Arcam AVR200 User manual

AVR200
DiVA AVR200
Surround Sound Receiver
Service Manual
ARCAM
ARCAM
Issue 1.0

SERVICE MANUAL
AA
AAVV VVRR RR22 2200 0000 00
SURROUND SOUND RECEIVER
CONTENTS Page
SPECIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-3
DISASSEMBLY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
BLOCK DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
ADJUSTMENT POINTS DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
INSTRUMENT SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
ALIGNMENT PROCEDURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-9
IMPORTANT NOTES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
PCB LAYOUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-20
SCHEMATIC DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21-40
IC BLOCK DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41-49
ELECTRICAL PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40-67

SURROUND SOUND RECEIVER AA
AAVV VVRR RR22 2200 0000 00
- 2 -
POWER AMPLIFIER AND PREAMPLIFIER SECTION
Rated distortion (THD 20Hz-20 kHz FL/C/FR) ≤0.08%
(THD 20Hz-20 kHz SL/SR) ≤0.3%
Input Sensitivity (ref. 8 ohms, 1 kHz) 180+/-30 mV
S/N Ratio (A-wtd, 1KHz, 1W, 8 ohm) ≥-75 dB
(A-wtd, 1KHz, 80W, 8 ohm) FL/FR/C ≥92 dB
SL/SR ≥-90 dB
Frequency Response (20 Hz - 20 kHz) 0 ± 0.8 dB
Channel Balance (1 dB to -40 dB, 1 kHz) ≤2 dB
(-41 dB to -50 dB, 1 kHz) ≤3 dB
Audio muting at 1kHz ≥53 dB
Headphone O/P in 0.1%, 600 ohm load, CD in 500mV, 1 kHz ≥10V
Subwoofer out, 500mV in (THD at 2V O/P, 100 Hz) ≥0.5%
(S/N at 2V O/P, 100 Hz) ≥80 dB
Crosstalk (2V input, 10W, 1 kHz) > -68 dB
Continuous average power output (L/R/C RL/RR 8ohms) 80 W
Controls
Bass (at 500mV in, 1W out, 100 Hz) ±9dB
Treble (at 500mV in, 1W out, 10 kHz) ±9dB
SURROUND SECTION
Channel separation
I/p mode : L, R : 1V in, 1 kHz, Ch R, L ≥45 dB
: o/p at unexpected, 1 kHz, Ch C ≥35 dB
I/p mode : L= -R : 1V in, 1 kHz, Ch R, L ≥28 dB
: o/p at unexpected, 1 kHz, Ch C ≥30 dB
I/p mode : L= R : 1V in, 1 kHz, Ch R, L ≥45 dB
: o/p at unexpected, 1 kHz, Ch SL, SR ≥30 dB
Frequency Response
I/p mode : L, R : 1V in, 1W, Ch R, L 40Hz 0 ± 1.5 dB
20kHz 0 ± 0.8 dB
I/p mode : L= R : 1V in, 1W, Ch C 300Hz 0 ± 0.8 dB
20kHz 0 ± 0.8 dB
I/p mode : L= -R : 1V in, 1W, Ch SL, SR 30Hz 0 ± 1.0 dB
6.5kHz -3 ± 1.0 dB
S/N Ratio ( 200mV in, 1, A-WTD w/ 1k termination)
I/p mode : L, R : 1 kHz, Ch L, R ≥65 dB
I/p mode : L=R : 1 kHz, Ch C ≥65 dB
I/p mode : L=-R : 1 kHz, Ch SL, SR ≥65 dB
THD (2.2V in, 1W, w/ 80 kHz LPF, 1 kHz) ≤0.2%
AC-3/DTS SECTION
Frequency Response
FL, FR, C, SL, SR: 200Hz 0 ± 0.8 dB
20kHz 0 ± 0.8 dB
Distortion 1W all channels 0.08%
S/N 1 W ( CCIR/ARM, 200 Hz NOTCH & 400 Hz HPF) ≥85 dB
PROLOGIC II AUDIO
Center Width Control (Use track 2 from PLII Audio Test CD ver1.0)
SPECIFICATION
Step L/R C
0≤-31dB 0.0dB
1-12dB -0.6dB
2-9.6dB -1.1dB
3-7.6dB -1.8dB
4-4.8dB -4.6dB
Step L/R C
5-4.1dB -6.6dB
6-3.6dB -9.0dB
7-3.0dB ≤-31dB

SURROUND SOUND RECEIVER AA
AAVV VVRR RR22 2200 0000 00
- 3 -
Dimension Control (Use track 1 and 3 from PLII Audio Test CD ver1.0)
AM TUNER SECTION
Input level is expressed as the reading in open-circuit
of 75-ohm source impedance signal generator
Usable sensitivity (999/1000kHz) ≤30 dBµ
S/N Ratio (5mV in) ≥38 dB
THD (5mV in) ≤3%
IF Rejection (450 kHz) ≥36 dB
Image Rejection (F+2xIF) ≥28 dB
Selectivity ≥17 dB
Output 130+/- 20mV
Loop sensitivity (20dB S/N) 999/1000 kHz ≤66 dB
603/600 kHz ≤66 dB
1404/1400 kHz ≤66 dB
Frequency response (100 - 2.3 kHz, 5mV) ± 6 dB
FM TUNER SECTION *C *AH
Input level is expressed as the reading in open-circuit
of 75-ohm source impedance signal generator
Usable Sensitivity ( 98 MHz) ≤15 dBµ ≤15 dBµ
Signal / Noise Ratio Mono ≥72 dB ≥72 dB
(60 dBµ, IHF wtd) Stereo ≥66 dB ≥66 dB
Frequency Response (20 Hz - 15 kHz, 60 dBµ) 0 ± 1.5 dB 0 ± 1.5 dB
Channel Separation (60 dBµ) 100 Hz ≥30 dB ≥30dB
1 kHz ≥38 dB ≥38 dB
10 kHz ≥30 dB ≥30 dB
Alternate Channel Selectivity
(40 dBµ, ±400 kHz) ≥60 dB ≥45 dB
Capture Ratio (40 dBµ) ≤3 dB ≤3 dB
AM Suppression
(60 dBµ, 100% Mod.FM, 30% Mod.AM) ≥48 dB ≥48 dB
Image Rejection (119.4 MHz) ≥85 db ≥40 dB
I.F. Rejection ( 10.7 MHz) ≥78 dB ≥65 dB
Pilot Suppression (60 dBµ) ≥60 dB ≥60 dB
THD (60 dBµ, L=R 75 kHz for AH, 40 kHz Dev for C)
Mono ≤0.25% ≤0.25%
Stereo ≤0.35% ≤0.35%
Auto-Search Sensitivity On ≥24 dBµ ≥24 dBµ
Off ≤15 dBµ ≤15 dBµ
RDS decode Sensitivity ≤26 dBµ ≤26 dBµ
PHYSICAL SPECIFICATIONS
Dimensions (Width x Height x Depth) 422 x 132 x 290mm
Net weight 14kg (31 lbs)
Shipping weight 16.7kg (37 lbs)
Step C SL SR
-3 ≤-31dB -7.8dB ≤-31dB
-2 ≤-31dB -11.5dB ≤-31dB
-1 ≤-31dB -19.5dB ≤-31dB
0≤-30dB ≤-31dB ≤-31dB
Step C SL SR
1-20.4dB ≤-31dB ≤-31dB
2-14.0dB ≤-31dB ≤-31dB
3-11.5dB ≤-31dB ≤-31dB

SURROUND SOUND RECEIVER AA
AAVV VVRR RR22 2200 0000 00
- 4 -
DISASSEMBLY INSTRUCTIONS
1. Remove machine screws M 4.0 x 6.0 ( 1 to 6 ) from the side panels.
Remove tapping screw 3.0 x 8.5 ( 7 )from the back panel.
Refer to Figure No.1.
Figure No.1
2. Pull both sides of the TOP COVER slightly outwards 8 and tilt approx. 35˚ and then remove
in the direction as indicated by the arrow 9 . Refer to Figure No.2.
Figure No.2.
7
6
5
1
3
2
4
9
8
8

SURROUND SOUND RECEIVER AA
AAVV VVRR RR22 2200 0000 00
- 5 -
WIRING DIAGRAM

SURROUND SOUND RECEIVER AA
AAVV VVRR RR22 2200 0000 00
- 6 -
COAXIAL x3 OPTICAL x2
4053
74LS157
M624476FP
Com-Video
Trigger IN
POWER DOWN Detect Pin. For SPK off, Mute ON, VFD off.
BLOCK DIAGRAM

SURROUND SOUND RECEIVER AA
AAVV VVRR RR22 2200 0000 00
- 7 -
OSC RF
ADJUSTMENT POINTS DIAGRAM
1. TUNER
2. IDLE CURRENT - Front Amplifier & Surround Amplifier Board

SURROUND SOUND RECEIVER AA
AAVV VVRR RR22 2200 0000 00
- 8 -
INSTRUMENT SETUP
1. FM MEASUREMENT
Fig. 1
Fig. 2
2. RDS MEASUREMENT
Fig. 3
3. AM MEASUREMENT
Fig. 4
FM
SIGNAL
GENERATOR
ANTENNA
TERMINAL OUTPUT TERMINAL
DISTORTION
ANALYZER
DISTORTION
ANALYZER
AC
VOLTMETER
OSCILLOSCOPE
AC
VOLTMETER
OR
OSCILLOSCOPE
AC
VOLTMETER
OR
OSCILLOSCOPE
OUTPUT
TERMINAL
OUTPUT
TERMINAL
L
R
ANTENNA
TERMINAL
ANTENNA
TERMINAL
ANTENNA
TERMINAL
AM LOOP
ANTENNA
(Accessory)
AM LOOP
ANTENNA
60cm
DIGITAL
MILLIVOLT
METER
VT-J914
FM
SIGNAL
GENERATOR
AM
SIGNAL
GENERATOR
FM
SIGNAL
GENERATOR
RDS
GENERATOR
FM
STEREO
GENERATOR
P-901
DC
MILLIVOLT
METER
UNIT
UNIT
UNIT
UNIT
ALIGNMENT PROCEDURES
AMPLIFIER SECTION
Idle Current
Step Item Connection Adjustment Adjust for
1Front Left Channel Voltmeter to P502 on Front Amp Board R574 2mV±0.2mV
2Front Right Channel Voltmeter to P501 on Front Amp Board R573 2mV±0.2mV
3Center Channel Voltmeter to P503 on Front Amp Board R599 2mV±0.2mV
4Rear Left Channel Voltmeter to JP801 on Surround Amplifier Board R867 2mV±0.2mV
(PCB N0901C-AMP2)
5Rear Right Channel Voltmeter to JP802 on Surround Amplifier Board R868 2mV±0.2mV
(PCB N091C-AMP2)

SURROUND SOUND RECEIVER AA
AAVV VVRR RR22 2200 0000 00
- 9 -
FM/RDS SECTION
- FM mono: 1kHz, 75kHz devi., 60dB/µV
- FM stereo: 1kHz, 67.5kHz devi., 60dB/µV
Pilot signal 19kHz 7.5kHz devi.
OUTPUTS
- Connect the non-inductive type resistor of 8 ohms to the all speaker terminals unless otherwise noted.
Item
FM
IF/RF
Stereo
Distortion
Stereo
Separation
Muting
Level Signal output
Step
1DC voltmeter L941 0±100mV
3Distortion
analyzer
Distortion
analyzer
Oscilloscope
Oscilloscope
L942
R956
R941
Minimum
Minimum
2AC voltmeter IFT on the
front end
IFT on the
front end
Maximum
Maximum
separation
Connection
of instrument
Fig.1 –
–
Fig.2
Fig.2
Fig.1
Channel L
or R 1kHz
99.0MHz
1kHz 75kHz devi.
65dBf (60dB)
99.0MHz Ext.
mod. 65dBf
(60dB)
FM SG
output Stereo mod- ulator output Tuning frequency
99.0MHz
99.0MHz
Channel L
or R 1kHz
99.0MHz Ext.
mod. 65dBf
(60dB)
99.0MHz Ext.
mod.65dBf(60dB)
RDS 2% MOD
99.0MHz 18dB
99.0MHz
99.0MHz
RDS –
––
–
Fig.3 99.0MHz
Output
indicator Adjustment point Adjust
for Remarks
FM MUTE/MODE
switch: ON/AUTO
Repeat the steps
1 to 3 until no fur-
ther adjustment is
necessary.
FM MUTE/MODE
switch: ON/AUTO
Don’t turn more
than +/-180˚
Repeat stereo
distortion and
stereo separation
alignment until
THD at minimum
and separation at
maximum.
Decode the RDS-
Program Station.
AM SECTION
AM Modulation: 400Hz, 30%
Step
1–
2
3
522kHz
or
531kHz
603kHz
999kHz
600kHz
400Hz 30% mod.
60dB/m
AM SG
output Tuning frequency Output indicator Adjustment point
600kHz
400Hz 30% mod.
60dB/m
AC
voltmeter
AC
voltmeter
Digital
DC
voltmeter
L972
OSC coil
on RF
block L971
RF coil
on RF
block L971
Adjust
for
1.3±0.2V (522kHz)
1.35±0.2V (531kHz)
Maximum
Maximum
IMPORTANT NOTES
1. Show the software version
Press “DISPLAY”, “5.1 INPUT” and “VIDEO 4”.
2. Toggle between PAL and NTSC
Press “MEMORY” and “VIDEO 1”.
3. Light up all the icon on the VFL.
Press “DISPLAY”, “5.1 INPUT” and “VIDEO 1”.
4. Clear all tuner presets
Press “5.1 INPUT” and “VIDEO 1”.

SURROUND SOUND RECEIVER AA
AAVV VVRR RR22 2200 0000 00
- 10 -
PCB LAYOUT
AUDIO BOARD
COMPONENT VIDEO BOARD

SURROUND SOUND RECEIVER AA
AAVV VVRR RR22 2200 0000 00
- 11 -
AC-3 BOARD - Component Side

SURROUND SOUND RECEIVER AA
AAVV VVRR RR22 2200 0000 00
- 12 -
AC-3 BOARD - Solder Side

SURROUND SOUND RECEIVER AA
AAVV VVRR RR22 2200 0000 00
- 13 -
AMP1 BOARD

SURROUND SOUND RECEIVER AA
AAVV VVRR RR22 2200 0000 00
- 14 -
AMP2 BOARD
SPEAKER BOARD

SURROUND SOUND RECEIVER AA
AAVV VVRR RR22 2200 0000 00
- 15 -
KEY BOARD - Component Side KEY BOARD - Solder Side

SURROUND SOUND RECEIVER AA
AAVV VVRR RR22 2200 0000 00
- 16 -
MAIN BOARD

SURROUND SOUND RECEIVER AA
AAVV VVRR RR22 2200 0000 00
- 17 -
MULTI CHANNEL BOARD

SURROUND SOUND RECEIVER AA
AAVV VVRR RR22 2200 0000 00
- 18 -
TUNER BOARD

SURROUND SOUND RECEIVER AA
AAVV VVRR RR22 2200 0000 00
- 19 -
S-VIDEO BOARD
PSU BOARD
SECONDARY BOARD