Aquacal TropiCal T115 Programming manual

1
ATTENTION INSTALLER:
THIS DOCUMENT IS PURCHASER’SPROPERTY AND IS TO REMAIN WITH THE HEAT PUMP OWNER
Models:
T65
T115
T135
Pool and Spa
Heat Pump
Owner’s Manual
and
Installation Guide
PN: LTP0009
01/12/04
1/7/04
(Also Applies to All C115 Models)

2
NOTES
___________________________________________________________________________________
__________________________________________________________________________________
___________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
___________________________________________________________________________________
__________________________________________________________________________________
___________________________________________________________________________________
_________________________________________________________________________________
__________________________________________________________________________________
________________________________________________________________________________________
___________________________________________________________________________________
____________________________________________________________________________________
_________________________________________________________________________________
__________________________________________________________________________________
_________________________________________________________________________________
__________________________________________________________________________________
__________________________________________________________________________________
1-800-786-7751

3
TABLE OF CONTENTS
WELCOME TO THE TEAM ------------------------------------------------------------------ 4
IMPORTANT FEATURES OF YOUR NEW HEAT PUMP -------------------------------- 5
SAFETY INFORMATION --------------------------------------------------------------------- 6
QUICK START & STOP ----------------------------------------------------------------------- 8
PHYSICAL CHARACTERISTICS & PERFORMANCE ----------------------------------- 9
Dimensional Information - TropiCal Models T65 and T115 --------------------------- 9
Dimensional Information - TropiCal Model T135 -------------------------------------- 10
TropiCal: Table of Specifications--------------------------------------------------------- 11
Refrigerant Circuit Performance Charts ------------------------------------------------- 11
Guide: Troubleshooting Refrigerant Circuit Problems --------------------------------- 13
INSTALLATION -------------------------------------------------------------------------------- 14
Placement of Heater------------------------------------------------------------------------- 14
Plumbing Requirements--------------------------------------------------------------------- 16
Electrical Requirements -------------------------------------------------------------------- 18
START-UP & OPERATION ------------------------------------------------------------------- 20
Overview of Controls------------------------------------------------------------------------ 21
Initial Start-up and Basic Operation ------------------------------------------------------- 21
Heating Tips ---------------------------------------------------------------------------------- 22
Calculating Initial Heating Time ----------------------------------------------------------- 23
MAINTENANCE ------------------------------------------------------------------------------- 24
Planned Maintenance ----------------------------------------------------------------------- 25
General Maintenance ----------------------------------------------------------------------- 25
Maintaining Proper Water Flow ----------------------------------------------------------- 26
Maintaining Proper Clearances Around Heater ------------------------------------------ 27
SEASONAL USE & SHUT DOWN ---------------------------------------------------------- 27
During the Swim Season -------------------------------------------------------------------- 27
Freeze protection / Extended Shut Downs ------------------------------------------------ 27
Winterizing (Hard Freeze Conditions) --------------------------------------------------- 27
TROUBLESHOOTING ------------------------------------------------------------------------ 29
Common Troubleshooting Issues ---------------------------------------------------------- 29
Troubleshooting Flow Charts --------------------------------------------------------------- 30
REPLACEMENT PARTS --------------------------------------------------------------------- 34
CONTACTING THE FACTORY -------------------------------------------------------------- 35

4
Welcome
eam
T
“You can rest assured
that your new heat
pump is of the highest
quality and efficiency,
and is designed and
built to provide years of
trouble-free
operation.”
to the
Dear Owner:
Congratulations on your wise decision to make an AquaCal heat pump part of your home. Since
1981, AquaCal has maintained the worldwide lead in the manufacture of swimming pool & spa
heat pumps. Your new heat pump is not only a
great investment, but also the most cost effective method
available for heating pools and spas. For example, as a
means to heat pool or spa water, your heat pump is up to
400% more efficient than gas, and, when compared to
electric resistance heat, your heat pump is nearly 600%
more effective. You can rest assured that your new heat
pump is of the highest quality and efficiency, and is
designed and built to provide years of trouble-free
operation.
Moreover, should you decide you would like
AquaCal to provide regular inspection and maintenance
for your heat pump—which we do recommend—you
will find AquaCal has the largest and best-qualified
service staff in the pool & spa heat pump industry.

5
ThermoLink Heat
Exchanger:
The heart of your heat
pump is the patented
ThermoLink heat ex-
changer. The primary
cause of premature
heat pump demise is
the failure of the heat
exchanger. Ordinary
heat exchangers are
made from a cupron-
ickel alloy. This cu-
pronickel material is
susceptible to attack
from the sanitizers used in pools and spas, and from
other related water chemistry conditions. Once the heat
exchanger fails, the heat pump is ruined. The
ThermoLink heat exchanger tube is made from tita-
nium, and is virtually impervious to water-chemistry
damage.
Electronic
Controller:
State-of-the-art, solid-state
electronic controller, main-
tains water temperature
within 1ºF of set point. Con-
troller also permits user to
predefine different Pool and
Spa water temperature set
points.
Corrosion-Resistant
Cabinet:
Hybrid design utilizes the best
features of finished aluminum and resilient ABS plas-
tic. The base, being ABS material, will never rust or
corrode. The remainder of the cabinet is constructed
from sturdy, marine-grade, powder-coated aluminum.
PLEASE SPEND A FEW MINUTES READING FURTHER TO BECOME
FAMILIAR WITH ALL THE FEATURES, THE SAFE OPERATION, AND THE
CARE OF YOUR NEW HEAT PUMP.
(135-Series)
IMPORTANT FEATURES OF
YOUR NEW HEATPUMP
ThermoLink
Heat Exchanger
Electronic Controller
Corrosion-Resistant
Cabinet
a
a
a

6
Used and maintained properly, your heat pump will provide year-upon-year of safe and economical service.
However, as with any mechanical or electrical device, to get the most from your heat pump–while insuring
personal safety for you and others–certain operational and maintenance factors must be observed.
Likewise, excepting a few minor owner-capable maintenance items (explained later in this manual), repair and
service of your heat pump must be performed only by experienced service personnel. Should you, the owner,
suspect your heat pump is not performing properly, by referring to the section in this manual entitled:
"Troubleshooting", you will be able to determine if a call for service is required. Your installer can be one source
of service, or AquaCal Customer Support personnel stand ready to assist you at: [phone]. For questions
concerning installation, modifications, operation, service and upkeep, please contact your installer or AquaCal
Customer Support. Warranties may be voided if the heater has been used, maintained, or repaired improperly.
In addition to possible voiding of warranties: unapproved installation methods, nonstandard modifications, poor or
incorrect maintenance, service by unqualified personnel, or improper use of this unit, may result in personal injury
and/or property damage. For personal safety and to avoid damage to equipment, it is important that safety
instructions displayed on the heat pump, and within this manual, are read, understood, and followed.
Throughout this manual the following two safety signals are placed where particular care is required. Please note
"WARNING" relates to personal safety, while "CAUTION" signals promote avoiding damage to equipment.
SAFETY INFORMATION
This “Caution” symbol appears in this manual where special care is required to avoid equipment damage.
Failure to heed the following may result in damage to equipment.
CAUTION !
Specific instructions will appear in this box.
Water Temperature Safety
WARNING ! Failure to heed the following may result in permanent injury or
death.
Prolonged immersion in water warmer than normal body temperature may cause a condition known as
HYPERTHERMIA. The symptoms of hyperthermia include: unawareness of impending hazard, failure
to perceive heat, failure to recognize the need to exit the spa and unconsciousness. The use of alcohol,
drugs, or medication can greatly increase the risk of fatal hyperthermia. In addition, persons having an
adverse medical history, or pregnant women should consult a physician before using a hot tub or spa.
Children and the extreme elderly should be supervised by a responsible adult.
This “Warning” symbol appears in this manual where special attention is required for personal safety.
Specific instructions will appear in this box.
Failure to heed the following may result in permanent injury or
death.
WARNING !

7
Refrigerant Circuit Service Only by
Qualified, EPA Certified Technician
Heater NOT Repairable by Owner
WARNING ! Failure to heed the following may result in permanent injury or
death.
Heat pumps contain no owner-repairable components. Repairs must not be attempted by untrained
and/or unqualified individuals. If service is deemed necessary, contact installing dealer or AquaCal
Customer Support at [phone].
Water Chemistry Safety
Chlorine . . . . . . . . . . . . . . .:
Bromine . . . . . . . . . . . . . . .:
pH . . . . . . . . . . . . . . . . . . .:
Total Alkalinity . . . . . . . . . .:
Calcium Hardness . . . . . . . .:
Total Dissolved Solids . . . . .:
1.0 – 3.0 ppm in pools, 1.5 – 3.0 ppm in spas
2.0 – 4.0 ppm in pools, 3.0 – 5.0 ppm in spas
7.4 – 7.6 ppm in pools, 7.2 – 7.8 ppm in spas
80 – 140 ppm in pools, 80 – 120 ppm in spas
200 – 400 ppm in pools and spas
1,000 – 2,000 ppm in pools,
1,500 ppm above start-up TDS in spas
RECOMMENDED WATER CHEMISTRY STANDARDS
While your heat pump’s titanium-based heat exchanger provides nearly impervious protection against
poor water chemistry, improper water chemistry may cause expensive damage to pump, filter, pool
shell, etc. To avoid equipment damage, maintain Pool-Spa water per standards below.
Failure to heed the following can result in damage to equipment.
CAUTION !
Improper water chemistry can present a serious health hazard. To avoid possible hazards, maintain
Pool-Spa water per standards below.
Failure to heed the following may result in permanent injury or
death.
WARNING !
WARNING ! Failure to heed the following may result in permanent injury or
death.
Heater contains refrigerant under high pressure. Repairs to the refrigerant circuit must not be
attempted by untrained and/or unqualified individuals. Service must be performed only by qualified
HVAC technicians. Recover refrigerant to relieve pressure before opening system.

8
This brief information is provided as an aide to installers, service personnel, and owners. The intent of this
section is to provide rapid access to (only) very basic operational information. Individuals who will be
routinely using, installing, maintaining and servicing this heat pump are strongly encouraged to read this
entire manual. If uncertain about any instructions given herein, AquaCal Customer Support (800-786-7751) should
be contacted for additional information.
How to Operate the Controls - Pool or Spa
1. Turn the selected pool or spa thermostat dial clockwise to its highest setting.
2. The heat pump will start and begin to heat the pool or spa.
NOTE: The heat pump has a time delay so if it shuts down for any reason, it will not
restart for approximately five (5) minutes.
3. The typical spa may take several hours to initially heat up, while a pool may take several days. Heating
time will depend on the volume of water, water temperature, and the climatic conditions at the time of
start-up. (Also see Calculating Initial Heating Time.)
4. When the pool or spa reaches the desired temperature, slowly rotate the thermostat knob
counterclockwise until the heat pump (just) stops. The thermostat is now set to automatically
maintain this temperature.
QUICK START& STOP
Manual Switching From Pool to Spa
NOTE: It is best to stop the pump while repositioning valves.
1. Open spa valves and close pool valves.
2. With the spa filter pump running for at least five minutes, move the POOL/OFF/SPA toggle switch
from the Pool Setting to the Spa Setting.
3. Turn the Spa thermostat clockwise until it stops (104 F).
4. The typical spa may take several hours to initially heat up. Heating time all depends on the volume of
water, water temperature and the climatic conditions at the time of start-up.
5. When the spa reaches the desired temperature (104 F is maximum), slowly rotate the thermostat
knob counterclockwise until the heat pump (just) stops. The spa thermostat is now set to
automatically maintain this temperature any time the spa thermostat has been selected.
Start Up
1. Set pump controls to allow for temporary, continuous operation.
2. With pump OFF, position water valves to heat the POOL or SPA.
3. Rotate both thermostats counterclockwise to lowest temperature setting.
4. Depending on valve settings (per #2, above), position the POOL/OFF/SPA toggle switch to point at
either the POOL or SPA thermostat knob.
5. Ensure power is supplied to the heater, then start the water pump; the POWER and FLOW lights
should now both be lit. Permit the water pump to operate for five (5) minutes before proceeding
To Stop the Heat Pump
The unit can be stopped by switching off the electrical supply or by setting the desired temperature lower
than the actual water temperature.
Time Clock Programming
Once the heat pump has brought the pool or spa up to temperature, it will be necessary to reset the pump
controls. Be sure to allow enough running time for the heat pump to replace lost heat. This time will vary
depending upon the time of year. Colder months require longer running times—usually eight to twelve hours.

9
PHYSICAL CHARACTERISTICS
& PERFORMANCE
1. ALL DIMENSIONS IN INCHES
2. MIN. CLEARANCE 24" FROM
AIR COIL
B
DATA PLATE
INFORMATION
B
REAR VIEW
JK
H
POWER
OPTIONS
BONDING
LUG
NOTES:
G
F
E
D
C
AIR COIL
A
CONTROL BOX
ACCESS PANEL
COMPRESSOR
ACCESS PANEL
A
Dimensional Information - TropiCal Models
T65 and T115

10
Dimensional Information - TropiCal
Model T135
B
DATA PLATE
INFORMATION
B
A
CONTROL BOX
ACCESS PANEL
COMPRESSOR
ACCESS PANEL
1. ALL DIMENSIONS IN INCHES
2. MIN. CLEARANCE 24" FROM
AIR COIL
NOTES:
BONDING LUG
OPTIONS
POWER
H
K
J
E
D
A

11
Refrigerant Circuit Performance Charts
Use of Charts- Information for the Technician:
The charts are intended for use by trained and qualified air-conditioning and refrigeration technicians only.
The charts are compiled specifically for evaluation and diagnostic purposes, and are NOT designed for use
as charging charts. To apply the chart data to actual conditions: gather the operating pressures, suction tube
superheat & liquid line subcooling values, water temperature change through the heater, and the total unit
amps. Locate a chart that most closely represents current actual conditions. Readings obtained that differ
from the charts in excess of 10% (+ or -), may indicate a problem within the mechanical refrigeration
system. Reference: Troubleshooting Refrigerant Circuit Problems, following the charts. Some interpolation
between charts will be necessary should actual conditions not align reasonably well with the charts. Should
refrigerant circuit readings appear normal, but not the Water DTvalue, the likely cause will be water flow
above or below 45 GPM. (TropiCal refrigerant circuits will perform acceptably with condenser water flow
between 20 to 70 GPM.)
Performance Charts Follow
TropiCal: Table of Specifications

MODELS: T65”X”-A T65”X”-B T115 “X”-A T115 “X”-B T135 “X”-A T135 “X”-B
BTU - 80%RH
Air ºF / Air ºF… 80/50 55000/37000 55000/37000 104,000/70,000 104,000/70,000 126,000/82000 126,000/82000
COP 4.8/3.7 4.8/3.7 4.3/3.2 4.3/3.2 5.7/4.0 5.7/4.0
BTU - 63% RH
Air ºF / Air ºF… 80/50 51000/34000 51000/34000 97,000/65,000 97,000/65,000 119000/77000 119000/77000
COP 4.5/3.6 4.5/3.6 4/3.1 4/3.1 5.4/3.8 5.4/3.8
Kilowatt Input (80% RH) 3.4 3.4 7.1 7.1 6.5 6.5
Voltage/Hz/Phase 208-230/60/1 208-230/60/3
208-230/60/1 208-230/60/3 208-230/60/1 208-230/60/3
Min. Circuit Ampacity 20.01
14.04 40.56 26.14 37.36 30.14
Recommended Fuse Size
20 15.00 40 30 40 35
Max. Fuse or Breaker Size
30 20.00 70 40 60 50
Min-Max Water Flow (gpm)
20-70 20-70 20-70 20-70 20-70 20-70
Shipping weight (lbs) 250 250 270 270 300 300
Shipping Size (l x w x h) 36" X 30" X 35" 36" X 30" X 35" 36" X 30" X 35" 36" X 30" X 35" 36"X30"X42 36"X30"X42
Uncrated Weight (lbs) 223 223 243 243 273 273






12
Refrigerant Circuit Performance Charts
For use with Troubleshooting Refrigerant Circuit Problems guide, following charts.
 !" #$


 











  ! 
!"#$#%$# &'( ( ) ' "* !"
"#$#%$# &+" (! + ( ,* !&
)"#$#%$# &+, +" " ) &, +
-./01

 !" #$


 











  ! 
!"#$#%$# &** '" ( ) "* &+
"#$#%$# &&& '( & &* ,, &(
)"#$#%$# &) +& ) " &( '
-./01

%& !" #$


 










  ! 
!"#$#%$# +( ,& " &" !, &)
"#$#%$# &, ,+ " &" !* &"
)"#$#%$# && "! ! &" ) "
-./01

$'($)*+" #$


 











  ! 
!"#$#%$# &* (* ( " "" &+
"#$#%$# &&' () & + ,' &+
)"#$#%$# &+ +' ' ) &+ '
-./01





13
NOTE: These guidelines are for use only by experienced, EPAcertified, HVAC technicians, and
were developed specifically for use with AquaCal heat pumps, and for use with Refrigerant Circuit
Performance Charts contained earlier in this manual.
Possible Conditions:
Unit Overcharged:
•Head pressure will be above normal;
•Suction pressure will be normal or slightly high (high, only if grossly overcharged);
•Unit amperage will be somewhat high;
•Liquid Sub-Cooling will be higher than normal;
•Superheat will be normal to low (low, only if grossly overcharged).
Explanation: Excess liquid refrigerant backs up in the condenser (into discharge line if grossly
overcharged). Elevated head pressure & high liquid sub-cooling, with near-normal suction pressure and
superheat, will be present. Unless grossly overcharged, the TXV will hold back the overcharge, maintaining
near normal suction pressure and superheat.
Unit Undercharged:
•Head pressure will be below normal;
•Suction pressure will be slightly low, to very low (depending on degree of undercharge);
•Amperage will be low;
•Liquid Sub-Cooling will be very low or nonexistent;
•Superheat will be higher than normal.
Explanation: A full column of liquid may not be consistently present at the TXV inlet. This condition results
in low suction pressure with higher than normal superheat. The liquid sub-cooling will be low, as will be the
head pressure.
TXV Stuck Closed:
•Head pressure will be excessive;
•Suction pressure will be lower than normal;
•Amperage will be high;
•Liquid Sub-Cooling will be higher than normal;
•Superheat will be higher than normal;
•Distributor lines may be frosted, iced, or very cold to touch.
Explanation: The flow of refrigerant is (mostly) stopped at the TXV. This results in a low suction reading
with high superheat. As liquid refrigerant “backs up” in the condenser, there is less room for high-pressure
vapor coming from the compressor. Therefore, head pressure increases above normal (TropiCal models do
not have sufficient space on the high-side to store the entire charge). With little refrigerant flowing, more
heat is being removed in the condenser than is being added at the evaporator- result: higher than normal
liquid sub-cooling.
Guide: Troubleshooting Refrigerant Circuit Problems
Refrigerant Circuit Service Only by Qualified, EPA Certified Technician
WARNING ! Failure to heed the following may result in permanent injury or
death.
Heater contains refrigerant under high pressure. Repairs to the refrigerant circuit must not be
attempted by untrained and/or unqualified individuals. Service must be performed only by qualified
HVAC technicians. Recover Refrigerant to relieve pressure before opening system.

14
TXV Stuck Open:
•Head pressure will be slightly to moderately low;
•Suction pressure will be slightly high to very high;
•Amperage (not a reliable indicator of this condition);
•Liquid Sub-Cooling will be lower than normal;
•Superheat will be minimal or nonexistent;
•Suction line, and possibly a large portion of compressor, will be very cold and possibly “sweating”.
Explanation: Refrigerant is flowing through the system too quickly; enough heat cannot be added in the
evaporator to boil off all the liquid refrigerant. The main effect is to flood the suction line and compressor
with liquid refrigerant. The primary indicator of this condition is little or no suction line superheat. Also, as
the TXV is not holding back the required amount of refrigerant, there may be flash gas (high-pressure
vapor) present in the liquid line; this is indicated by reduced liquid sub-cooling.
Insufficient Condenser Water Flow:
•Head pressure will moderately high to very high;
•Suction pressure my be normal to slightly high;
•Amperage will be higher than normal;
•Liquid Sub-Cooling will be absent; the liquid line will be very warm or even hot to touch. When combined
with high condenser water DT (see next bullet item), this condition is a prime indicator of insufficient
condenser water flow;
•Condenser entering-leaving water temperature difference (water DT) will be higher than normal… This
condition is a prime indicator of insufficient condenser water flow;
•Superheat will be high-normal to high.
Explanation: Heat is not being removed in the condenser in quantities sufficient to produce appreciable
amounts of liquid refrigerant. With no liquid seal occurring in the condenser, the liquid line–in essence–
becomes an extended discharge line. Keys to diagnosis: very warm to hot liquid line, and a high condenser
water Delta-T.
Placement of Heater
Every indoor installation is unique, therefore, there are no specific guidelines for this type of installation. For
assistance, please contact AquaCal’s Engineering or Technical department at [phone]; they will assist
you with your specific needs.
Outdoor Installation
Service and Operational Clearances:
Refer to recommended clearance drawings following this section. Allow 24" clearance between the heat
collection surfaces and walls, fences, shrubs, or other objects. The heat pump requires large volumes of air
moving over the heat collector.
Allow 5 feet of vertical clearance between the top of the heat pump and any roof overhang or
other obstruction. This clearance prevents cold discharge air from recirculating back into the evaporator
coils (recirculation would reduce the overall performance of the heat Pump).
Provide at least 30” open area in front of the main access panel. The electrical panel will need to
be accessed during installation and service, so avoid any plumbing obstructions that will restrict
easy access.
INSTALLATION
Indoor Installation
u
u
u

15
Typical Installation Clearances
Code Required Clearances:
In addition to the previously stated clearance requirements, follow all applicable local, state, and national
requirements relative to spacing from other objects or equipment.
u
24 - Inches
(Side)
24 - Inches
(Rear)
24 - Inches
(Side)
30 - Inches
(Front)
Front, Side and Rear
Rain run-off
must be
directed away
from unit
Overhang
with gutter
5 ft. minimum
clearance,
overhead
2 ft. minimum
clearance, rear
30” minimum
clearance, front
(No Scale)
Front, Rear, and Overhead
Equipment Pad Requirements
The equipment pad should be constructed to provide adequate drainage and support to the base of the heat
pump (see Table below). The pad should be essentially level with just enough pitch to drain condensate and
any other water away from the heater.
Anchoring Heater to Pad
Follow all relevant local, state, or national requirements regarding wind load anchoring (use huricane anchoring
kit, part #STK0010). As necessary, contact AquaCal Technical Support, 800-786-7751, for assistance in
determining best method of compliance.
Irrigation, Rainwater Runoff, and Landscape Features
Place the heat pump away from rain runoff from the roof. A gutter or rain shield may be required on the roof
edge above the heat pump.
Relocate or adjust irrigation to avoid water spray directly onto the heat pump. Do not locate plant shrubs or
bushes directly adjacent to heat pumps. Doing so will prevent proper air circulation into the unit, and may inhibit
access to the heater when service is needed. Consult drawings above for proper clearances.
Model Minimum Pad Size
T135
T115
T65
36” X 42”
36” X 42”
36” X 42”

16
Plumbing Requirements
Overview:
When planning plumbing system layout, reference the plumbing schematics following this section as a guide to the
sequence of equipment, valves, fittings, etc. The plumbing configurations for typical installations are diagrammed.
In operation, it is imperative the heat pump receive water flow within the minimum-maximum ranges specified for
the particular heat pump. Should the system installation under consideration not closely match any of the schematics,
contact AquaCal Technical Support for advice and guidance: [phone].
Minimum/Maximum Water Flow Rates:
All TropiCal models are designed to operate successfully between flow rates of 20 to 70 gallons-per-minute
(GPM) . Design the plumbing system to maintain at least 20 GPM flow through the heater; the heat pump will not
operate correctly, nor reliably, with less than 20 GPM of water flow supplied. If water flow rates through the
heater will exceed 70 GPM, a spring-check bypass valve will be required; generally speaking, most residential
pools and spas will not require a bypass unless a pump of 2 HP or larger is used (for bypass valve details, see
information and plumbing schematic, following).
External Bypass Check Valve Requirement
For installations where flow rates exceed 70 gpm an additional spring bypass check valve must be installed.
NOTE:
Use of the wrong size check valve may compromise the heat pump’s efficiency, reliability, and may
void the factory warranty. For models T135, T115 & T65, a 5 lb. Spring check valve is required.
(AquaCal Part #2556.)
Parts and Materials:
Industry technology changes much too rapidly for AquaCal to specify, with exactness, any items outside and
beyond the heat pump. What is specified is that the heat pump must be installed in accordance with all applicable
local, state, or national codes & standards.
Connection to Heat Pump:
All TropiCal heat pumps come equipped with 2" PVC, plumbing unions. Connection to site plumbing is made via
PVC solvent cement to the female slip socket of the plumbing unions.
Ability to Winterize:
In regions where hard winters are typical, the unions mentioned above allow for easy disconnection/reconnecting
of the heater from the plumbing system. Caution: do not defeat the function of the unions–use no glue on the
threaded portion of the unions.
Maximum Operating Pressure: 50 PSI
Bypass Check

17
Plumbing Schematics

18
Water IN & OUT Connections
For proper operation and maximum efficiency, piping coming from the pump and filter MUST be connected to the
"IN" port of the heater. Likewise, connect piping returning to the pool/spa to the "OUT" port of the heater. See
drawing below.
WARNING! Failure to heed the following may result in permanent injury
or death.
Installation made by unqualified persons can result in hazards to the installer and others. The information
contained in this Electrical Installation section is intended for use by qualified electrical installation technicians,
familiar with electrical service industry safety standards and methods. Electrical installation to be performed
by qualified individuals only.
Electrical Requirements
General Information:
uWhen possible, locate the equipment disconnect means within arm's reach of the heater's
electrical enclosure or as close as possible to the heater. Always satisfy applicable codes and
standards.
uAll AquaCal heat pumps are designed for copper conductors, only. In sizing power wiring, be
especially aware of up-sizing requirements required due to wiring distances. Always satisfy
applicable codes and standards.
uMultiple heaters installed at same site generally require special sequencing controls (AquaCal part
#ASC-(number of heaters)); if yours is a multi-heater installation, contact AquaCal Technical Support
for assistance (800-786-7751).
uElectrical installation should be by licensed electrician only.
uConnecting External Controllers: See document entitled “Connecting External Controllers to
AquaCal Heat Pumps”. These instructions are shipped inside heater accompanying the electrical
schematic.

19
Code Requirements:
uThe electrical installation must conform to the most current version of the National
Electrical Code, NFPA No. 70, and all applicable local and state codes.
uNational Electrical Code, article 680; Swimming Pools, Fountains, and Similar Installations, shall
apply.
uNational Electrical Code, article 440, Air-Conditioning and Refrigeration Equipment, shall apply.
Reference Equipment Data Plate:
uAll TropiCal heat pumps have their data plates located on the left, exterior, side panel.
Refer to equipment data plate for unit-specific electrical power and over-current protection
requirements. Based on data plate information; size wiring, devices, and over-current
protection per applicable codes and standards.
uSee drawing below for data plate details specific to Electrical Installation Requirements. The
numbered areas represented below will contain the necessary information required in sizing
electrical service and over current protection devices.
MADE IN THE USA
PHASE
MAXIMUM TIME DELAY FUSE OR HVAC BREAKER
L.R.A.
FAN MOTOR Vac
REFRIGERANT: Factory charged R-22 Only
Tested to 500 psig High side/150 psig Low side INDOOR/OUTDOOR USE
AQUA CAL, INC
A TEAM HORNER COMPANY
2737 24TH STREET NORTH
ST. PETERSBURG, FL 33713
FACTORY SERVICE
1-800-786-7751


         
ETL LISTED
          
         
         
              

MANUFACTURING CODE
SERIAL NO.
BAR CODE
#1 #2
#3 #4
#5
#6 #7
#8
MINIMUM CIRCUITAMPACITY HZ
ELEC. SERVICE: Vac.~
COMPRESSOR Vac R.L.A
F.L.A.
H.P.
oz/Kg

20
1. POOLTEMPERATURE CONTROL - Set this knob for desired pool water temperature
2. POOL/OFF/SPA -Toggles between pool temperature/off/spa temperature
3. SPA TEMPERATURE CONTROL - Set this knob for desired spa water temperature
4. POWER LIGHT - Indicates electrical power is supplied to the heater
5. FLOW LIGHT - Indicates water pressure (Flow) is present at the heater
6. DEFROST LIGHT - Indicates heater is in the defrost mode
T135/115/65 Control Panel Layout
Getting Familiar with Controls
START-UP & OPERATION