deep F-702RLNA-DD-04 User manual

Copyright © 2020 Aqua Creek Products All Rights Reserved Revised 6/25/20
Revolution Deep
Draft Lift Manual
Check entire box and all packing materials for parts. Before beginning assembly, read the
instructionsandidentifypartsusingthefiguresandpartslistedinthisdocument.
It is critical that all parts be carefully inspected prior to installation. If any damage occurred in
transit,AquaCreekProducts,LLCmustbenotifiedwithinthreedaysofreceiptofunit.
Proper installation cannot be overstressed, as an improper installation voids Aqua Creek’s
warrantyandmayaffectthesafetyoftheuser.
READ CAREFULLY
9889 Garrymore Ln
Missoula, MT 59808
888-687-3552 | [phone]
www.aquacreek.com PART #: F-702RLNA-DD-04
US PATENT NUMBER: [D507,769 S]
400 LB. [181 kg] MAXIMUM WEIGHT CAPACITY
FOR INDOOR OR OUTDOOR USE
MANDATORY
LEAVE THIS MANUAL WITH LIFT OWNER
ADA COMPLIANT
1

Copyright © 2020 Aqua Creek Products All Rights Reserved Revised 6/25/20
IMPORTANT SAFETY INSTRUCTIONS
  Wheninstallingandusingthiselectricalappliance,basicprecautionsshouldalwaysbe 
  followed,includingthefollowing:
READ ALL INSTRUCTIONS BEFORE USING
WARNING - To reduce the risk of injury, do not permit children to use this product unless they are closely
supervised at all times.
Thisapplianceisnotintendedforusebypersons(includingchildren)withreducedphysical,sensoryor
mentalcapabilities,orlackofexperienceandknowledge,unlesstheyhavebeengivensupervisionor
instruction concerning use of the appliance by a person responsible for their safety.
Awireconnectorisprovidedontheunittoconnectaminimum8AWG(8.4mm2) solid copper conductor
betweenthisunitandthemeansforlocalequipotentialbonding.
Checktheunitperiodicallyforsignsofdeterioration:Keepallnuts,boltsandscrewstighttobesurethe
liftisinsafeworkingcondition.
SAVE THESE INSTRUCTIONS
AxsuppliedADAPOOL/SPALIFTsigninalocationvisiblefromtheliftatalltimes.
Rechargeable batteries are to be removed from the appliance before being charged. Batteries are to be
insertedwiththecorrectpolarity.Iftheapplianceistobestoredunusedforalongperiodoftime,the
batteries should be removed. The supply terminals are not to be short-circuited.
REDUCE THE RISK OF DROWNING!
Supervise children at all times.
No jumping or diving from the lift.
Seatmaybehot,usecautionwhenentering.
Keepcoveredwhennotinuse.Inspectandcleanbeforeuse.
INDOOR BATTERY CHARGER:
AMPERAGE = 0.65 FREQUENCY = 60
24 VOLT BATTERY
AMPERAGE = 8 IP RATING = IPX5
Revolution Deep Draft Lift
2

Copyright © 2020 Aqua Creek Products All Rights Reserved Revised 6/25/20
1
2
3
4
6
8
5
7
Revolution Deep Draft Lift
Revolution Deep Draft Components
Table of Contents
PAGE DESCRIPTION PAGE DESCRIPTION
3 Revolution Deep Draft Components 11 Pinch Point Locations
4 ADA Installation Guidelines 12 Proper Care of Pool & Spa Lifts
5AnchorInstallation:NewConstruction 13 Revolution Deep Draft Parts List
6 ADA Fixing Insert Installation 14 Warranty
7-9 Revolution Deep Draft Assembly
Instructions
10 Basic Troubleshooting
1. The Revolution Deep Draft
Main Assembly
2. Deep Draft Control Arm
3. Deep Draft Lifting Arm
4. Deep Draft Seat Arm
5. Footrest
6. Actuator
7. Handset
8. 24V Battery
3

Copyright © 2020 Aqua Creek Products All Rights Reserved Revised 6/25/20
Installation: ADA Guidelines
ADA Requirements:
The Revolution Lift is ADA Compliant.
Theinstallationmustmeetthefollowingrequirements:
• Clear deck space dimensions (see FIGURE 1)
• Installedaminimumof16inchesfromthepoolwall
• Deck slope no greater than 1:48
• Theseatmustsubmergeatleast18inchesintothewater.Theliftshouldbeinstalledatalocationwith
42inches-48inchesofdepth(decktopoolfloor)
• Anchorsetbacksarebasedonstraightpool/spawalls.Curvedpool/spawallswilleffecttheanchorsetback.
FIGURE 1
[91.4cm]
36"
[122cm]
48"
[30.5cm]
12"
[187.9cm]
74"
[40.6cm]
16"
MIN
[73.7cm]
29"
MIN
POOL WALL
ADA
REQUIRED
CLEAR DECK
SPACE
WATER
4

Copyright © 2020 Aqua Creek Products All Rights Reserved Revised 6/25/20
Anchor Installation: New Construction or Retro-Fit
Youmayneedtosawcutandremoveaportionofanexistingpooldeckinordertoachievethe10inchdepth
footing requirement. Aqua Creek does NOT recommend a core drill installation for this lift.
Toproperlyinstallthisanchor,youwillneedtohaveaconcretefootingcomprisedof2500psiconcretethatis
10inchesdeepand4feet-3inchessquareandreinforcedwithrebar.RefertoFiguresAandBbelow.
If cutting into an existing pool deck, the rebar must be drilled and secured to the surrounding pool deck on
three sides (do not secure into bond beam). The centerline of the anchor should be no less than 9 inches from
the edge of the footing.
NOTE:Theanchorsetbackwillvarydependingonapplicationandanyoptionsyouchooseforthelift.16
inchsetbackistheminimumforADAcompliancehowever,givenatypical1footbondbeamandthefactthat
the anchor should be no closer than 9 inches to the edge of your footing, 21 inches may be the closest you
canachieve.Thechartbelowoutlinestheminimumandmaximumanchorsetbacklocationsfortheavailable
optionsbasedonthispremise.Also,someattachmentswillde-ratetheliftingcapacityofthelift.Refertothe
attachment manual or spec sheet to check for changes in lifting capacites.
1. Determine the location for the anchor based on the options you are ordering or think you may order in the
futureandsettheanchorinplace.Youmayuseasmallmassofwetconcretetosettheanchorinplace.
Usealevelandstringlinestomakesuretheanchorisperpendicularandwillbeflushwiththetopofthe
finisheddecksurface.
2. Bond the anchor according to local code requirements using the bonding lug on the bottom of the anchor.
ReferencetheNationalElectricCode(NEC)Article680.26forspecificsonbonding.
3. PourtheconcretesothatthetopoftheanchorwillbeflushwiththeFINISHEDpooldecksurface.
4. Once the concrete has cured, the lift can be put into place.
ITEM NO. OPTION MIN MAX
F-730RSA-S2 GURNEY 21” 32”
F-706RLSS SLING SEAT 21” 24”
F-734RSA SPINE BOARD 21” 34”
F-705-S2 WHEELCHAIR ADAPTER 21” 34”
4'-3"
2'-1
1
2
"
9"
MIN
1'-0"
MIN.
1'-9" MIN.
3'-0" MAX.
4'-3"
4'-3"
3"
CLR
81
2
"
10"
2"
CLR
EPOXY TOP MATT
TO EXISTING SLAB
(4" MIN. EMBED)
REVOLUTION
BRONZE ANCHOR
SLEEVE
4'-3" SQ. x 10" DEEP
CONC. FTG. W/5 - #5
E.W., TOP & BTM. &
#4 U BAR @ TOP
(SEE FIGURE B)
DECK
POOL
WALL
FIXING
ANCHOR
FIXING
ANCHOR
LOCKING-PIN
SLOT
2'-0"
2'-0"
1'-0"
FIGURE A
FIGURE B
5

Copyright © 2020 Aqua Creek Products All Rights Reserved Revised 6/25/20
ADA Fixing Insert Installation (Commercial Applications)
STEP 1:INSTALLINGTHELIFTONTHEPOOL/SPADECK
1. Place the post of the main assembly into the anchor. DO NOT LIFT THE MAIN ASSEMBLY BY USING THE
ELECTRICRAMASAHANDLE.Ifthetransportcartwasorderedwiththelift,itcanbeusedeffectivelyhere.
Ifnot,usetwopeople.
2. Markthelocationforthefixinganchorholeandremovethelift. (see pg 4, FIGURE A)
3. Drilltheholewitha11/4inchcoredrillorroto-hammertoadepthofabout41/2inches.
4. Cleantheholeoutandmakesureitisdry.Threadthe1/2inchboltintothetopofthePVCfixinganchor
andtestfittoverifyitcanbemountedperpendicular.SeeStep1below.
5. Usingatwopartconstructionepoxy,filltheholeapproximatelyhalffullandcarefullyinsertthePVCfixing
anchorintothehole,twistingasyoupushdowntoevenlyspreadtheepoxy.
6. Allowtheepoxytocurebeforesecuringthelift.
7. Re-installtheliftintotheanchorandusingthe1/2inchboltandwasher,carefullythreadintotheinstalled
anchor until snug. TO PREVENT BREAKING THE FIXING BRACKET, DO NOT OVERTIGHTEN!
DECK
MAIN ASSEMBLY
POST
ANCHOR
1/2" X 2"
HEX BOLT
1/2" FLAT
WASHER
STEP 1
6

Copyright © 2020 Aqua Creek Products All Rights Reserved Revised 6/25/20
Revolution Deep Draft Assembly Instructions
STEP 2: INSTALL LIFTING ARM
LocatetheLIFTINGARMandthefollowinghardware:
• (1)1/2”x2-3/4”SHOULDERBOLT
• (1)3/8”x2”SHOULDERBOLT
• (1)5/16”FLATWASHER
• (1)5/16”NYLOCKNUT
• (1)3/8”FLATWASHER
• (1)3/8”NYLOCKNUT
Remove the shipping strap and all packing from
the LINEAR ACTUATOR. Connect the LIFTING ARM
betweentheMASTandtheLINEARACTUATORas
showninthefigurebelow.Makesuretheendmarked
“B”attachestothemast.TightenNYLOCKNUTS(2)
untilsnugasshowninPHOTO2.
DO NOT OVERTIGHTEN!
STEP 3: INSTALL CONTROL ARM
LocatetheCONTROLARMandthefollowing
hardware:
• (1)1/2”x2-3/4”SHOULDERBOLT
• (1)3/8”FLATWASHER
• (1)3/8”NYLOCKNUT
InstalltheCONTROLARM(endmarked“A”)onto
theMASTasshowninthefigurebelow.Tightenthe
NYLOCKNUTuntilsnugasshowninPHOTO3.DO
NOT OVERTIGHTEN!
STEP 2 STEP 3
1/2" X 2 3/4"
SHOULDER BOLT
3/8" FLAT
WASHER
3/8" NYLOCK
NUT
3/8" X 2"
SHOULDER
BOLT
5/16" FLAT WASHER
5/16" NYLOCK NUT
LIFTING
ARM
ACTUATOR
3/8" NYLOCK NUT
3/8" FLAT WASHER
1/2" X 2 3/4"
SHOULDER BOLT
CONTROL
ARM
7

Copyright © 2020 Aqua Creek Products All Rights Reserved Revised 6/25/20
1/2" X 3"
SHOULDER
BOLT (2)
CONTROL ARM
LIFTING ARM
3/8" NYLOCK
NUT (2)
3/8" FLAT
WASHER (2)
DEEP DRAFT
SEAT ARM
Revolution Deep Draft Assembly Instructions
STEP 4: INSTALL SEAT ARM
LocatetheSEATARMandthefollowinghardware:
• (2)1/2”x3”SHOULDERBOLT
• (2)3/8”FLATWASHER
• (2)3/8”NYLOCKNUT
Install the SEAT ARM at the ends of the CONTROL
ARMandLIFTINGARMasshowninthefiguretothe
left.TightentheNYLOCKNUTSuntilsnugasshownin
PHOTO 4. DO NOT OVERTIGHTEN!
(NOTE: MAKE SURE THE SEAT IS FACING AWAY FROM
THE MAIN ASSEMBLY)
NOTE: FOR APPLICATIONS THAT UTILIZE MULTIPLE
SEAT ARMS (SUCH AS FOR A SLING SEAT OR THE SPA
SEAT-ARM) USE THIS STEP TO REMOVE AND REPLACE
THE SEAT ARM.
STEP 5: ADJUST THE SEAT POSITION
TheSEATASSEMBLYwillarriveattachedtotheSEATARM
adjusted to its highest position. To adjust the SEAT ASSEMBLY
toalowerpositionremovethehardwareasshownbelow.
Slide the SEAT ASSEMBLY to its desired position (in 4 inch
increments)andreinstallthehardware.Themaximum
adjustmentis16inch(down).
DO NOT ATTACH THE SEAT ASSEMBLY ANY LOWER THAN THIS
– ALWAYS USE THE TWO (2) SUPPLIED BOLTS TO ATTACH THE
SEAT ASSEMBLY TO THE CHAIR ARM!
NOTE:Formostapplications,suchaspoolswithaflatdeck,
theseatwillbeinstalledinitslowestposition.Forapplications
whereawallorcurbmustbeclearedtheseatshouldbe
installed in a higher position. In its highest position the seat
willcleara24inch[609mm]highwall(withthepull-out
legrest).
STEP 4
SEAT ASSEMBLY
ADJUSTED TO
LOWEST POSITION
(SEAT WILL ARRIVE
AT HIGHEST
POSITION)
HOLES AT 4"
INTERVALS
ALLOW FOR
ADJUSTMENT
OVER 16"
RANGE
SEAT-ARM
MAIN
ASSEMBLY
STEP 5
5/16" NYLOCK
NUT (2)
5/16" FLAT
WASHER (3)
5/16" X 4 1/2"
HEX BOLT
3/8" X 2"
SHOULDER BOLT
8

Copyright © 2020 Aqua Creek Products All Rights Reserved Revised 6/25/20
1/4" FLAT WASHER
1/4" LOCK WASHER
1/4" X 3/4" THUMB SCREW
FOOTREST ASSEMBLY
24V
BATTERY
CONTROL
BOX
HANDSET
CONTROL
Revolution Deep Draft Assembly Instructions
STEP 6: INSTALL THE FOOTREST
Locate the FOOTREST ASSEMBLY and install it on the
seatasshownbelow.Slidethefootresttubeintothe
square tube that supports the seat until the plastic
sleeveofthefootrestsitsflushwiththefaceofthe
square tube. The threaded hole of the plastic sleeve
shouldalignperfectlywiththeholeinthebottomof
thesquaretube.Installthe1/4”thumbscrew,lock
washerandflatwasherthroughthebottomofthe
square tube and up into the plastic sleeve.
STEP 7: INSTALL 24V BATTERY & HANDSET
Locate the 24V battery, the battery charging unit
and the handset control. Charge the battery for 24
hours then install it on the bracket above the control
boxasshownonPHOTO7.Plugthehandsetcontrol
intothecontrolboxasshowninthefigureandin
thephotosbelow.Pressfirmlytomakesuretheplug
isfullyseatedasshownbelow.
THE LIFT WILL NOT FUNCTION IF THE HANDSET
PLUG IS NOT FULLY SEATED OR IF THE BATTERY IS
NOT PROPERLY ALIGNED.
With the lift completely assembled, run the lift fully
outandbackin3-5times,withoutweight,forthe
lifts“breakin”cycleperiod.
STEP 6
STEP 7
SeatedNot Seated 9

Copyright © 2020 Aqua Creek Products All Rights Reserved Revised 6/25/20
Basic Troubleshooting
Problem: The lift won’t move.
Solution:
1. Make sure the battery is properly seated:
You should hear a click when
the battery is properly seated
on the control box or charger.
Click!
NOT Properly Attached:
Note: the white bracket is
in front of the silver clip,
which will not allow for
an electrical connection
Properly Attached:
Note: the white bracket
is behind the silver clip,
holding it securely to
allow for an electrical
connection
Check the ends of the cords for corrosion or
damage. The cord plugs should be recessed
into the outlet. You should feel them pop into
place when they are correctly inserted.
2. Make sure the cords are properly plugged in:
NOT Properly Inserted:
The cord plug is fl ush with
or sticking out of the outlet
Properly Inserted:
The cord plug is recessed
into the outlet
POP!
The Charger is ON
when the green
light is glowing
The Battery is
CHARGING when the
orange light is glowing
When the Battery is
charged the orange
light will stop glowing
4. Make sure the battery is fully charged:3. Check the contact points:
Make sure the contact points of
the control box and the battery
are not damaged or corroded.
If there is corrosion clean with
Scotch-BriteTM pad. Put some
dielectric grease on the contact
points before reattaching the
battery.
Problem: The lift stopped moving over the water and is stuck.
Solution:
1. Press the emergency button
Use a pen or pencil tip and
stick it into the emergency
button on the front of the
control box to retract the lift.
Note:theliftwillnotretract
if the battery is not fully
charged or if the control box
isnotworking.Theemergency
button only overrides the
remote handset.
10