Arkon GPS032 User manual

[phone]
[phone]
[phone]
[phone]
ICQ:495-089-192
ICQ:613-211-859
User's Manual
Bicycle holder + waterproof case for GPS navigator Arkon GPS032
In the online store Winauto you also can buy кейс для комунікатора аркон Arkon GPS032. Delivery in Kyiv and
throughout Ukraine with payment upon receipt!
winauto.ua
Sale - Car Receivers - Facia Plates - Head Units - Car TVs and Monitors - Antennas - Car Audio - DVR - GPS Navigation - Trip Computers - Car
Alarm Systems - Mechanical Locking - Parking Systems - Car Cameras - Xenon and Lights - Established Optics - Tuning - Car Heating and Cooling -
Sound Marine and Electronics - Car Accessories - Isolation - Installation Components - Batteries, Power - Oils and Fluids -

!
GPS032
|Bicycle or Motorcycle Handlebar Mount and Water-Resistant Case for GPS
The Mobile Mounting Specialists™
®
Consumer Hotline:
USA [phone]
INT’L [phone]
Monday - Friday 9 am - 5 pm, PST
www.arkon.com
Arcadia, CA 91006 USA
Designed in USA | Made in China
© Copyright 2010 Arkon Resources, Inc.
Package Contents:
(1) GN032-SBH - Bicycle or Motorcycle Handlebar Mount with
swivel tightening ring
(1) GPS-WPCS - Bicycle / Motorcycle handlebar mount with
water-resistant GPS case.
(1) Set Screw
Step 1.
Step 2.
Safety Precautions
Do not reposition the pedestal while cycling or driving. Arkon
Resources, Inc. does not promote the adjustment of mobile devices
except when the bicycle or vehicle is safely parked or stopped.
Arkon is not responsible for any damages caused to your bicycle, your
device, or yourself due to the installation or use of this product.
!Precaution: A set screw has been provided to be installed
into the back side of the water resistant case to secure it to
the handlebar pedestal. Ensure that the screw is properly
installed to prevent the case from falling from the pedestal.
Choose a safe location on the handlebars of your bicycle
in which to mount the pedestal.
Using a screwdriver, remove the two mounting screws (A)
in order to release the ball plate and swivel head (B) so the
mount can be placed around the handlebars. Ensure the
screw nuts (C) are not lost when loosening the screws.
Bicycle Handlebar Mounting
Wrap the rubber rings (D) around the handlebar and
reassemble the ball plate and swivel head (E) around the
rubber rings. Secure the mount assembly by using the
screwdriver to retighten the two mounting screws into the
screw nuts (F) through the screw holes.
Step 3.
GPS-WPCS
Water-resistant
GPS Case
GN032-SBH
Bicycle or Motorcycle
Handlebar Mount
Step 5.
Step 4.
Snap the dual-T head adapter plate (K) onto the handlebar
mount ball (L). Adjust the angle as needed and screw the
threaded tightening (M) ring onto the adapter plate until the
plate is securely held in place.
Connect the dual T-tabs (G) on dual T-tab adapter head to
the dual T-slots (H) on the water-resistant GPS case. Insert
the set screw (I) into the set screw hole (J) and screw in
tightly to prevent the pedestal head from slipping off.
Connect Water-resistant GPS Case to Pedestal
B
A
C
C
A
M
K
L
G
H
J
I
Fits handlebars up to 33mm diameter. Compatible with most straight, drop, trekking,
touring, and standard (25.4mm and 26mm) size handlebars. Also for use with golf carts, ATVs,
snowmobiles, hang gliders or other apparatus having cylinder-shaped frames or posts.
Set Screw
D
E
F
F
Интернет-магазин автозвука и автотоваров Винавто
winauto.ua
Powered by TCPDF (www.tcpdf.org)