Innovative Concepts in Entertainment MONOPOLY ROLL-N-GO User manual

1
Service Manual
Innovative Concepts in Entertainment
10123 Main Street
Clarence, New York 14031
[phone] 8:30am to 6:00pm EST
WWW.ICEGAME.COM

2
Table of Contents
Safety and Warnings 3
Game Play 4
Parts Included 5
Back Cabinet Hole Plug Install 6
Game Assembly 7 - 10
Bonus Chart recommendations 11 - 12
Card Swipe Install 13
Programming 14 - 19
Access to Game Electronics 20
Access to Safety Sensors
Monitor Replacement Instructions 21 - 23
Assembly Drawings 24
RM1050X Encoder Assembly 25 - 27
RM3044X Left Podium 27 - 31
RM3004X Monitor bracket 32
RM3020X Marquee Assembly 33
RM3030X & RM3031X - City scape sides 34
RM3036X & RM3037X Pointers 35
RM3074X Electronics tray 36 - 37
UCL Harness Connection Information 38
Electronic Parts 39
LED Breakdown 40
Graphic Decal listing 41
Warranty 42
REV B - 6/5/2020

3
SAFETY AND WARNINGS BEFORE YOU BEGIN
WARNING: WHEN INSTALLING THIS GAME, A GROUNDED A.C. RECEPTACLE MUST BE USED.
FAILURE TO DO SO COULD RESULT IN INJURY TO YOURSELF OR OTHERS. FAILURE TO USE A
GROUNDED RECEPTACLE COULD ALSO CAUSE IMPROPER GAME OPERATION, OR DAMAGE TO
THE ELECTRONICS.
NOTE: THIS GAME IS INTENDED FOR INDOOR USE ONLY.
DO NOT DEFEAT OR REMOVE THE GROUNDING PRONG ON THE POWER CORD FOR THE SAME
REASON AS GIVEN ABOVE. USING AN IMPROPERLY GROUNDED GAME COULD VOID YOUR
WARRANTY.
HAVE A QUALIFIED ELECTRICIAN CHECK YOUR A.C. RECEPTACLE TO BE SURE THE GROUND
IS FUNCTIONING PROPERLY.
THIS GAME IS DESIGNED TO DISSIPATE STATIC ELECTRICITY THROUGH THE GROUNDING
PLANE OF THE GAME. IF THE A.C. GROUND DOES NOT WORK, THE GAME COULD DISCHARGE
STATIC ELECTRICITY THROUGH THE GAME CIRCUITRY, WHICH COULD CAUSE DAMAGE.
THE POWER SUPPLY IS NOT VOLTAGE ADJUSTABLE. TO OPERATE THE GAME AT VOLTAGES
OTHER THAN THOSE IT WAS DESIGNED FOR. PLEASE CONTACT OUR SERVICE DEPARTMENT
FOR VOLTAGE CONVERSION INFORMATION.
WARNING
DO NOT remove any of the components on the main board (e.g. compact flash and eproms)
while the game is powered on. This may cause permanent damage to the parts and the main
board. Removing any main board component part while powered on will void the warranty.
ALWAYS REMOVE POWER TO THE GAME, BEFORE ATTEMPTING ANY SERVICE,
UNLESS NEEDED FOR SPECIFIC TESTING. FAILURE TO OBSERVE THIS PRECAUTION
COULD RESULT IN SERIOUS INJURY TO YOURSELF OR OTHERS.
THIS GAME IS NOT SUITABLE FOR INSTALLATION IN AN AREA WHERE A WATER JET COULD BE
USED.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their safety. Children should be
supervised to ensure that they do not play with the appliance.
AC Power Information
The games main fuse is accessed through the back of the game at the power mod. Above the
power cord is a small panel that contains the main fuse.
The value of the fuse for 120 volt users is 7 AMPS at 250Volt type slow blow.
The value of the fuse for 230 volt users is 4 AMPS at 250 Volt type slow blow.

4
Game Play
The object of the game is to WIN BIG! Players skillfully spin the LED-lit dice to land on spaces. The
players goal is to hit the many bonus spaces and win lots of tickets!
To win the “Monopoly Bonus” a player needs to land on two of the same color properties. They will
win 10X the value of that property if they do so! There are eight different colored families to win.
Each family has two properties in each. The time to be able to win the “Monopoly Bonus” can be
adjusted by the operator from 60 seconds to 600 seconds.
The “Go Bonus” space progressively increases (This bonus doesn’t always increment every play).
This will continue to increase until a player lands on the “Go Bonus” space winning the bonus. It will
then reset and start again. The “Free Parking Bonus” is the most exciting bonus to win. If a payer
lands on the free parking space once, it will double all the values of the properties on the board (with
the exception of the Monopoly Bonus property and Go Bonus spaces). If a player lands on the Free
Parking Bonus space again on the next spin, all properties (except Monopoly Bonus and Go Bonus
spaces) would be worth ten times their values!
Players can double the amount tickets they can win by playing with two credits at the same time
using the double down button!
Possible Chance cards the player can win:
● ADVANCE TO GO. ● ADVANCE TO PARK PLACE.
● MOVE FORWARD ONE SPACE. ● MOVE FORWARD FIVE SPACES.
● MOVE FORWARD ELEVEN SPACES. ● GO BACK ONE SPACE.
● GO BACK FIVE SPACES. ● GO BACK ELEVEN SPACES.
● YOUR BANK PAYS YOU INTEREST. COLLECT XXX TICKETS.
● YOUR BUILDING LOAN MATURES. COLLECT XXX TICKETS.
● SPEEDING FINE REFUND. COLLECT XXX TICKETS.
● RECEIVE FOR CONSULTANCY FEES. COLLECT XXX TICKETS.
● YOU ARE ELECTED CHAIRMAN OF THE BOARD. COLLECT XXX TICKETS.
● YOU RECEIVE AN INHERITANCE. COLLECT XXX TICKETS.

5
RM3011
RM3010
E00789RMX
X’s 2
X’s 2
RM3079
RM3031x (right)
RM3030X (left)
In TV bag: Remote control and IR extender
If any you are missing any of the parts below please contact ICE service department.
Monday through Friday 8:30am to 6pm Eastern standard time at [phone].
You can also visit our webpage at WWW.ICEGAME.COM
Parts included with your game.

6
AA3052 Hole Plug
AB
CD
A
BD
A
B
C
Back Cabinet Hole Plug Installation
After removing the shipping bolts used to secure the back cabinet to the shipping pallet, insert four
hole plugs into the holes the bolts were removed from. See below for location. The hole plugs are
in the hardware kit.

7
Step 3:
Secure the wire covers using twelve AA6383 8-32 x 1 1/2.
Do not pinch the harnesses when securing.
Step 2:
Plug harnesses together and place wire cover on top.
Cabinet ASSEMBLY
Step 1:
Before sliding the cabinets together, pull the main harness up and
center it in the groove to ensure it does not get pinched between
cabinets. Make sure to clear any large debris out of the triangular
floor pockets. Then lift the podium edge onto the main cabinet floor,
the wedge shapes guide the cabinet into position and stop it when
the mounting holes are lined up. Secure with four AA6281s 1/4-20
x 1-1/2" and four AA6212 1/4" washers
Screw holes will be covered by harness!

8
Step 4:
Lift the hinged monitor up and lock into
place using one AA6281 (1/4-20 x 1-
1/2") Allen bolt on each side shown
below.
DO NOT LIFT BY THE MONITOR OR
MARQUEE!
USE A FRIEND TO LIFT!
KEEP HANDS AND FINGERS AWAY
FROM MONTY’S HAT AS YOU LIFT
THE MONITOR UP!
Step 5:
Locate the two cityscapes panels. Insert three AA6510 (1/4-20 x 1 37/64) Allen head bolts into the
holes shown below in both cityscape panels. Do not fully tighten, only install them two turns (See
next step)

9
Step 7:
Connect the Cityscape harnesses. Only the right side cityscape will use both connections.
The right side is not used.
Step 6: A large oval hole on the sides of the cabinet is where the wire harness should be inserted
through. Then insert the bolts you installed into the holes and then slide the cityscape down to lock
them in. Secure by tightening the bolts with a 5/32 bit included in the parts kit from the inside of the
cabinet. Repeat for the other side.
Insert
harness

10
Step 8:
Attach the white trim to the inside of each side of the cabinet.
Secure using AA6383 (8-32 x 1-1/2") bolts and AA6240 (#8)
washers. 4 per each side.
Step 9:
Remove the six security screws holding the plaque in place on the right-side. Attach the correct
bonus decal and re-secure the plaque back to the cabinet. See next page to determine correct
bonus decal.