ARC R11-W User manual

BAG 01BAG 01BAG 01
BAG 01
BAG 01
BAG 02
0201
2
1
2
1
2
3
3
1
2
3
1
2
3
1
R106021
10x15x4mm Ball Bearing (4)
R111160
R11 Eccentric Hub (4)
R105201
2.5x8mm Flat Screw (10)
R10102E
Rear Diff Case
R101110
Diff Gears (with Axle)
R103023
Gear Diff Shim Small (8)
R104005
O'ring 26x1 For Diff Case (2)
R101110
Diff Gears (with Axle)
R103110
Gear Diff Out Drive Spring Steel
R103024
Gear Diff Shim Big (4)
R104006
O’ring 5x2 (4)
R106101
Ø2x9.8 Pin (10)
NOTICE
Diff case direction needs to
match as below.
NOTICE
Trim any excess flashing
from the diff gear axle at
the mold injection point.
NOTICE
We recomment using 1.5 grams
of sillicone diff oil.
NOTICE
Front Diff Oil #60000
Rear Diff Oil #10000
NOTICE
Front Shock-Short
NOTICE
Rear Shock-Long
Front Shock (Short) x 2Set Rear Shock (Long) x 2Set
Apply Silicone Oil
Apply Silicone Oil
(4pcs)(1pcs)
(4pcs)
Fill oil to top of axle
as pictured here
R102004
Spur Axle Alu
R10102C
19T Belt Pulley Set (2)
R105103
3x4 Round Screw (10)
R105504
E-Clip 4mm (8)
R106104
Ø2x11.8mm Pin (10)
R104101
CNC Spur 84T(48dp)
R106010
5x8x2.5mm Ball Bearing (4)
R112030
R11 Shock Low Cap-Black (2)
R112032
R11 Shock Adj Nut-Black (2)
R104002
O’ring 3x2 (4)
R102029
Shock Body Alu Short (2)
R102067
Shock Body Long Big Bore (2)
R104015
Shock Shaft Shim (4)
R103013
Shock Shaft (2)
R103019
Shock Shaft Short (2)
R104017
Shock Piston Big Bore 1.1mm x3 (4)
R104013
O’ring 13x1 (2)
R105501
E-Clip 2mm (10)
Apply shock oil
before assembly
R101130
Shock Ball Joint Set Big Bore
(4pcs) (4pcs)(2pcs) (2pcs)

BAG 02
BAG 02
03 04
BAG 02
BAG 02
2
1
#0 #0
#1 #1
#2
Flat side out
Cut side out
Cut side in
Flat side in
#2
#-1 #-1
Option Parts Default use in Front & REAR
0 0
R103027
5.8mm Ball End Short (4)
R101130
Shock Ball Joint Set Big Bore
(4pcs)
(4pcs)
(2pcs)
(2pcs)
R107042
Front Shock Spring short (Yellow)(2)
R107031
Rear Shock Spring Long (Green)(2)
R112031
R11 Shock Cap-Black (2)
R104016
Shock Membrance Big Bore (4)
Silicone Oil #500
Rear (Long)
Set to 59mm
Front (Short)
Set to 57.5mm
25%
50%
75%
PUSH
Short Long
Drill the shock cap here to help provide zero
rebound and softer dampening (optional setting)
Move the shaft up and down to
let the air escape from the oil
Fill the shock oil to the top of the
shock body
To adjust the rebound amount of the shock,
push the shock shaft in to the required level
to remove excess oil during assembly
Build shocks to the
following lengths
R112001
R11 Bulkhead
R105203
3x6mm Flat Screw (10)
R105203
3x6mm Flat Screw (10)
R119001
R11 Separated Suspension Block #2
R119002
R11 Separated Suspension Block #0
0
0
0
0
R112060
R11W Main Chassis-Alu
R119002
R11 Separated Suspension Block #0

BAG 03
BAG 03
05 06
BAG 03
BAG 03
Rear Suspension Block Chart with Suspension Block #3
Front Suspension Block Chart with Suspension Block #1
NOTICENOTICE
TH
TH
R112004
R11 Motor Bulkhead-Mono
R112006
R11 Motor Bulkhead Mount Plate
R105205
3x10mm Flat Screw (10)
R105203
3x6mm Flat Screw (10)
R105104
3x6 Round Screw (10)
2
2 2 2 2
Front lower arm 1 degree in-board toe in Front lower arm 2 degree in-board toe out
Front lower arm 1 degree in-board toe out Front lower arm zero in-board toe
1.0 degree rear toe-in 4.0 degree rear toe-in
3.0 degree rear toe-in 2.0 degree rear toe-in
2
0
0 0 0 0
0 0 0
2 2
R115001
3mm Nylon Nut-Black Alu (4)
R105203
R105203
R105205
R112007
R11 Center Tower-Alu
Option parts R112002
R11 Upper Bulkhead (FR/RL)
R112003
R11 Upper Bulkhead (FL/RR)
R118020
R11 Shock Tower-Front (Short)
R118023
R11 Rear (Long) Shock Tower
R105104
3x6 Round Screw (10)
R105204
3x8mm Flat Screw (10)
NOTICE
Apply thread locking compund here.
R114001
R11 Front Belt Rubber 3mm
R112005
Spur Ball Bearing Holder (2)
R104051
R10 Rear Belt Rubber 3mm Initial Position
Tighten
Initial Position
LoosenTighten
FRONT END REAR END
Loosen
R805010
3x5mm Flat Screw (10)

07 08
BAG 04
BAG 04
BAG 04
BAG 04
BAG 04
TH
TH
NOTICE
Apply thread locking compund here.
R118013
R11 Floating Servo Mount
R112008
R11 Servo Mount Base
R112009
R11 Servo Mount-Left
R105104
3x6 Round Screw (10)
R105105
3x8 Round Screw (10)
NOTICE
It is recommended to use servo
mount rubber.
Not included
R105205
3x10mm Flat Screw (10)
R105205
R103012
R103012
R103011
R103011
R103011
R103017
R105203
R105104
R105105
R105203
3x6mm Flat Screw (10)
R10107A
Ball Joint 4.9mm open (6)
R10107D
Steering Rod Ball Joint
R103011
4.9mm Ball End Short (4)
R103017
4.9mm Ball End Med (4)
R103012
4.9mm Ball End Long (4)
R102817
Turnbuckle 3x43mm ALU-7075
R103011
4.9mm Ball End Short (4)
R103030
Turnbuckle 3x20mm (2)
29.1mm
10mm
R111160
R11 Eccentric Hub (4)
(4pcs)(1pcs)
R105203
3x6mm Flat Screw (10)
R112040
Steering Plate 8.5
R103041
Floating Servo Mount Tower (2)
R101060
Servo Horn dual steering arm
R105104
3x6mm Round Screw (10)
R102017
3x5.5x3mm Alu Shims (4) R106010
5x8x2.5mm Ball Bearing (4)
R105203
3x6mm Flat Screw (10)
It is recommended to place the
notch on each turnbuckle to
the right side, which will make
it easier to adjust camber and
toe in the future.
NOTICE

BAG 04
BAG 04
09 10
BAG 04
BAG 05
2
3
4
1
GE
GE
R112063
R11W Suspension Block #1
R105203
3x6mm Flat Screw (10)
R10107A
Ball Joint 4.9mm open (6)
R10107C
Anti-Roll Bar Joint (4)
R103017
4.9mm Ball End Med (4)
R105403
3x8mm Set Screw (10)
R105404
3x10mm Set Screw (10)
R105203
3x6mm Flat Screw (10)
R105403
3x8mm Set Screw (10)
R105404
3x10mm Set Screw (10)
R103040
Pivot Pin Inner (2)
R103008
Ball 5mm (4)
R10110F
Low Arm F Set with Shims
R10110A
Front lower arms have 4 different shock positions.
Make sure left and right sides are both symmetrical
during assembly.
32mm 27.6mm
33mm 28.6mm 28.6mm 33mm
27.6mm 39.5mm
Initial Setup
32mm
Initial Setup
Rear lower arms have 6 different positions for shocks and anti-roll bars.
Make sure left and right sides are symmetrical during assembly.
When assembling the front and rear arms, please pay
attention to these notches for correct orientation.
39.5mm 30.7mm
35.1mm
30.7mm
35.1mm
40.5mm 31.7mm
36.1mm
31.7mm 40.5mm
36.1mm
R105403
R105404
R105404
Plastic Shims
(1mm)
Plastic Shims
(1mm)
Use Default Setup 27.6mm Offset Hole
R105403
29.1mm 29.1mm
R10107A
Ball Joint 4.9mm open (6)
R103011
4.9mm Ball End Short (4)
R112062
R11W Suspension Block #3
R103040
Pivot Pin Inner-Short (2)
R103008
Ball 5mm (4)
R10110A
R10110R
Low Arm R Set with Shims
R105403
R105404
R105404
R103017
R103011
(Middle Hole)
(Middle Hole)
R105403
R107001
CDV G-Clip (8)
R106101
Ø2x9.8mm Pin (10)
R106102
Ø2x10mm Pin (10)
R103002
Wheel Axle (2)
R103111
R10W Spring Steel Drive Shaft (2)
R103005
CVD Insert (2)
R102005
Hex Wheel Hub Alu (2)
R101090
Steering Block and Upright
R106102
Plastic Shims
(1mm)
Plastic Shims
(1mm)
R106012
5x10x4mm Ball Bearing (4)
Use Default Setup 35.1mm Offset Hole
R106101
R106101
R105101
2x5mm Cap Screw (10)
Apply Grease
R103017
4.9mm Ball End Med (4)

BAG 05
BAG 05
11 12
BAG 06
BAG 06
BAG 06
R10107A
Ball Joint 4.9mm open (6)
R105105
3x8mm Round Screw (10)
Right side
Left side
R
L
R103007
Steering Block Bushing (4)
R101080
C-Hub 4 Right + Left
R103017
4.9mm Ball End Med (4)
R103017 R103012Length 19.3mm X 2 Set
Front Link
Rear Link
R103017 R103012
R102014
(1mm)
R102017
(3mm)
R102017
(3mm)
R102017
(3mm)
R102018
(4mm)
R103016
R103015
Length 17.6mm X 2 Set
R103012
4.9mm Ball End Long (4)
R102017
3x5.5x3mm Alu Shims (4)
R102018
3x5.5x4mm Alu Shims (4)
R102014
3x5.5x1mm Alu Shims (4)
R105402
3x4mm Set Screw (10)
R103015
Pivot Pin Front-Out (23mm)(2)
R103016
Pivot Pin Rear-Out (25mm)(2)
R10107B
Ball Joint 4.9mm closed (4)
R102813
Turnbuckle 3x28mm ALU-7075 (2)
R113001
Anti-Roll Bar Holder (2)
R113001
Anti-Roll Bar Holder (2)
R118002
R11 Upper Deck 2.0mm
R119003
R11 Belt Tensioner
R107014
Rear Anti-Roll Bar 1.3mm
R107012
Front Anti-Roll Bar 1.4mm
R105401
3x3mm Set Screw (10)
R105104
3x6mm Round Screw (10)
R806001
3x6x2.5mm
Flange Ball Bearing (2)
R105401
3x3mm Set Screw (10)
R806001
3x6x2.5mm
Flange Ball Bearing (2)

BAG 06
BAG 06
13 14
BAG 06
BAG 06
R105150
3mm Nylon Nut (10)
R105105
3x8mm Round Screw (10)
R105205
3x10mm Flat Screw (10)
R101050
Bumper /Tower Set
(x2)
(x2)
R104010
Foam Bumper
NOTICE
The lower bumper can be cut as marked to
make it smaller and les likely to touch the
racing surface during cornering, however
it will provide less protection.
(x4)
R102015
3x5.5x2mm Alu Shims
R102015
3x5.5x2mm Alu Shims (8)
(2mm)
R101050
Bumper /Tower Set
R106104
Ø2x11.8mm Pin (10)
R106104
Ø2x11.8mm Pin (10)
R107002
R-Clip
R105105
3x8mm Round Screw (10)
R105105
3x8mm Round Screw (10)
R101050
Bumper /Tower Set
(2pcs)
(2pcs)
(2pcs)
R105106
3x10 Round Screw (10)

BAG 06
BAG 06
15 16
BAG 06
BAG 06
SIDE WAY BATTERY TAPE
R118010
Battery Holder-Front
R118011
Battery Holder-Rear
R10110C
3x6x3mm Plastic Shims
R105204
R105206
Motor Pinion (48p)
(Not included)
Brushless Motor
(Not included)
R105401
3x3mm Set Screw (10)
R105204
3x8mm Flat Screw (10)
R105206
3x12mm Flat Screw (10)
R115001
3mm Nylon Nut-Black Alu (4)
R105300
3x6mm Cap Screw (10)
R105401
3x3mm Set Screw (10)
R104150
Antenna
Lipo battery and battery tape
not included
Chamfer the edges of the
battery tape slots
Double sided tape (Not included)
ESC. Receiver (Not included)
SIDE WAY BATTERY TAPE
The sideways mounting method can
help increase chassis flex.

BAG 06
BAG 06
17 18
Lipo battery and battery tape
not included
1/10 Foam Tires Front 26mm (Not Included)
1/10 Foam Tires Rear 30mm (Not Included)
Chamfer the edges of the
battery tape slots
TRADITIONAL BATTERY MOUNTING METHOD
R105151
4mm Serrated Wheel Nut (4)
Use glass fiber tape attached to the battery
mount plate to secure the battery.
Spur
Pinion
18 6.22 6.44 6.67 6.89 7.11 7.33 7.56 7.78 8.00 8.22 8.44 8.67 8.89 9.00 9.11 9.22 9.33 9.44
19 5.89 6.11 6.32 6.53 6.74 6.95 7.16 7.37 7.58 7.79 8.00 8.21 8.42 8.53 8.63 8.74 8.84 8.95
20 5.60 5.80 6.00 6.20 6.40 6.60 6.80 7.00 7.20 7.40 7.60 7.80 8.00 8.10 8.20 8.30 8.40 8.50
21 5.33 5.52 5.71 5.90 6.10 6.29 6.48 6.67 6.86 7.05 7.24 7.43 7.62 7.71 7.81 7.90 8.00 8.10
22 5.09 5.27 5.45 5.64 5.82 6.00 6.18 6.36 6.55 6.73 6.91 7.09 7.27 7.36 7.45 7.55 7.64 7.73
23 4.87 5.04 5.22 5.39 5.57 5.74 5.91 6.09 6.26 6.43 6.61 6.78 6.96 7.04 7.13 7.22 7.30 7.39
24 4.67 4.83 5.00 5.17 5.33 5.50 5.67 5.83 6.00 6.17 6.33 6.50 6.67 6.75 6.83 6.92 7.00 7.08
25 4.48 4.64 4.80 4.96 5.12 5.28 5.44 5.60 5.76 5.92 6.08 6.24 6.40 6.48 6.56 6.64 6.72 6.80
26 4.31 4.46 4.62 4.77 4.92 5.08 5.23 5.38 5.54 5.69 5.85 6.00 6.15 6.23 6.31 6.38 6.46 6.54
27 4.15 4.30 4.44 4.59 4.74 4.89 5.04 5.19 5.33 5.48 5.63 5.78 5.93 6.00 6.07 6.15 6.22 6.30
28 4.00 4.14 4.29 4.43 4.57 4.71 4.86 5.00 5.14 5.29 5.43 5.57 5.71 5.79 5.86 5.93 6.00 6.07
29 3.86 4.00 4.14 4.28 4.41 4.55 4.69 4.83 4.97 5.10 5.24 5.38 5.52 5.59 5.66 5.72 5.79 5.86
30 3.73 3.87 4.00 4.13 4.27 4.40 4.53 4.67 4.80 4.93 5.07 5.20 5.33 5.40 5.47 5.53 5.60 5.67
31 3.61 3.74 3.87 4.00 4.13 4.26 4.39 4.52 4.65 4.77 4.90 5.03 5.16 5.23 5.29 5.35 5.42 5.48
32 3.50 3.63 3.75 3.88 4.00 4.13 4.25 4.38 4.50 4.63 4.75 4.88 5.00 5.06 5.13 5.19 5.25 5.31
33 3.39 3.52 3.64 3.76 3.88 4.00 4.12 4.24 4.36 4.48 4.61 4.73 4.85 4.91 4.97 5.03 5.09 5.15
34 3.29 3.41 3.53 3.65 3.76 3.88 4.00 4.12 4.24 4.35 4.47 4.59 4.71 4.76 4.82 4.88 4.94 5.00
35 3.20 3.31 3.43 3.54 3.66 3.77 3.89 4.00 4.11 4.23 4.34 4.46 4.57 4.63 4.69 4.74 4.80 4.86
36 3.11 3.22 3.33 3.44 3.56 3.67 3.78 3.89 4.00 4.11 4.22 4.33 4.44 4.50 4.56 4.61 4.67 4.72
37 3.03 3.14 3.24 3.35 3.46 3.57 3.68 3.78 3.89 4.00 4.11 4.22 4.32 4.38 4.43 4.49 4.54 4.59
38 2.95 3.05 3.16 3.26 3.37 3.47 3.58 3.68 3.79 3.89 4.00 4.11 4.21 4.26 4.32 4.37 4.42 4.47
39 2.87 2.97 3.08 3.18 3.28 3.38 3.49 3.59 3.69 3.79 3.90 4.00 4.10 4.15 4.21 4.26 4.31 4.36
40 2.80 2.90 3.00 3.10 3.20 3.30 3.40 3.50 3.60 3.70 3.80 3.90 4.00 4.05 4.10 4.15 4.20 4.25
76 78 80 8256 58 60 62 83 84 8564 66 68 70 72 8174
ARC R11 GEAR RATIO CHART 48DP
ARC R11 Internal Gear Ratio = 2.0
19T 38T38T