ArtFox SHINE BAR 12Q User manual

7、 MAINTENANCE
8、 TROUBLESHOOTING
PROBLEM REASON AND ACTION
The lighng can’t be
started normally
Check the power conneconis correct or not.
Please detect the voltage.
Power supply is damaged or incorrect connected. Call a qualified
personnel to fix it.
Conneconof control board is not correct. Call a qualified personnel
to fix it.
Out of console’s
control
Please check the DMX connector and the power conneconis
connected correctly or not. It means having signal if it shows twinkling
of the decimal point which inthe lower right corner of the screen
whenexing the screensaver.
Please check the DMX address seng of lighng is correct or not.
Check【CHMD】seng is correct or not.
Please check whether the DMX line is near to the high voltage wire or
not. Inthat case, it will damage or interfere the DMX electric circuit.
The beam appears
dim ,the brightness
declines obviously
Check whether the 【CAL】is started or not and the set value is too
small.
Check whether the【POW】is inover temperature proteconsituaon
or not, if yes, please take measures for venlaon.
To prolong the life of lighng, it is very important to do the maintenance work. The
environment is hash outdoors, or if the lighng is idle for a long me, damp, dust can cause
greater accumulaon of dirt on its cover or housing. So it should be cleaned to maintain an
opmum light output and at the same me to prevent it from corrupted by dust and acid gas.
Cleaning frequency depends on the lighng operaon frequency and the environment in
which the fixture operates. So cloth and typical glass cleaning products should be used for
cleaning. It is recommended to clean projector at least once every 20 days.
Do not use any organic solvent,e.g.alcohol, to clean housing of the apparatus.
－１１－
SHINE BAR 12Q
Please read it carefully
USER MANUAL

INDEX
1
.SAFETY GUIDELINE..........................................................................................- 2 -
2
. TECHNICAL PARAMETER ..................................................................................- 3 -
3
. LIGHTING INSTALLATION..................................................................................- 4 -
4
. POWER SUPPLY-CONTROL SIGNAL CONNECTIONS............................................- 4 -
5
. OPERATION MENU ..........................................................................................- 5 -
5. 1 BUTTON OPERATION ........................................................................................ - 7 -
5. 2 DMX ADDRESS CODE SETTING .......................................................................... - 7 -
5. 3 STATIC SETTING................................................................................................ - 7 -
5. 4 COLOR CAST CALIBRATION SETTING.................................................................. - 7 -
5.5 CHANNEL MODE SETTING ................................................................................ - 7 -
5. 6 DIMMING MODE SETTING................................................................................ - 7 -
5.7 DISPLAY SETTING .............................................................................................. -7 -
5.8 RUNNING THE AUTO-RUN,AUTO-PROGRAMMING PROGRAM............................ -7 -
5.9 EDITTING THE AUTO-PROGRAMMING PROGRAM .............................................. -8 -
5.10 LIGHTING INFORMATION VIEW ...................................................................... - 8 -
5.11 LIGHTING SETTING PARAMETER RESET ........................................................... - 8 -
5.12【PROG】AUTO-PROGRAMMING PARAMETER RESET ...................................... -8 -
5.13 LIGHTING RESET .............................................................................................. -8 -
5.14 LIGHTING PARAMETER DOWNLOADING EACH OTHER ..................................... - 8 -
7.
MAINTENANCE
..........................................................................................-
11
-
8.
TROUBLESHOOTING ...................................................................................- 11
-
6.
DMX PROTOCOL 9
-
ACCESSORIES
These items are packed together with the Lighting，please check：
Name Quanty Unit Remark
This manual 1 Pc
Power cable 1 Pc
..........................................................................................-
－１０－
76-80 AUTO 5
81-85 AUTO 6
86-90 AUTO 7
91-95 AUTO 8
96-100 AUTO 9
101-105 AUTO 10
106-110 AUTO 11
111-115 AUTO 12
116-120 AUTO 13
121-125 AUTO 14
126-130 AUTO 15
131-135 AUTO 16
136-140 AUTO 17
141-145 AUTO 18
146-150 AUTO 19
151-155 AUTO 20
156-160 AUTO 21
161-165 AUTO 22
166-170 AUTO 23
171-175 AUTO 24
176-180 AUTO 25
181-185 AUTO 26
186-190 AUTO 27
191-195 AUTO 28
196-200 AUTO 29
201-205 AUTO 30
206-210 AUTO 31
211-215 AUTO 32
216-220 AUTO 33
221-225 CHASE1
226-230 CHASE2
231-235 CHASE3
236-255 Reserved
- - CH8 CH16 0—255 Auto speed,fast->slow,(AT01-AT05:0-255S,AT06-AT33:0-25.5S)
Virtual colour wheel
0-10 No effect
11 Blue (Blue=full, Red+Green+White=0)(step)
12-50 Red=0, Green->up,Blue =full, White=0(proportional)
51 Light Blue (Red=0, Green=full, Blue =full, White=0)(step)
52-90 Red=0, Green=full, Blue->down, White=0(proportional)
91 Green (Red=0, Green=full, Blue =0, White=0)(step)
92-130 Red->up, Green=full, Blue=0, White=0(proportional)
131 Yellow (Red=full, Green=full, Blue=0, White=0)(step)
132-170 Red=full, Green->down, Blue=0, White=0(proportional)
171 Red(Red=full, Green=0, Blue=0, White=0)(step)
172-210 Red=full, Green=0, Blue->up, White=0(proportional)
211 Magenta (Red=full, Green=0, Blue=full, White=0)(step)
212-250 Red -> down, Green=0, Blue=full, White=0(proportional)
251-255 Blue (Red=0, Green=0, Blue=full, White=0)(step)
0-10 Use menu setting dimmer mode
11-20 Dimmer off
21-30 Dimmer 1
31-40 Dimmer 2
41-50 Dimmer 3
51-60 Dimmer 4
61-254 Use menu setting dimmer mode
255 Reset（at least 5S）
CH18CH10-
CH17CH2
CH7-
CH9- -
Remark：
AT01:R,G,B,RG,RB,GB
AT02:R↑,R↓,G↑,G↓,B↑,B↓,W↑,W↓
AT03:R↑G↑,R↓G↓,R↑B↑,R↓B↓,B↑G↑,B↓G↓
AT04:R↑G↑B↑W↑,R↓G↓B↓W↓
AT05:(Rainbow effect)B,BG↑,BG,B↓G,G,GR↑,GR,G↓
R,R,RB↑,RB,R↓B
AT06:R1→R2→R3
AT07:G1→G2→G3
AT08:B1→B2→B3
AT09:W1→W2→W3
AT10:R1G1→R2G2→R3G3
AT11:R1B1→R2B2→R3B3
AT12:G1B1→G2B2→G3B3
AT13:G3R2→R3G1→G2R1
AT14:R3B3R2G2→R1B1R3G3→R2B2R1G1
AT15:B3W2→B1W3→B2W1
AT16:R1G2B3→B1R2G3→G1B2R3
AT17:R1G2G3→G1R2G3→G1G2R3
AT18:G1B2B3→B1G2B3→B1B2G3
AT19:B1R2R3→R1B2R3→R1R2B3
AT20:R1←R2←R3
AT21:G1←G2←G3
AT22:B1←B2←B3
AT23:W1←W2←W3
AT24:R1G1←R2G2←R3G3
AT25:R1B1←R2B2←R3B3
AT26:G1B1←G2B2←G3B3
AT27:G3R2←R3G1←G2R1
AT28:R3B3R2G2←R1B1R3G3←R2B2R1G1
AT29:B3W2←B1W3←B2W1
AT30:R1G2B3←B1R2G3←G1B2R3
AT31:R1G2G3←G1R2G3←G1G2R3
AT32:G1B2B3←B1G2B3←B1B2G3
AT33:B1R2R3←R1B2R3←R1R2B3

－２－
１、SAFETY GUIDELINE

Whenreceiving the lighng ，please dispose the carton, check and inspect there is any
damage or not. Should there be any damage caused by transportaon，do not use the lighng
and consult your dealer or the manufacturer.
This lighng canbe used indoors and outdoors, IP65.
The lighng is only intended for installaonand operaonby qualified personnel.
Do not mount the lighng directly onto inflammable surface.
Ensure power supply voltage correspond to device requirements before running.
It is essenal that each lighng is correctly earthed and that electrical installaonconforms
to all relevant standards.
Whenthe lighng is hanged to a high place, please use a safety cord provided to pass
through the lighng handles as a secondary safety fixing for safety seasons. For details, refer to
“LIGHTING INSTALLATION” secon.
Avoid direct exposure to the light from the lamp（specially for people with epilepsy）. The light
is harmful to eyes.
Do not project the beam onto inflammable surfaces. The minimum distance betweenthe
lighng and irradiated object should be 2m.
Exterior surface temperature of the lighng will be 65℃whenworking，please do not touch
it with bare hands .
To prevent electric shocking, please do not touch the power cord whenthe lighng is
running.
Never let the power cord mix with other cables.
The LED lens should be changed if deeply scratched or cracked.
There is no user serviceable parts inside the lighng. Before using the device, please check
whether the covers or housing are well installed or not, and whether the screws are installed firmly
or not. Do not openthe housing and never operate the lighng with the covers removed.
Always disconnect a lighting from the power supply when the device is not in use or
before cleaning it or before attempting any maintenance work!
Electrical connection must only be carried out by qualified personnel.
Please use the original packing material for second transportation.
If you have any questions or suggestions, please do not hesitate to consult your
dealer or our factory.

－９－
Please keep this manual for further inquire reference. Please make sure they also have this
user manual if you sell this Lighng to other users. Each unit is packed properly by the
manufacturer. Please operate this Lighng according to the user manual. Any damage caused
by improper use will not be assumed by the manufacturer.
6、DMX PROTOCOL
2CH 5CH 7CH 10CH 18CH Value Function
- CH1 CH1 CH1 CH1 0-255 Dim all
- CH2 CH2 CH2 - 0-255 Red
- CH3 CH3 CH3 - 0-255 Green
- CH4 CH4 CH4 - 0-255 Blue
- CH5 CH5 CH5 - 0-255 White
- - - - CH2 0-255 Red 1
- - - - CH3 0-255 Green 1
- - - - CH4 0-255 Blue 1
- - - - CH5 0-255 White 1
- - - - CH6 0-255 Red 2
- - - - CH7 0-255 Green 2
- - - - CH8 0-255 Blue 2
- - - - CH9 0-255 White 2
- - - - CH10 0-255 Red 3
- - - - CH11 0-255 Green 3
- - - - CH12 0-255 Blue 3
- - - - CH13 0-255 White 3
0-10 No strobe
11-90 Strobe，slow->fast
91-170 Random Strobe，slow->fast
171-255 Electronic Squarewave，slow->fast
0-5 No effect
6-10 WHITE 1:3200K
11-15 WHITE 2:3400K
16-20 WHITE 3:4200K
21-25 WHITE 4:4900K
26-30 WHITE 5:5600K
31-35 WHITE 6:5900K
36-40 WHITE 7:6500K
41-45 WHITE 8:7200K
46-50 WHITE 9:8000K
51-55 WHITE 10:8500K
56-60 AUTO 1
61-65 AUTO 2
66-70 AUTO 3
71-75 AUTO 4
- - -
CH7(CH7
Prior to
CH9)
CH15(CH15
Prior to
CH17)
CH1 CH6 CH14- CH6

－３－ －８－
5.9 EDIT AUTO-PROGRAMMING PROGRAM
1) Press the【ENTER】buonin【PROGRAM】menu, thenenter to the eding auto-programming
program.
2)Press the【UP/DOWN】buonto select【CHASE01】…【CHASE03】
3) Press the【ENTER】buonfor confirmaonand enter to the next menu.
4) Press the【UP/DOWN】buonto select【SCENE01】…【SCENE20】
5) Press the【ENTER】buonfor confirmaonand enter to the next menu.
6) Thenpress the【UP/DOWN】buonto select【RED1】，【GREEN1 】……【WHITE3】，【SHUT】，
【TIME】，【WAIT】，【USE】
7) Press the【UP/DOWN】buonto set up the parameter which are needed.
8) Press the【ENTER】buonto escape and save.
5.10 CHECK THE LIGHTING INFORMATION
1) Press the【ENTER】buonin【INFO】menu, thenenter to the checking
the lighng informaon.
2)【SOFT】buonis for soware versioninformaon.
3) 【LEDs】buonis for the LED quanty informaon.
4) 【POW】buonis for the current informaonof power reducon. It is 100% output innormal
condions, but 80% or 50% output inover temperature proteconsituaon.
5.11 LIGHTING SETTING PARAMETER RESET
1) Press the【ENTER】buonin【ST L】menu, thenenter to the lighng seng parameter reset.
2)Press the【UP/DOWN】buonto select【YES】.
3) Press the【ENTER】buonto escape and save.
5.12 【PROG】AUTO-PROGRAMMING PARAMETER RESET
1) Press the【ENTER】buonin【PR L】menu, thenenter to the【PROG】auto-programming
parameter reset.
2)Press the【UP/DOWN】buonto select【YES】.
3) Press the【ENTER】buonto escape and save.
5.13 LIGHTING RESET
1) Press the【ENTER】buonin【REST】menu, thenenter to the lighng reset.
2)Press the【UP/DOWN】buonto select【YES】.
3) Press the【ENTER】buonfor confirmaonof lighng reset.
5.14 LIGHTING PARAMETER DOWNLOADING EACH OTHER
1) Press the【ENTER】buonin【SEND】menu, thenenter to sending parameter to other lighngs.
2)Press the【UP/DOWN】buonto select【YES】.
3) Press the【ENTER】buonto confirm sending.
Illustrations：When【USE】 is set to be【NO】，or the
parameter of【TIME】 is 0, it will not run this scene.
When 【WAIT】is set to be FADE time, the running process
isas the right chart showing.
2)Press the【UP/DOWN】button to select【AT01】…【AT33】，【SPEED】，【
CHASE01】…【CHASE03】
3)Press the【ENTER】button to start running.
２、TECHNICAL PARAMETER
Input Voltage：AC100V-AC240V，50/60HZ；
Power Consumpon：120W ;
Lamp Specificaons：12 pcs four inone（RGBW) high-efficiency 10W LED, rated life 50000
hours；
Lens Angle：25º（Oponal：45°）；
Spot Angle：40º；
Color：RGBW linear color mixing；
Color Temperature：color cast calibraonseng、color temperature output inside device；
Dimmer：0-100% linearly dimming，5 types dimmer modes，smooth dimming, flicker-free；
Shuer：independent electronic strobe；
Control Mode：
Standard DMX512，3 pininterfaces；
5 channel modes；
Master/slave mode，no need to set up the master and slave manually, will receive the main
engine data automacally;
33 auto-running modes，rainbow channel and rainbow effect；
Other Funcons：
Self-programming funcon, 3 chases，each chase has 20 scenes，fade funcon;
Lighng seng data、self-programming data canbe downloaded each other;
Temperature Control Protecon：Both of lamp holder and base have temperature control
protecon;
Waterproof Grade：IP65；
Work Environment Temperature：-20°C～40°C；
Net Weight：5.6 Kg；
DIMENSION

－４－
－７－
ＭＯＵＮＴＩＮＧ ＨＯＬＥ ＦＯＲ ＬＡＭＰ ＨＯＯＫ
ＳＡＦＥＴＹ ＲＩＮＧ
ＴＨＥ ＳＣＲＥＷ ＨＯＬＥ


PICTURE ONE
PICTURE TWO
The lighting can be hanged on the high place with using the lamp hooks (as showed in
picture 1). Use the safety cord provided to pass through the bottom safe ring and
hang it as a second safety fixing.
The lighting also can place on the ground and make sure balance stand ,as showed in
picture 2.


Note:
Ensure support loading ability at least 10 times more than product weight，and make
sure lighting be firmly installed.
The lighting must be installed by the qualified personnel. Please install it at the
place where no one goes through.
4、 POWER SUPPLY-CONTROL SIGNAL CONNECTIONS
Make the XLR signal line connect with the lighng, one port connects with the output port of
lighng, another one connects with the input port of another lighng.
Due to the output and input of the lighng keep connecng all the me, so the DMX circuit
sll canbe keep connecng whenthe power of certainunit occurs turn-off.
XLR signal line only canbe used inseries conneconpaern(the amount of the lighng can
not be more than32PCS), not available inparallel conneconpaern. Must add a signal
amplifier if the length of signal line exceeds 60M betweencontroller and lighng or between
two lighngs.
Inthe controller mode, at the last fixture inthe chain, the DMX output
has to be connected with a DMX terminator. The DMX terminator is
simply a connector with a resistor about 120Ω（OHM）connected
across pins 2 and 3 of the Canon plug（please see the picture
in the right）.It canprevent the noise and refleconcaused by DMX
512signal during transmission.
3、 LIGHTING INSTALLATION
5.1 BUTTON OPERATION
1) MENU：To returnto the previous menu.
2)ENTER：Enter to the next menu or save.
3) UP：Menu seleconor increasing the parameter.
4) DOWN：Menu seleconor decreasing the parameter.
5.2 DMX ADDRESS CODE SETTING
1) Press the 【ENTER】buonin【ADDR】menu, thenenter to the DMX address code seng.
2)Press the【UP/DOWN】buonto select【1-512】numerical value.
3) Press the【ENTER】buonto escape and save.
5.3 STATIC SETTING
1) Press the【ENTER】buonin【STAT】menu, thenenter to the stac seng.
2)Press the【UP/DOWN】buonto select 【RED1】，【GREEN1】……【WHITE3】and【SHUT】.
3) Press the【UP/DOWN】buonto set up the【0-255】numerical value.
4) Press the【ENTER】buonto escape and save.
5.4 COLOR CAST CALIBRATION SETTING
1) Press the【ENTER】buonin【CAL】menu, thenenter to the color cast calibraonseng.
2)Press the【UP/DOWN】buonto select 【RED】，【GREEN】，【BLUE】，【WHITE】
3) Press the【UP/DOWN】buonto set up the【0-255】numerical value.
4) Onthe【USE】interface, pressing【ON】buonmeans valid, otherwise【OFF】buoninvalid.
5) Press the【ENTER】buonto escape and save.
5.5 CHANNEL MODE SETTING
1) Press the【ENTER】buonin【CHMD】menu, thenenter to the channel mode seng.
2)Press the【UP/DOWN】buonto select【18CH】，【10CH】，【7CH】，【5CH】,【2CH】
3) Press the【ENTER】buonto escape and save.
5.6 DIMMING MODE SETTING
1) Press the【ENTER】buonin【DIM】menu, thenenter to the dimming mode seng.
2)Press the【UP/DOWN】buonto select【OFF】，【DIM1】，【DIM2】，【DIM3】and【DIM4】
3) Press the【ENTER】buonto escape and save.
5.7 DISPLAY SETTING
1) Press the【ENTER】buonin【DISY】menu, thenenter to the display seng.
2)Press the【UP/DOWN】buonto select【ON】，【2MINITES OFF】
3) Press the【ENTER】buonto escape and save.
5.8 RUN THE AUTO-RUN, AUTO-PROGRAMMING PROGRAM
Illustrations: When pressing the【ON】button which means valid on the【USE】
interface, the actual output value of RED，GREEN，BLUE，WHITE is output in
accordance with the percentage which the color cast calibration value divides 255.
Illustrations：When setting【OFF】 in【DIM】menu, there will be no delay dimming
effect. The dimming speed of DIM1-DIM4 is from fast to slow. It will be set【OFF
】automatically in【DIM】menu when showing the shutter effect.
1)Press the【ENTER】button in【AUTO】menu, then enter to the running the auto-run,
auto-programming program.

－６－
－５－
ＰＯＷＥＲ ＩＮ ＴＯ ＴＥＲＭＩＮＡＴＯＲ
ＰＯＷＥＲ ＯＵＴ
ＤＭＸ ＯＵＴ
ＤＭＸ ＣＯＮＳＯＬＥ
5、 OPERATION MENU
The transmissionspeed of DMX 512signal is very quick. It will affect the signal transmissionif
any damage of the signal line, the weld is not firm or bad conneconetc
The connector with 3 pins XLR is more universal thanthe one with 5 pins XLR.
3 pins XLR：PIN 1：GND，PIN 2：- signal，PIN 3：+ signal.
5 pins XLR：PIN 1：GND，PIN 2：- signal，PIN 3：+ signal，PIN4/PIN5：UNUSED.
There can’t be more than12 PCS of lighngs for series conneconpaernwhenusing 220V
AC; it can’t exceed 6 PCS lighngs for series conneconpaernwhenusing 110V AC.
Tab Level 1 Level 2 Level 3 Level 4
ADDR(Address) 001-512
STAT(Static control) R1 0-255 *
G1 0-255 *
B1 0-255 *
W1 0-255 *
R2 0-255 *
G2 0-255 *
B2 0-255 *
W2 0-255 *
R3 0-255 *
G3 0-255 *
B3 0-255 *
W3 0-255 *
SHUT 0-255 *
SET(Set) CAL(Calibration) R(Red) 0-255
G(Green) 0-255
B(Blue) 0-255
W(White) 0-255
USE YES/NO
CH(Channel mode) 18CH
10CH
7CH
5CH
2CH
D(Dimming mode) OFF
D1
D2
D3
D4
DISY(Display set) ON(Permanent on)
2 OF (2 minutes
off)
Illustrations：
When the menu is set as the information of * position, the
projector will be set automatically to be the main engine and then
send data to external. Other projectors can receive these data and run
synchronously with the main engine. It still be run according to these
setting parameter even if power reconnection after power off .
When setting YES in【ST L】menu, The parameter will bereset to be
the factory default value as which with underline of above chart.
CTST(Color
temperature set)
CT01 R(Red) 0-255
. G(Green) 0-255
. B(Blue) 0-255
. W(White) 0-255
CT10
AUTO(Auto) AT01 RUN.. *
. RUN.. *
. RUN.. *
. RUN.. *
AT33 RUN.. *
ATSP(Auto speed) 0-255(S)
CHS1（Chase 1）RUN.. *
CHS2（Chase 2）RUN.. *
CHS3（Chase 3）RUN.. *
PROG（Program）CHS1（Chase 1）SC01（Scene 1）R1 0-255
. . G1 0-255
. . B1 0-255
. . W1 0-255
. . R2 0-255
. . G2 0-255
. . B2 0-255
. . W2 0-255
. . R3 0-255
. . G3 0-255
. . B3 0-255
. . W3 0-255
. . SHUT 0-255
. . AUTO NONE,AT01-AT33
. . ATSP 0-255(S)
. . TIME 0-255(S)
. . WAIT 0-25.5(S)
. . USE YES/NO
. SC25（Scene 25）
CHS3（Chase 3）
INFO（Information）SOFT(Software
version) Vx.x
LEDs xxR
xxG
xxB
xxW
POW(Power reduction) 100%/80%/50%
LOAD(Load) ST L（Setting load) YES/NO
PR L（Program load) YES/NO
REST(Reset) YES/NO
SEND(Send) YES/NO