ARA PY500AC User manual

Sliding Gate Operator
User's Manual
PY
PY
PY
PY 5
5
5
5 00
00
00
00 A
A
A
A C
C
C
C

PY500AC SLIDING GATE OPERATOR
1
OUTLINE
1. Products introduction …………………………………… 2
2. Important safety precautions …………………………… 2
3. Main technical parameters …………………………… 2
4. Mechanical Installation ………………………………… 2
5. Adjustment ……………………………………………… 5
6. Wire Connecting ………………………………………… 6
7. Turning and operation …………………………………… 8
8. Programming Process …………………………………… 10
9. Maintenance …………………………………………… 1 4
10. Trouble Shooting ………………………………………… 1 4
1 1 . Packing list …………………………………………… 1 4

PY500AC SLIDING GATE OPERATOR
2
1.
1.
1.
1. Products
Products
Products
Products introduction
introduction
introduction
introduction
please
please
please
please read
read
read
read the
the
the
the instructions
instructions
instructions
instructions carefully
carefully
carefully
carefully before
before
before
before proceeding.
proceeding.
proceeding.
proceeding.
MCU
MCU
MCU
MCU is
is
is
is supplied
supplied
supplied
supplied to
to
to
to control
control
control
control the
the
the
the gate
gate
gate
gate operator.
operator.
operator.
operator.
Keypad
Keypad
Keypad
Keypad /
/
/
/ single
single
single
single button
button
button
button interface.
interface.
interface.
interface.
P
P
P
P hoto
hoto
hoto
hoto beam
beam
beam
beam safety
safety
safety
safety beam
beam
beam
beam interface.
interface.
interface.
interface.
User
User
User
User can
can
can
can select
select
select
select Auto-close
Auto-close
Auto-close
Auto-close function.
function.
function.
function.
Manual
Manual
Manual
Manual key
key
key
key release
release
release
release design
design
design
design for
for
for
for emergency
emergency
emergency
emergency purposes.
purposes.
purposes.
purposes.
Gate
Gate
Gate
Gate operator
operator
operator
operator has
has
has
has a
a
a
a uto
uto
uto
uto -reverse
-reverse
-reverse
-reverse function,
function,
function,
function, and
and
and
and the
the
the
the reverse
reverse
reverse
reverse power
power
power
power can
can
can
can change
change
change
change by
by
by
by user.
user.
user.
user.
2.
2.
2.
2. Important
Important
Important
Important safety
safety
safety
safety information
information
information
information
Carefully read and follow all safety precaution s and warning before attempting to install and use this
automatic gate operator.
Make
Make
Make
Make sure
sure
sure
sure the
the
the
the Power
Power
Power
Power supply(AC220V
supply(AC220V
supply(AC220V
supply(AC220V or
or
or
or AC110V)
AC110V)
AC110V)
AC110V) of
of
of
of the
the
the
the gate
gate
gate
gate operator
operator
operator
operator is
is
is
is suitable
suitable
suitable
suitable for
for
for
for the
the
the
the power
power
power
power
supply
supply
supply
supply in
in
in
in your
your
your
your area.
area.
area.
area.
3.
3.
3.
3. Main
Main
Main
Main technical
technical
technical
technical parameters
parameters
parameters
parameters
4.
4.
4.
4. Mechanical
Mechanical
Mechanical
Mechanical Installation
Installation
Installation
Installation
The PY500AC will handle gate weighting up to 500kg and up to 12m if the proper installation procedures
have been followed .
The PY500AC g ate o pe rator operates by forcing a drive rack by a drive gear. The entire configuration
Type
PY500AC
PY500ACU
Power supply
220V , 50Hz
11 0V , 6 0Hz
Motor speed
42rpm
47rpm
Rated output power of motor
150W
Remote control o perating distance
30m (F requency: 433.92 mHz)
Remote control mode
Single button
Output shaft height
58.5mm
Max. gate weight
500Kg
Output torque
1 4 N ·m
Limit switch
Spring limit switch
Noise
≤60 dB
Duty cycle
S 2, 15 minutes
extra remote control
100
Environmental temperature
- 2 0 ° C~ + 5 0 ° C
Gate Move speed
12m/min

PY500AC SLIDING GATE OPERATOR
3
is shown in the diagram below . The gate operator must be installed on the inside of the gate.
Sliding gate
Gate operator
Rack
Switch
Input power
Wall
Fig.1
Gate preparation
Be sure the gate is properly installed and slides smoothly before installing the PY500AC sliding gate
operator. The gate must be plumb, level, and move freely.
Conduit
In order to protect the cable , use PVC conduit for low voltage power cable and control wires. Conduit
must be pre set into the concrete when it is poured. Wires within the conduit shall be located or protected
so that no damage can result from contact with any rough or sharp part.
Concrete p ad
The base unit of the gate operator requires a concrete pad in order to maintain proper stability. The
concrete pad should be approximately 400 mm x 250 mm x 200 mm deep in order to provide for adequate
weight and structure to insure proper stable installation.
Anchors (see Fig.2)
You can use anchor bolts, anchors, washers and nuts. These anchors must be set into the concrete
when it is poured or y ou can use wedge anchors to fasten the operator.

PY500AC SLIDING GATE OPERATOR
4
Gate operator
Gear
Groundsill
Input power
Plain washer
Nut
Spring washer
Nut
Fig.2
Ope rator b ase (see Fig.3)
After the concrete has hardened, mount the gate ope rator base to the concrete pad. Verify that the base
is properly leveled.
U sing bolts and washers m ount the gate ope rator to the base and insert the cover . Check the operator
and make sure it is lined up with the gate.
Fig.3
Installation
Installation
Installation
Installation of
of
of
of Rack
Rack
Rack
Rack
�Fix the three nuts ( in the same package with rack) on the rack element.
�Lay the first piece of rack on the gear and weld the first nut on the gate.
�Move the gate manually, checking if the rack is resting on the gear, and weld the second and third nut .
�Bring another rack element near to the previous one. Move the gate manually and weld the three nuts
as the first rack, thus proceeding until the gate is fully covered.

PY500AC SLIDING GATE OPERATOR
5
�When the rack has been installed, to ensure it meshes correctly with the gear.
�The space between rack and gear is about 0.5mm .
Fig.4
Fig.4
Fig.4
Fig.4
5.
5.
5.
5. Adjustment
Adjustment
Adjustment
Adjustment
Spring limit switch
�To ensure safety, it is rec ommended to install limit switches at both ends of the gate to prevent the
gate from sliding out of the rails. The rails must be installed horizontally.
�Install the limit block as shown in Fig.4 and Fig.5. The spring limit switch and blocks are used to
control the position of the gate.
�Release the gear with the key and push the sliding gate manually to pre-determine the position, fix the
block to the rack and lock the gear by push up the release bar. Moving the gate electrically , a djust the
block to the proper position until the position of the opening and closing meet the requirement .
Rack
Sliding gate
Gear
Spring of limit switch
Limit block
197
300
Fig.5

PY500AC SLIDING GATE OPERATOR
6
M6X10
Fig.6
Manual operation
In case of power failure use key unlock the lock and pull down the release bar about 90 degree to open
or close gate manually, use the release key as follow:
�Fit the supplied key in the lock.
�Turn the key and pull down the release bar about 90 °to release the gear. (Note: Do not exceed 90 ° ,
be careful not to use too much force, otherwise the release bar will be damaged.)
�Open and close the gate manually.
Note: If the gate bumps the mounting post and cannot be electric opened, move the gate a few inches by
hand, thus you can release the gate with the key, open and close the gate manually.
Fig.7
6.
6.
6.
6. Wire
Wire
Wire
Wire Connecting
Connecting
Connecting
Connecting
Make sure that the power is OFF before making any electrical connections.
Remove the cover, perform the wiring ( See Fig.8 and wiring notes for control board) and replace the cover
again.

PY500AC SLIDING GATE OPERATOR
7
Fig.8
Wiring
Wiring
Wiring
Wiring notes
notes
notes
notes of
of
of
of control
control
control
control board
board
board
board
a. Power Input:E (Earth),L (Live),N (Neutral) .
PY500AC: AC2 2 0V
PY500ACU:AC110V
b. Caution light: connect caution light wire to LAMP(terminal X4)
PY500AC: AC2 2 0V
PY500ACU : AC110V
c. Output power supply: +12V (DC12V), COM (COM), I.R. (N.C Infrared )
If the infrared beam is interrupted during closing, the gate will reverse and open immediately. The
product is not factory equipped with an infrared device, the infrared output signal must be N.C.
GND
+12V
Out
I.R
COM
+12V
Terminal X2
Infrared Control board
Infrared with DC input
Signal
Fig.9
Fig.9
Fig.9
Fig.9 infrared
infrared
infrared
infrared Schematic diagram
d. Three-button switch / single-button switch (keypad ): The PY500AC is equipped with interfaces for
three-button switch and single-button switch (keypad).
To install the keypad attach one lead of your keypad to ‘ OSC ’ of terminal X1 and the other to the
‘ COM ’ . The keypad will function in single channel mode.

PY500AC SLIDING GATE OPERATOR
8
For three-button switch installation, use the terminals for multi-channel mode. Connect open wire of
external button switch to ‘ OPEN ’ of terminal X1, connect close wire of switch to ‘ CLOSE ’ , connect
stop wire of switch to ‘ STOP ’ , connect common wire of switch to ‘ COM ’ .
Common
Stop
Close
Open
Three-button switch
OPEN
CLOSE
STOP
COM
OSC
Keypad
OSC
COM
STOP
CLOSE
OPEN
Control board
terminal block
Control board
terminal blockSingle-button switch
terminal X1 terminal X1
Fig.10
Motor and capacitor ( Terminal X7, X6): V (com), U ( Positive direction ), W (O pposite d irection ), E
(grounding), C (capacitor)
Fi
Motor
W
Terminal X7
E
W
Control board
Terminal X6
CC
Capacitor
V
U
V
U
Fig.11
7.
7.
7.
7. Tuning
Tuning
Tuning
Tuning and
and
and
and operation
operation
operation
operation
Remote control
�The remote control works in a single channel mode. It has four buttons. See Fig.12 Remote
transmitter . The function of button 1, button 2, and button3 are the same. With each press of the
remote control button which has been programmed, the gate will close, stop, open or stop cycle.
Button 4 is available for pedestrian mode. Note: if you canceled the pedestrian mode, the function
of button 4 is same as the other three buttons.
�You can program/learn button 1, button 2, button 3 individually. You also can program/learn two
buttons or three buttons together, but you need repeat the program/learn process if you want to use
more than one button.

PY500AC SLIDING GATE OPERATOR
9
Button 1
Button 2
Button 3
Button 4
Fig.12 Remote transmitter
�Adding extra remote controls (Learn) : Remove the cover, p ress the learn button ‘ SW1 ’ (Fig.8) , the n
the ‘ LED 2 ’ (Fig.8) will be on and turn off, then press the remote control button which you want to use ,
the ‘ LED2 ’ will turn on about 2 seconds and then turn off again . The learning process is finished.
Up to 100 remote controls may be used.
�Erase remote controls : To erase all existing remote controls, press and hold learn button ‘ SW1 ’ , the
‘ LED2 ’ turns on, release the button once the ‘ LED2 ’ turns off . This indicates that all the remote
controls have been erased completely .
�Note
Note
Note
Note : Press the ‘ OPEN ’ button of external button switch or remote control button which has been
learned, the gate will open, the motor rotates clockwise, and the ‘ LED3 ’ and ‘ LED4 ’ is turns on. The
output voltage between ‘ LAMP ’ (terminal X4) is AC220V/110V, the voltage between ‘ V ’ and ‘ U ’ is
AC220V/110V. Press ‘ STOP ’ button or the same remote control button, the gate stops running. And the
‘ LED3 ’ and ‘ LED4 ’ is turns off. T hen press ‘ CLOSE ’ button or the same remote control button again, the
gate will close, the motor rotates anticlockwise, and the ‘ LED3 ’ and ‘ LED5 ’ is turns on. The output
voltage between ‘ LAMP ’ (terminal X4) is AC220V/110V, the voltage between ‘ V ’ and ‘ W ’ is
AC220V/110V. Press the ‘ STOP ’ button or the same remote control button, the gate stops running . And
the ‘ LED3 ’ and ‘ LED5 ’ is turns off.
�Verify open direction: If the gate does not move in the desired direction, then you will need to reverse
the motor operating direction, open the black plastic cover, you can do this by exchanging wires ‘ U ’ and
‘ W ’ , ‘ OPLT ’ and ‘ CLLT ’ .

PY500AC SLIDING GATE OPERATOR
10
8.
8.
8.
8. Porgramming
Porgramming
Porgramming
Porgramming Process
Process
Process
Process
Table of the DIP-switch (SW2)
� Set auto-close function: (This feature can be selected to make the gate stay open for some seconds
before it automatically closes. The auto-close time can be adjusted to between 0 and 44 seconds.):
T urn on the second and the third DIP- switch (See Fig.8) to ON position. Press the remote control
button (button 1, button 2 or button 3) that has been programmed to open the gate ( see V
V
V
V erify
erify
erify
erify open
open
open
open
direction
direction
direction
direction section). Stop the gate at any position by pressing the same button, wait a few seconds
according to your requirements (the range is 1~44 sec.), this period of time is regarded as ‘ auto-
close time ’ . Close the gate by pressing the same button. Press the button again to stop the gate or
the gate will stop automatically at its closed position if the limit switch is reached. After this setup is
complete, return DIP-switch 3 to OFF position immediately. Thus the auto-close
auto-close
auto-close
auto-close function
function
function
function has been
set.
� Cancel auto-close function: Turn on the second and the third DIP-switch (see Fig.8) to ON position.
Press the remote control button (button 1, button 2 or button 3) that has been programmed to open
the gate (see Verify
Verify
Verify
Verify open
open
open
open direction
direction
direction
direction section). Stop the gate at any position by pressing the same
button, wait until the gate close automatically (45 sec.). Press the same button to stop the gate or
the gate will stop automatically at its closed position if the limit switch is reached. After this setup is
complete, return DIP-switch 3 to OFF position immediately. Thus the auto-close function has been
canceled.
� P edestrian mode : Pedestrian mode can be used to open gate about 0.3~1.5 meters for people pass
Position
DIP-switch
Function SET
1
ON
Limit switch mode is NC.
OFF
Limit switch mode is NO.
2
ON
Auto-close function and auto-close function of pedestrian mode
are a vailable .
OFF
Both Auto-close function and auto-close function of pedestrian
mode are shut off.
3
ON
Programming / In this position the control board is in programming
condition, NOT USE condition.
OFF
Normal / In this position the control board can be normally used.

PY500AC SLIDING GATE OPERATOR
11
through.
Set width of pedestrian mode: T urn on the second and the third DIP- switch (See Fig.9) to ON position.
Press button 4 to open the gate ( see Verify
Verify
Verify
Verify open
open
open
open direction
direction
direction
direction section) , Wait until the gate travels the
distance according to your requirements ( the distance range is 0.3m~1.5m or wait for 3~10 sec.), it is
regarded as ‘ the width of pedestrian mode ’ . Then press the same button/button 4 to stop the gate,
wait for some seconds ( 1~ 44 sec.). C lose the gate by press ing the same button /button 4 . Press the
same button again to stop the gate or the gate will stop automatically at its closed position if the limit
switch is reached. After this setup is complete, return DIP-switch 3 to OFF position immediately. Thus
the width
width
width
width of
of
of
of pedestrian
pedestrian
pedestrian
pedestrian mode
mode
mode
mode has been set.
If you open the gate with button 4 , t he gate will stop at the expected position that you have set.
Set
Set
Set
Set auto-close
auto-close
auto-close
auto-close function
function
function
function of
of
of
of pedestrian
pedestrian
pedestrian
pedestrian mode:
mode:
mode:
mode: T urn on the second and the third DIP- switch (See
Fig.9) to ON position. Press button 4 to open the gate (see Verify
Verify
Verify
Verify open
open
open
open direction
direction
direction
direction section) , wait some
seconds (3~10 sec.). Then press the same button/button 4 to stop the gate, wait some seconds
according to your requirements (1~44 sec.), this period of time is regarded as ‘ auto-close time of
pedestrian mode ’ . C lose the gate by press ing the same button /button 4 . Press the same button again
to stop the gate or the gate will stop automatically at its closed position if the limit switch is reached.
After this setup is complete, return DIP-switch 3 to OFF position immediately. Thus the auto-close
auto-close
auto-close
auto-close
function
function
function
function of
of
of
of pedestrian
pedestrian
pedestrian
pedestrian mode
mode
mode
mode has been set.
Note: the new width of pedestrian mode has been re -programmed in the device and replaced the
original width you have set in Set
Set
Set
Set width
width
width
width of
of
of
of pedestrian
pedestrian
pedestrian
pedestrian mode
mode
mode
mode section.
If you open the gate with button 4, t he gate will stop at the new expected position that you have set,
after some seconds as what you have set, the gate will close automatically.
�Cancel width / auto-close function of pedestrian mode
Cancel both width and auto-close function of pedestrian mode: T urn on the second and the third DIP-
switch (See Fig.9) to ON position. Press button 4 to open the gate ( see Verify
Verify
Verify
Verify open
open
open
open direction
direction
direction
direction
section). Wait for more than 15 sec.. Then press the same button/button 4 to stop the gate. Wait until
the gate close automatically (45 sec.). Press the same button to stop the gate or the gate will stop
automatically at its closed position if the limit switch is reached. After this setup is complete, return
DIP-switch 3 to OFF position immediately. Thus the width and auto-close function of pedestrian mode
have been canceled.

PY500AC SLIDING GATE OPERATOR
12
Cancel width of pedestrian mode, keep auto-close function of pedestrian mode: T urn on the second
and the third DIP- switch (See Fig.9) to ON position. Press button 4 to open the gate ( see Verify
Verify
Verify
Verify open
open
open
open
direction
direction
direction
direction section). Wait for more than 15 sec.. Then press the same button/button 4 to stop the gate.
Wait some seconds according to your requirements ( 1~44 sec.). Then press the same button/button
4 to close the gate, press the same button again to stop the gate or the gate will stop automatically at
its closed position if the limit switch is reached. After this setup is complete, return DIP-switch 3 to
OFF position immediately. Thus the width of pedestrian mode has been canceled, t he auto-close
function of pedestrian mode has been reserved .
Note: the new auto-close time of pedestrian mode has been re -programmed in the device and
replaced the original auto-close time of pedestrian mode that you have been set in Set
Set
Set
Set auto-close
auto-close
auto-close
auto-close
function
function
function
function of
of
of
of pedestrian
pedestrian
pedestrian
pedestrian mode
mode
mode
mode section.
Keep width of pedestrian mode, cancel auto-close function of pedestrian mode :
:
:
:T urn on the second
and the third DIP- switch (See Fig.9) to ON position. Press button 4 to open the gate ( see Verify
Verify
Verify
Verify open
open
open
open
direction
direction
direction
direction section). Wait some seconds (3~10 sec.), then press the same button/button 4 to stop the
gate. Wait until the gate close automatically (45 sec.). Press the same button again to stop the gate
or the gate will stop automatically at its closed position if the limit switch is reached. After this setup is
complete, return DIP-switch 3 to OFF position immediately. Thus the width of pedestrian mode has
been reserved , t he auto-close function of pedestrian mode has been canceled .
Note: the new width of pedestrian mode has been re-programmed in the device and replaced the
original width.
If you open the gate with button 4 , t he gate will stop at the expected position that you have set, but
the gate will not close automatically.
�
�
�
�Turn on the second DIP-switch to OFF position (Factory preset: OFF position ), both auto close
function and auto-close function of pedestrian mode were shut off.
Note:
Note:
Note:
Note:
(1)
(1)
(1)
(1) You
You
You
You must
must
must
must follow
follow
follow
follow the
the
the
the operating
operating
operating
operating instruction
instruction
instruction
instruction as
as
as
as above,
above,
above,
above, any
any
any
any wrong
wrong
wrong
wrong operation
operation
operation
operation is
is
is
is not
not
not
not allowed
allowed
allowed
allowed during
during
during
during
setting.
setting.
setting.
setting. If
If
If
If your
your
your
your device
device
device
device responds
responds
responds
responds to
to
to
to your
your
your
your requested
requested
requested
requested function
function
function
function correctly,
correctly,
correctly,
correctly, you
you
you
you have
have
have
have set
set
set
set the
the
the
the
function
function
function
function successfully
successfully
successfully
successfully ,
,
,
, otherwise
otherwise
otherwise
otherwise repeat
repeat
repeat
repeat the
the
the
the above
above
above
above setup
setup
setup
setup instruction
instruction
instruction
instruction until
until
until
until your
your
your
your device
device
device
device
responds
responds
responds
responds to
to
to
to your
your
your
your expected
expected
expected
expected function.
function.
function.
function.
(2) If
If
If
If the
the
the
the gate
gate
gate
gate can
can
can
can not
not
not
not be
be
be
be moved,
moved,
moved,
moved, please
please
please
please check
check
check
check whether
whether
whether
whether the
the
the
the gate
gate
gate
gate is
is
is
is obstructed
obstructed
obstructed
obstructed or
or
or
or the
the
the
the gate
gate
gate
gate is
is
is
is too
too
too
too

PY500AC SLIDING GATE OPERATOR
13
weight.
weight.
weight.
weight.
� Adjustment of the auto-reverse function : rotate the ‘ W1 ’ knob ( Fig.8) by hand, the resistance may be
increased or decreased by rotating clockwise or counterclockwise. Note: if the gate fails to reverse in
the event of obstruction, then the opening force or closing force should be checked for conformity with
requirements and adjusted accordingly. The gate will reverse if obstructed when closing, and will stop
if jammed when opening.
�
�
�
�If the auto-reverse direction is wrong , p lease open the black plastic cover, exchange two wires ‘ U ’ and
‘ W ’ and Exchange wires ‘ O P LT ’ and ‘ CL LT ’ if the limit direction is wrong.
Activities
Activities
Activities
Activities Covered
Covered
Covered
Covered in
in
in
in this
this
this
this section
section
section
section
�Remote
Remote
Remote
Remote transmitter:
transmitter:
transmitter:
transmitter: With each press of the button, the gate will close, stop, open or stop cycle.
(
(
(
( Single
Single
Single
Single -button
-button
-button
-button mode)
mode)
mode)
mode)
�
�
�
�Three
Three
Three
Three -button
-button
-button
-button mode
mode
mode
mode external
external
external
external button
button
button
button switch
switch
switch
switch (not
(not
(not
(not supply):
supply):
supply):
supply): press ‘ OPEN ’ button, the gate opens.
Press ‘ STOP ’ button, the gate stops. Press ‘ CLOSE ’ button, the gate closes.
�Single
Single
Single
Single -button
-button
-button
-button mode
mode
mode
mode external
external
external
external button
button
button
button switch
switch
switch
switch /
/
/
/ keypad
keypad
keypad
keypad (not
(not
(not
(not supply):
supply):
supply):
supply): With each press of the button ,
the gate will close, stop, open or stop cycle.
�
�
�
�Auto-reverse
Auto-reverse
Auto-reverse
Auto-reverse function:
function:
function:
function: After adjusting the opening force and closing force, t he gate will reverse
and go open if obstructed when closing, and will stop if jammed when opening.
�
�
�
�Auto-close
Auto-close
Auto-close
Auto-close function:
function:
function:
function: This feature can be selected to make the gate stay open for some seconds
before it automatically closes. The auto-close time can be adjusted to between 0 and 44 seconds.
�
�
�
�Pedestrian
Pedestrian
Pedestrian
Pedestrian mode:
mode:
mode:
mode: This feature can be used to open gate about 0.3~1.5 meters for people pass
through.
�
�
�
�Safe
Safe
Safe
Safe guard
guard
guard
guard (Infrared
(Infrared
(Infrared
(Infrared photocell):
photocell):
photocell):
photocell): If infrared beam is interrupted during closing, the gate will reverse
and go open immediately. This feature will not function if the gate is in fully opened and closed
positions or during opening.
�Open
Open
Open
Open priority:
priority:
priority:
priority: T he gate will return to open if press ‘ OPEN ’ button of external button switch during
closing.
�
�
�
�Limit
Limit
Limit
Limit switch:
switch:
switch:
switch: T he switch is used to accurately stop the gate in the opened and closed positions.
If the gate stops at opened position when the limit switch is reached, the gate will not move if you
press ‘ OPEN ’ button.

PY500AC SLIDING GATE OPERATOR
14
If the gate stops at closed position when the limit switch is reached, the gate will not move if you
press ‘ CLOSE ’ button.
�
�
�
�The device is installed with a thermal protector, the thermal protector will switch off the motor
automatically in case of the temperature is higher than 120 ° C and switch on the motor automatically
when the temperature is lower than 85 ° C ±5 ° C.
9.
9.
9.
9. Maintenance
Maintenance
Maintenance
Maintenance
�
�
�
�Check the door once a month. The door should be carefully checked for balance. The door must be
in good working order .
�
�
�
� Th e auto-reverse function should be regularly inspected, and adjusted if necessary. For service, call
an experienced serviceman.
�
�
�
�We suggest for safety reasons, photocells be used on all gates.
�
�
�
�Disconnect from mains supply before replacing bulb.
�
�
�
�Be sure to read the entire manual before attempting to perform any installation or service to the door
operator.
�
�
�
�Our company reserves the right to change the design and specification without prior notification.
10.
10.
10.
10. Troubleshooting
Troubleshooting
Troubleshooting
Troubleshooting
11.
11.
11.
11. Packing
Packing
Packing
Packing list
list
list
list
After receiving the gate operator, you should make an unpack-inspection, in which you should check
whether the product was damaged. If you have any problem please contact our dealer. You should find
the following items in our standard packing:
Trouble
Possible cause s
Solutions
The door fails to open
and close. LED display
does not light.
1. Power is OFF
2. Fuse burn
1. Make sure that power is ON.
2. Replace fuse.
The door can open, fails
to close.
1. Infrared beam is obstructed.
2.Infrared photocell function is
enable, but the photocell has not
been installed.
1. Remove obstructions.
2.Make sure the infrared
photocell function is disable.
Remote transmitter does
not work.
1. Battery level may be low
2. Transmitter code is lost
1. Replace the battery inside
the transmitter.
2. Re -program the transmitter.
The transmitter operating
distance is too short.
Battery level may be low.
Replac e battery .
No.
Item
Quantity
1
PY500AC sliding gate operator
1
2
T ransmitter
2
3
Release key
1
4
User ’ s manual
1