ARCADE SHOCK QANBA OBSIDIAN User manual

QANBA OBSIDIAN
“HIT BOX” CONVERSION KIT INSTALL GUIDE
QANBA OBSIDIAN (SOLD SEPARATELY)
OBSIDIAN HIT BOX METAL PANEL*x1
OBSIDIAN HIT BOX TOP PLEXI TOP*x1
5-PIN to HITBOX
CONVERSION CABLE x1
*REMOVE PROTECTIVE BLUE FILM BEFORE INSTALLTION
ITEM CHECKLIST
METALLIC
SCREW COVERS
(OPTIONAL)
ARCADESHOCK.COM

SUGGESTED TOOLS
SLOTTED (FLATHEAD) SCREWDRIVER
PHILIPS SCREWDRIVER (PH2)
ROTARY CUTTING TOOL
SMALL POKING TOOL
1
INSTALL PROCESS
UNDO THE SIX (6) BOTTOM SCREWS TO OPEN THE ARCADE STICK BODY
UTILITY KNIFE/CUTTER
ARCADESHOCK.COM

2
ONCE OPEN UNDO ALL WIRING AND
UNINSTALL ALL EIGHT BUTTONS
AND THE JOYSTICK
3
USING A SMALL POKING TOOL CAREFULLY
REMOVE THE METALLIC SCREW COVERS.
ONCE REMOVED, CONTINUE TO UNSCREW
USING A PHILIPS SCREWDRIVER THE PLEXI
TOP OF THE ARCADE STICK.
CAREFULLY UNPLUG AND SET ASIDE THE
5-PIN JOYSTICK HARNESS FROM THE PCB
ARCADESHOCK.COM

4
ONCE THE BARE METAL PANEL
IS EXPOSED CONTINUE TO DISASSEMBLE
BY UNDOING THE SIX (6) SCREWS ON THE
PANEL USING A PHILIPS SCREWDRIVER
5
TAKE NOTE OF THE MIDDLE BOTTOM
AREA.
ALIGN THE OBSIDIAN HIT BOX
METAL PANEL IN PLACE.
ARCADESHOCK.COM

7
ON THE 30MM BUTTON HOLE, USE THE PANEL AS A GUIDE
AND MARK THE EXTENDED PLASTIC AREA WITH A SHARP TOOL
OR MARKER
8
USING A CUTTING TOOL SUCH AS A ROTARY TOOL, TRIM PLASTIC
DOWN TO THE PREVIOUSLY MARKED PORTION.
THIS WILL ALLOW FOR THE 30MM BUTTON (UP DIRECTION) TO FIT
THROUGH THE PANEL.
ARCADESHOCK.COM

9
CONTINUE TO SECURE THE HITBOX METAL PANEL WITH
THE PREVIOUSLY REMOVED SIX (6) SCREWS
SIMILARLY SECURE THE HITBOX TOP PLEXI ON
THEIR RESPECTIVE SIX SCREW POINTS.
ARCADESHOCK.COM

10
RETRIEVE THE
JOYSTICK HARNESS
ON THE 5-PIN HEADER WHERE THE JOYSTICK CONNECTS,
USE A POKING TOOL PRESS CAREFULLY ON THE CONNECTORS.
THERE IS A TINY KNOTCH THAT WHEN PRESSED DOWN,
WILL RELEASE THE WIRES FROM THE HEADER WHEN PULLED.
RE-ORDER THE WIRES
EXCEPT FOR BLACK.
BLACK
YELLOW
GREEN
RED
ORANGE
ARCADESHOCK.COM
ON THE JOYSTICK CONNECTOR SIDE,
THE 5-PIN HEADER SHOULD
BE IN THIS SEQUENCE:

11
RED YELLOW BLUE
GREEN
BLACK ORANGE PURPLE
BROWN
INSTALL THE PUSHBUTTONS
AND RE-CONNECT THE WIRES
FOR THE ACTION BUTTONS
USE THIS COLOR GUIDE TO WIRE IT IN THE CORRECT ORDER
(VIEW FROM BOTTOM/INSIDE THE ARCADE STICK AS SHOWN)
12
PLUG THE JOYSTICK HARNES
BACK INTO THE MAIN PCB.
PROCEED THEN TO CONNECT
THE 5-PIN HITBOX
CONVERSION CABLE.
WIRE IT ACCORDINGLY USING
THE COLOR GUIDE BELOW.
ORANGE
GREEN
RED YELLOW
ARCADESHOCK.COM

13
AFTER WIRING IS DONE, REASSEMBLE THE
BOTTOM LIDTO CLOSE-UP THE ENCLOSURE
14
ONCE ASSEMBLY IS COMPLETE, THE OBSIDIAN HIT BOX
SHOULD BE FULLY FUNCTIONAL AND READY FOR USE.
ARCADESHOCK.COM

METALLIC SCREW COVERS (OPTIONAL)
THE METALLIC SCREW COVERS ARE NOT NECESSARY
FOR A STABLE CONSTRUCTION. ALTHOUGH, ADDING IT
WILL PREVENT RUST ON THE SCREWS AS WELL AS A
MORE REFINED AESTHETIC LOOK TO YOUR ASSEMBLY.
METALLIC SCREW COVERS - TOOLS NEEDED
HEATED GLUE GUN
(WITH REST IS PREFERRED)
MICROFIBER
CLEANING CLOTH
ISOPROPHYL ALCOHOL
(RUBBING ALCOHOL)
* SET OF 8 SOLD SEPARATELY
ARCADESHOCK.COM

METALLIC SCREW COVERS - APPLICATION
MAKE SURE THE SCREW IS
SECURELY INSTALLED.
TAKE NOTE OF HOW RECESSED
IT IS AFTER IT IS SECURED.
IN THIS AREA, CAREFULLY
DAB SOME HOT GLUE USING
A HEATED GLUE GUN.
A SMALL PORTION WILL BE
ENOUGH, AND MAKE SURE
NOT TO PUT TOO MUCH.
QUICKLY APPLY THE
METALLIC SCREW COVER
OVER THE MELTED GLUE.
IF EXCESS GLUE SEEPS OUT,
WAIT FOR IT TO COOL DOWN.
DAMPEN YOUR CLEANING
CLOTH WITH SOME
RUBBING ALCOHOL.
AND PROCEED TO CLEAN
OFF THE DRIED EXCESS
GLUE WITH THE CLOTH.
ARCADESHOCK.COM

METALLIC SCREW COVERS - APPLICATION
FOR A SUCCESSFUL APPLICATION
IT SHOULD BE FLUSHED AND
SMOOTH
ALONGSIDE THE PANEL AS IF IT
WERE STOCK.
ARCADESHOCK.COM
END