Aquacal HP9 User manual

AWake up heat pump
The display's backlight will be off when the heat
pump is in sleep mode. To wake up the heat pump,
slowly slide a finger across the buttons.
lThe display will illuminate.
lThe message "KEYPAD UNLOCKED" will
briefly appear.
lThen the water temperature and mode will
display.
BChoose what you want the heat pump to do
CSet a desired temperature (setpoint) for the water
Where are the controls?
The display panel is located in a door compartment on the front of the heat pump. This
compartment is designed to protect the display against harsh weather. It can also be padlocked for
extra security.
lPress the bottom of
the panel to open the
display panel door.
lTo close, push the
display panel up.
Then press the
bottom of the panel
in until a clicking
noise is heard.
What's on the display
Buttons Description
Slowly slide a finger across the buttons from left to right to disable the sleep mode.
Sleep mode will automatically reactivate after three minutes have passed.
Select either the pool or the spa thermostat.
Enter the user menu for heat pump options.
Used to increase temperature set point and navigate through menu options.
Used to decrease temperature set point and navigate through menu options.
Used to select the heat pump's operating mode. Also used to edit or confirm options
in a menu.
Indicators Description
Heating Red LED indicates the unit is heating the water.
Cooling Blue LED indicates the unit is cooling the water.
When calling for heating or cooling, up to a three-minute delay may occur before the compressor
starts. The compressor must be operating before the indicator will illuminate.
Quick Start Guide
LTP0117 Rev. 1.03- (project rel 7.02)

Why is my heat pump asking for an entry code?
If a user entry code has been enabled in the user menu, an entry code will be required to access heat
pump options.
Heating the water for the first time?
1. Confirm heat pump mode has been set to heating mode.
2. Set the desired temperature (set-point) for the water.
3. Temporarily set the filter pump for continuous operation.
4. Use a pool cover or blanket to reduce heating time.
Cooling the water for the first time?
1. Confirm heat pump mode has been set to cooling mode.
2. Set thermostat to desired water temperature.
3. Temporarily set the filter pump for continuous operation.
Water under the heat pump?
Water may be seen around the heat pump. This is normal condensation produced as a byproduct of
this type of system.
lThe amount of condensation depends on the amount of humidity in the air. Quantities of 8 to 10 gallons
(30 to 38 liters) per hour are common. Low humidity may result in no condensation.
lKeep the drain holes at the base of the unit free of grass and weeds. This will allow condensation to
drain from the heat pump. If the heat pump is located under trees, leaves may fall and accumulate in
the bottom of the unit. Accumulated debris should be removed by a qualified technician.
Pool Blankets
A pool blanket can assist the heater to maintain water temperature while significantly reducing
heating costs. Conventional blankets, commonly referred to as "Solar Blankets", are a thin plastic-
like membrane that floats on the water surface. To be effective solar blankets are physically placed
over the water surface when the pool is not in use.
WARNING Failure to heed the following may result in injury or death.
lImproperly used, Pool-Spa solar blankets can become a drowning risk to people and pets. Solar blankets
are not safety covers. They are not designed to support the weight of a person or pet. Never enter a pool
until the solar cover is completely removed. Under no circumstances should anyone swim under the
blanket. Follow all safety recommendations of the blanket manufacturer.
Liquid Blankets
For those who want to save on heating costs, but do not want the bother and potential dangers of a
conventional blanket, a liquid blanket can be a viable alternative. A liquid-blanketed pool on
average loses only 30% of its heat gain overnight. However, strong winds can reduce the
effectiveness of liquid blankets. Check your pool dealer / supplier for more information on pool
blankets and liquid blankets.
Clearances
lProper air circulation is required for the heat pump to operate efficiently. The following diagrams
show the minimum clearances required for the proper operation of the heat pump.
lAvoid storing chemical containers near the heat pump. The chemicals can cause equipment damage.
lAvoid placing objects near or on top of the heat pump. This includes shrubbery and lawn furniture.
These objects will reduce performance and efficiency and hinder maintenance access.
(Overhead Clearance) (Top View)
How can Ifind out more about my heat pump?
Please go online at www.AquaCal.com for installation, maintenance, winterization, equipment or
troubleshooting advice.
Contacting AquaCalAutoPilot, Inc.
For further assistance, please contact the distributor or installer of this product.
If unavailable, please contact AquaCal®for a partner in your area. To better assist you, please have
the heat pump model and serial number available.
Product Information:
Website www.AquaCal.com
Phone [phone]
Hours 8-5 pm, Eastern M-F
Service Information:
Website www.AquaCal.com/request-heat-pump-service/
Phone [phone]
Hours 8-5 pm, Eastern M-F