Aquaglide Jungle Joe 2 User manual

Contents:
Jungle Joe 2 – (1) Jungle Joe 2 tube, (1) Repair Kit
Watersports Safety Code
Watersports are fun and challenging but involve inherent risks of
injury or death. To increase your enjoyment of the sport and to
reduce your risks, use common sense and follow these rules:
Before you start:
• Familiarize yourself with all applicable federal, state, and local laws, the risks
inherent in the sport, and the proper use of the equipment.
• Know the waterways.
• Use caution and common sense.
• Do not use in recreational swimming pools; within 3,0m (10ft.) of commercial
pool edge, or within 4,5m (15ft.) of boats, docks, or other hard obstructions.
• Do not attempt or allow somersaults. Landing on the head or neck can
cause serious injury, paralysis or death.
• Never use at night, or in low-light conditions.
• Never use in poor weather conditions, excessive wind, waves or lightning.
• Do not use on dry land.
• Do no use without proper anchoring.
• Never swim under the product.
• Take extreme care when swimming between the shore and the product. Be
cautious of any boat trafc or other obstructions. Ensure all users are capable
swimmers and are not excessively fatigued. Do not allow anyone to attempt to
swim to or from the product that are not physically able to do so.
• Always ensure that the swimming area around the product is free of
submerged logs, rocks and sandbars. Ask about the local water conditiions
before use.
• Only allow use of the product with proper supervision. Secure the product
when not in use to prevent access by any other users.
• Do not jump or dive from this item.
• Do not jump onto this item from any other item.
• Do not use in water where there are sharks or other animals that could pose a
threat to humans.
• If product is used indoors, always ensure adequate ceiling height overhead.
• Always remove personal items such as rings, watches or other sharp objects
before use.
Your Equipment:
• Check all equipment prior to use. Inspect your product for missing, defective
or worn parts. Never use the product if excessive wear or damage are detected.
• Always check for proper ination before each use. Temperature and environ-
mental changes can cause changes in tube pressure. Using the product over
or under inated is dangerous and can cause damage to the product, voiding
the warranty.
• Always check security of the anchor(s) and all attachments before each use.
• Always wear a life vest (PFD) approved by the authorities in area of use.
THE WARNINGS AND PRACTICES SET FORTH ABOVE IN THE WATER-
SPORTS SAFETY CODE REPRESENT SOME COMMON RISKS
ENCOUNTERED BY USERS. THE CODE DOES NOT PURPORT TO COVER
ALL INSTANCES OF RISK OR DANGER. PLEASE USE COMMON SENSE
AND GOOD JUDGMENT.
Please contact us if you have any questions on the proper selection,
function, or safe use of this product.
Manual covers the
following products
Jungle Joe 2
Maximum
number of
users
Ten (10)
Maximum
Suggested
Weight Load
2000 lbs. (907 kg)
www.Aquaglide.com
Aquaglide, Inc. #1 North Shore Dr, SE White Salmon, WA 98672 TEL: (509) 493-4938 FAX: (509) 493-4966
USE OF THIS PRODUCT AND PARTICIPATION IN WATERSPORTS
INVOLVES INHERENT RISKS OF INJURY OR DEATH.
• This product should never be used by children except under adult supervision.
• Not intended for use by children under 5 years of age.
• This product is not a personal fl otation device.
• Always wear a fl oatation vest (PFD) as required by the authorities in area of use.
• Never place wrists or feet through handles.
• Do not use in shallow water (less than 9 ft [2,78 m] deep).
• Do not use within 15ft (4,5 m) of shore, docks, pilings or other hard objects.
• Never swim under this product.
• Do not jump or dive from this product.
• Do not exceed the manufacturer’s recommended number of users for
this particular product.
• Do not use while under the infl uence of alcohol or drugs.
• Read Operator’s Manual before use.
Made in China
TO REDUCE THE RISK OF INJURY OR DEATH,
FOLLOW THESE GUIDELINES:
• Do not jump or dive from the product.
• Do not stand on the top of the product.
• Do not swim, stand or climb below other climbers.
• Make sure that swimmers have cleared the entry zone before entering water.
• Do not exceed product weight capacity of 1000lbs (454 kg).
• Do not concentrate more than 300 lbs. (136 kg) in any one area.
• Do not use without adequate air pressure - 1.6 p.s.i. minimum (0,110 bar)
THE WARNINGS AND PRACTICES SET FORTH ABOVE REPRESENT SOME COMMON RISKS
ENCOUNTERED BY USERS AND DOES NOT PURPORT TO COVER ALL INSTANCES OF RISK
OR DANGER. PLEASE USE COMMON SENSE AND GOOD JUDGMENT.
Owner’s Manual
Stop! Read this manual carefully
before using this product!
It is the owner’s responsibility
to read the owner’s manual
and instruct all users in the safe operation of these products. By inat-
ing these products you hereby agree to the Release of Liability, Claim
Waiver, and Assumption of Risk Agreement in this manual. Please read
this manual prior to inating and using these products and keep for
future reference. As with any action sport, recklessness, inexperience,
misuse, or neglect of the equipment may result in serious injury or
death.

AQUAGLIDE, INC.
WHITE SALMON, WA - U.S.A.
STANDARDS: EN 15649: 2012, W.A.S.
PRODUCT: JUNGLE JOE 2
MADE IN P.R.C.
DESIGNED IN U.S.A.
122cm
213cm
2,78m (9ft)
10 10
4,5m
(15ft)
0 - 4
0,138bar
(2.0psi)
max.
907kg
(2000lbs)

No protection against drowning!
Keine Schutz gegen Ertrinken!
Pas de protection contre la noayada!
No protege contra el ahogamiento!
Nessuna protezione contro l’aogamento!
Beschermt niet tegen verdrinken!
Only for swimmers!
Nur für schwimmer!
Seulement pour les nageurs!
Sólo para nadadores!
Solo per i nuotatori!
Alleen voor zwemmers!
Aquaglide, Inc.
#1 North Shore Dr SE
White Salmon, WA 98672
USA
Compliant with
DIN EN-15649: 2012
Prolonged exposure to salt water candamage and/orshorten the expected lifetime of
thisproduct. The marine environment includesmany damaging elements including
corrosion, abrasion and damage from marine life such as barnacles. Regular cleaning
and rinsing with fresh water can reduce these risks. APVC-safe antifouling paint should
be used to help protect this product against marine growth. DAMAGE CAUSED BY
EXPOSURETO SALTWATER IS NOT COVERED BY WARRANTY.
L: 658 cm (259”)
W: 547 cm (180”)
H: 376 cm (148”)

Assembly
1) Locate a at, dry area with access to electrical outlet or extension cord. The
best setup position will also make launching easy, so ideally the Jungle Joe tube
should be carefully carried into position at the water’s edge. NOTE: Dragging
or sliding the Jungle Joe over ground either before or after ination can cause
damage.
2) Once in the setup/ launch position, unfold the Jungle Joe completely and
locate the Main Valve. The Main Valve is located on the lower, blue section of
the product. See diagram for details.
3) Using a high output pump capable of reaching 1.6 psi (minimum), place the
ination hose with proper adaptor into the Main Valve to inate the main, blue
section of Jungle Joe. Inate to 2.0 psi (0,138 bar). Check for proper air pres-
sure using a manometer. After ination, replace Main valve cover. Ination times
can vary by inator, but the Jungle Joe should be rm and tight when completely
inated.
DO NOT OVER-FILL. Excessively high pressure can cause damage to the
product and may void the warranty. Carefully monitor air pressure in the product
especially during hot weather.
WARNING: Do not use an air compressor to inate tube. Air compressors are
designed for high pressure ination and can cause tube to burst if over-inated.
WARNING: Do not use Jungle Joe without adequate air pressure - 1.6 p.s.i.
(0,110 bar) minimum in the main bladder.
4) Next locate the Upper Valve found on the white upper tube near the main
valve. Follow the instructions and warnings found in Step #3 to properly inate the
Upper section. Inate to 2.0 psi (0,138 bar). Check for proper air pressure using
a manometer.
WARNING: Do not use Jungle Joe without adequate air pressure - 1.6 p.s.i.
(0,110 bar) minimum in the upper bladder.
5) Next locate the Slide Valve found on the slide’s blue sidewall. Follow the
instructions and warnings found in Step #3 to properly inate the Slide. Inate to
1.2 psi (0,083 bar).
6) Depending on the application, some users may have purchased an optional
Swimstep or Runway boarding platform. If you have a boarding platform, connect
it now using the instructions provided with the accessory. NOTE: It is best to
attach such items while they are deated. Once fully attached with Interloc straps,
then inate.
7) To launch the product, make sure to have at least 6 people evenly spaced
around the product to help carry it. NEVER DRAG THE PRODUCT! YOU MUST
LIFT AND SET TO AVOID ANY ACCIDENTAL TEARING AND/OR ABRASION.
www.Aquaglide.com
Aquaglide, Inc. #1 North Shore Dr, SE White Salmon, WA 98672 TEL: (509) 493-4938 FAX: (509) 493-4966
Anchoring
IMPORTANT: Proper anchoring is essential to the safety and performance of
your product. Due to the wide variety of conditions, we advise using a profes-
sional skilled in mooring and anchoring, and experienced with local conditions.
If improperly anchored, the product can move and/or oat away. Aquaglide, Inc.
is not responsible for any damage, injuries or losses due to improper anchoring.
NOTE: There are 4 heavy duty anchor rings underneath the Jungle Joe. These
rings are located underneath the Main section, near each of the 4 corners.
Due to the high loads that may be generated, you must use AT LEAST 2 of
these rings to spread the load and properly secure the product under normal
conditions.
Main Valve
Upper Valve
Slide Valve
Watersports can be safe and fun for all levels of enthusiasts. The Operator’s Manual is presented to enhance
your enjoyment of the sport. It is intended to alert you to some of the potentially dangerous conditions that
can arise in all watersports. It is the owner’s responsibility to read the owner’s manual and instruct all users
in the safe operation of these products. By inating these products you hereby agree to the Release of
Liability, Claim Waiver, and Assumption of Risk Agreement in the Owner’s Manual.
To reduce the risk of injury or death, follow these guidelines:
• Carefully read the product Owner’s Manual and follow the instructions.
• Take all reasonable precautions in the use and operation of your trampoline and/or aquapark.
• Teach anyone using your trampoline and/or aquapark about safe guidelines prior to use.
• Know your own limits. Stop when you are tired. Act responsibly. Be in good physical
condition and be cautious in your use of this or any other water sports product.
• Periodically check mooring bridles and/or lines to ensure safety. Replace any portion of
mooring and/or connection system that shows signs of wear.
• Do not add any hardware or attachments not otherwise supplied by the manufacturer.
THE WARNINGS AND PRACTICES SET FORTH ABOVE REPRESENT SOME COMMON RISKS
ENCOUNTERED BY USERS AND DOES NOT PURPORT TO COVER ALL INSTANCES OF RISK OR DANGER.
PLEASE USE COMMON SENSE AND GOOD JUDGMENT.
Please contact the dealer or manufacturer of this product if you have any questions about proper selection,
function, or safe use of this product. Made in China
CAUTION
Owner’s Manual

www.Aquaglide.com
We strongly recommend using our optional 2-Way Heavy Duty Mooring Bridles,
not included.
Here are some general guidelines for anchoring your product. These guidelines
are not intended to replace the need for professional installation.
1) Choose a location for your Jungle Joe and/or aquapark. Place the product
in at least 9 ft. (2,78m) of water depth and in an area protected from the wind
and boat trafc. Review your lake rules and restrictions with your local authori-
ties.
2) Carefully check the water and seabed below the selected area for sharp or
dangerous objects (i.e. rocks or stumps).
3) Keep a safe distance from docks, boats, boat lifts, and any other structures.
DO NOT tie the product to a dock!
4) Anchors and anchor chain are sold separately. We recommend a MINIMUM
of 400 lbs. for short-term anchoring of the Jungle Joe in settled conditions.
Heavier and/ or multiple moorings (1000 lbs. or more) should be used with
Aquaparks or on large, windy bodies of water. Professionally installed ground
screws are also acceptable.
5) Attach anchor chain securely to the anchor. Use a buoy tied to the other end
of the chain to easily locate your anchor.
6) When the product is in place, remove the buoy and shackle the anchor chain
to the anchor rings underneath the product. BE SURE TO ALLOW enough
slack in the anchor chain to allow the product to move in wind or waves without
displacing your mooring.
7) If strong winds or storms are expected, it is best to remove the product from
the water and secure and/or deate it.
Operation
1) This item is a climbing structure and water slide. Users climb up various
climbing walls and slide down the slide face in sitting position. Users may also
enter the interior portion of the item from various openings. Interior area is
designed for splashing in shallow water. This item must be used with at least
one Aquaglide boarding platform.
2) When connecting multiple items, use only Aquaglide Vario-Lock cinch straps
and connecting rings according to the instructions provided. Make sure that
the connection is tight and that there is NO GAP greater than 25mm (~3/4”)
between items. IMPORTANT: Failure to connect these items properly may
result in injury or death.
3) We strongly recommend maintaining supervision at all times during use by
a professionally certied lifeguard. NEVER use unattended.
4) Do not exceed the product’s recommended number of users or capacity.
5) USE COMMON SENSE. Never jump or dive from the product. Do not
allow anyone to stand on the top of the product because motion could cause a
loss of balance and injury.
6) Do not swim, stand or climb below any other climbers. Ensure that all
swimmers have cleared the area before entering the water. Never swim under-
neath the product.
7) The maximum weight capacity is 2000 lbs. (900 Kg). It is acceptable to have
up to ten people on the product.
IMPORTANT:
• Do not exceed product weight capacity of 2000lbs. (907 kg)
• Do not concentrate more than 300 lbs. (136 kg) in any one area.
• Do not use without adequate air pressure - 1.6 p.s.i. (0,110 bar)
minimum in the main and upper bladders.
8) If the product shows any signs of instability or appears to have lost air pres-
sure, immediately discontinue use. Check and monitor moorings, air pressure
and air-holding ability. Do not continue use until these are conrmed.
Care and Maintenance
1) While your product has been initially treated with UV protectant, long-term
exposure to sunlight will damage the product. Regularly apply a UV protectant
to the exposed surface of the tube to ensure the life of your product. We recom-
mend using ONLY INDIKON UV Protectant intended for use on vinyl for this
purpose. Monthly application while the product is in use is required. NOT DO-
ING THIS WILL VOID THE WARRANTY. INDIKON UV Protectant is available
at most watersports dealers, or online at www.aquaglide.com
2) WARNING: Certain products, especially petrolium-based solvents, cleaners
and protectants such as ArmorAll can damage the product and use of these
products will void the warranty.
3) WARNING: Use of a high-pressure washer will damage the product and
void the warranty. To clean, use a soft bristle brush with mild soap and fresh
water. INDIKON UV Protectant contains a ‘safe for vinyl’ cleaner, and can be
used to clean and protect the product at the same time.
4) Check the ination of your tube often. Check for proper air pressure using a
manometer. It may appear to have lost air early in the morning, but will expand
once the sun warms it. Maximum expansion will occur in the heat of the day.
Proper ination is critical to the safe operation of your product and will prolong
damage from wear.
Storage
1) Before storing, place the product on a clean, level area. Clean with mild soap
and water and allow to dry completely. Apply INDIKON Protectant to the surface
of the PRODUCT before deating.
2) Remove all attachments and store in a sealed water-proof container (i.e. a
plastic covered box or bin).
3) Remove ALL of the air from the tube using the deation end of the high
output inator/deator. If some air is left in the tube, it may freeze causing
cracking.
4) Fold the deated tube in thirds then roll loosely.
5) Store the product out of direct sunlight and protected from the environment
in a clean, dry location. It is best to store inside a container with moth balls to
prevent damage from rodents. NEVER store uncovered, in a damp location, or
on a concrete surface! NEVER store at temperatures below 40 degrees F.
Aquaglide, Inc. #1 North Shore Dr, SE White Salmon, WA 98672 TEL: (509) 493-4938 FAX: (509) 493-4966
Table of contents
Other Aquaglide Accessories manuals

Aquaglide
Aquaglide Cyclone User manual

Aquaglide
Aquaglide SuperTramp 14 User manual

Aquaglide
Aquaglide Escalade 2m User manual

Aquaglide
Aquaglide PLATINUM Performance Revolution Rock-N-Slide User manual

Aquaglide
Aquaglide Runway Platinum User manual

Aquaglide
Aquaglide Rockit JR User manual

Aquaglide
Aquaglide Spitfire 60 User manual

Aquaglide
Aquaglide SuperTramp 14 User manual

Aquaglide
Aquaglide TANGO User manual

Aquaglide
Aquaglide Splashmat User manual